mirror of
https://github.com/arduino/Arduino.git
synced 2024-11-30 11:24:12 +01:00
69 lines
2.8 KiB
C
69 lines
2.8 KiB
C
|
/*! \file uartsw2conf.h \brief Interrupt-driven Software UART Driver Configuration. */
|
||
|
|
//*****************************************************************************
|
||
|
|
//
|
||
|
|
// File Name : 'uartsw2conf.h'
|
||
|
|
// Title : Interrupt-driven Software UART Driver Configuration
|
||
|
|
// Author : Pascal Stang - Copyright (C) 2002-2003
|
||
|
|
// Created : 7/20/2002
|
||
|
|
// Revised : 4/27/2004
|
||
|
|
// Version : 0.6
|
||
|
|
// Target MCU : Atmel AVR Series (intended for the ATmega16 and ATmega32)
|
||
|
|
// Editor Tabs : 4
|
||
|
|
//
|
||
|
|
// Description :
|
||
|
|
// This uart library emulates the operation of a UART (serial port) using
|
||
|
|
// the AVR's hardware timers, I/O pins, and some software.
|
||
|
|
//
|
||
|
|
// Specifically, this code uses:
|
||
|
|
// -Timer 2 Output Capture for transmit timing
|
||
|
|
// -Timer 0 Output Capture for receive timing
|
||
|
|
// -External Interrupt 2 for receive triggering
|
||
|
|
//
|
||
|
|
// The above resources cannot be used for other purposes while this software
|
||
|
|
// UART is enabled. The overflow interrupts from Timer0 and Timer2 can still
|
||
|
|
// be used for other timing, but the prescalers for these timers must not be
|
||
|
|
// changed.
|
||
|
|
//
|
||
|
|
// Serial output from this UART can be routed to any I/O pin. Serial input
|
||
|
|
// for this UART must come from the External Interrupt 2 (INT2) I/O pin.
|
||
|
|
// These options should be configured by editing your local copy of
|
||
|
|
// "uartsw2conf.h".
|
||
|
|
//
|
||
|
|
// This code is distributed under the GNU Public License
|
||
|
|
// which can be found at http://www.gnu.org/licenses/gpl.txt
|
||
|
|
//
|
||
|
|
//*****************************************************************************
|
||
|
|
|
||
|
|
#ifndef UARTSW2CONF_H
|
||
|
|
#define UARTSW2CONF_H
|
||
|
|
|
||
|
|
// constants/macros/typdefs
|
||
|
|
|
||
|
|
#define UARTSW_RX_BUFFER_SIZE 0x20 ///< UART receive buffer size in bytes
|
||
|
|
|
||
|
|
#define UARTSW_INVERT ///< define to invert polarity of RX/TX signals
|
||
|
|
// when non-inverted, the serial line is appropriate for passing though
|
||
|
|
// an RS232 driver like the MAX232. When inverted, the serial line can
|
||
|
|
// directly drive/receive RS232 signals to/from a DB9 connector. Be sure
|
||
|
|
// to use a current-limiting resistor and perhaps a diode-clamp circuit when
|
||
|
|
// connecting incoming RS232 signals to a microprocessor I/O pin.
|
||
|
|
|
||
|
|
// if non-inverted, the serial line idles high (logic 1) between bytes
|
||
|
|
// if inverted, the serial line idles low (logic 0) between bytes
|
||
|
|
|
||
|
|
|
||
|
|
// UART transmit pin defines
|
||
|
|
#define UARTSW_TX_PORT PORTB ///< UART Transmit Port
|
||
|
|
#define UARTSW_TX_DDR DDRB ///< UART Transmit DDR
|
||
|
|
#define UARTSW_TX_PIN PB3 ///< UART Transmit Pin
|
||
|
|
|
||
|
|
// UART receive pin defines
|
||
|
|
// This pin must correspond to the
|
||
|
|
// External Interrupt 2 (INT2) pin for your processor
|
||
|
|
#define UARTSW_RX_PORT PORTB ///< UART Receive Port
|
||
|
|
#define UARTSW_RX_DDR DDRB ///< UART Receive DDR
|
||
|
|
#define UARTSW_RX_PORTIN PINB ///< UART Receive Port Input
|
||
|
|
#define UARTSW_RX_PIN PB2 ///< UART Receive Pin
|
||
|
|
|
||
|
|
#endif
|