mirror of
https://github.com/arduino/Arduino.git
synced 2024-12-04 15:24:12 +01:00
76 lines
2.0 KiB
Arduino
76 lines
2.0 KiB
Arduino
|
/*
|
||
|
Calibration
|
||
|
|
||
|
Demonstrates one technique for calibrating sensor input. The
|
||
|
sensor readings during the first five seconds of the sketch
|
||
|
execution define the minimum and maximum of expected values
|
||
|
attached to the sensor pin.
|
||
|
|
||
|
The sensor minimum and maximum initial values may seem backwards.
|
||
|
Initially, you set the minimum high and listen for anything
|
||
|
lower, saving it as the new minimum. Likewise, you set the
|
||
|
maximum low and listen for anything higher as the new maximum.
|
||
|
|
||
|
The circuit:
|
||
|
* Analog sensor (potentiometer will do) attached to analog input 0
|
||
|
* LED attached from digital pin 9 to ground
|
||
|
|
||
|
created 29 Oct 2008
|
||
|
By David A Mellis
|
||
|
modified 30 Aug 2011
|
||
|
By Tom Igoe
|
||
|
|
||
|
http://arduino.cc/en/Tutorial/Calibration
|
||
|
|
||
|
This example code is in the public domain.
|
||
|
|
||
|
*/
|
||
|
|
||
|
// These constants won't change:
|
||
|
const int sensorPin = A0; // pin that the sensor is attached to
|
||
|
const int ledPin = 9; // pin that the LED is attached to
|
||
|
|
||
|
// variables:
|
||
|
int sensorValue = 0; // the sensor value
|
||
|
int sensorMin = 1023; // minimum sensor value
|
||
|
int sensorMax = 0; // maximum sensor value
|
||
|
|
||
|
|
||
|
void setup() {
|
||
|
// turn on LED to signal the start of the calibration period:
|
||
|
pinMode(13, OUTPUT);
|
||
|
digitalWrite(13, HIGH);
|
||
|
|
||
|
// calibrate during the first five seconds
|
||
|
while (millis() < 5000) {
|
||
|
sensorValue = analogRead(sensorPin);
|
||
|
|
||
|
// record the maximum sensor value
|
||
|
if (sensorValue > sensorMax) {
|
||
|
sensorMax = sensorValue;
|
||
|
}
|
||
|
|
||
|
// record the minimum sensor value
|
||
|
if (sensorValue < sensorMin) {
|
||
|
sensorMin = sensorValue;
|
||
|
}
|
||
|
}
|
||
|
|
||
|
// signal the end of the calibration period
|
||
|
digitalWrite(13, LOW);
|
||
|
}
|
||
|
|
||
|
void loop() {
|
||
|
// read the sensor:
|
||
|
sensorValue = analogRead(sensorPin);
|
||
|
|
||
|
// apply the calibration to the sensor reading
|
||
|
sensorValue = map(sensorValue, sensorMin, sensorMax, 0, 255);
|
||
|
|
||
|
// in case the sensor value is outside the range seen during calibration
|
||
|
sensorValue = constrain(sensorValue, 0, 255);
|
||
|
|
||
|
// fade the LED using the calibrated value:
|
||
|
analogWrite(ledPin, sensorValue);
|
||
|
}
|