mirror of
https://github.com/arduino/Arduino.git
synced 2024-12-11 22:24:13 +01:00
126 lines
4.2 KiB
C
Executable File
126 lines
4.2 KiB
C
Executable File
/*! \file mmc.h \brief MultiMedia and SD Flash Card Interface. */
|
|
//*****************************************************************************
|
|
//
|
|
// File Name : 'mmc.h'
|
|
// Title : MultiMedia and SD Flash Card Interface
|
|
// Author : Pascal Stang - Copyright (C) 2004
|
|
// Created : 2004.09.22
|
|
// Revised : 2004.09.22
|
|
// Version : 0.1
|
|
// Target MCU : Atmel AVR Series
|
|
// Editor Tabs : 4
|
|
//
|
|
// Description : This library offers some simple function which can be used
|
|
// to read and write data on a MultiMedia or SecureDigital (SD) Flash
|
|
// Card. Although MM and SD Cards are designed to operate with their own
|
|
// special bus wiring and protocols, both types of cards also provide a
|
|
// simple SPI-like interface mode which is exceptionally useful when
|
|
// attempting to use the cards in embedded systems.
|
|
//
|
|
// To work with this library, the card must be wired to the SPI port of
|
|
// the Atmel microcontroller as described below.
|
|
// _________________
|
|
// / 1 2 3 4 5 6 78 | <- view of MMC/SD card looking at contacts
|
|
// / 9 | Pins 8 and 9 are present only on SD cards
|
|
// | MMC/SD Card |
|
|
// /\/\/\/\/\/\/\/\/\/
|
|
//
|
|
// 1 - CS (chip select) - wire to any available I/O pin(*)
|
|
// 2 - DIN (data in, card<-host) - wire to SPI MOSI pin
|
|
// 3 - VSS (ground) - wire to ground
|
|
// 4 - VDD (power, 3.3V only?) - wire to power (MIGHT BE 3.3V ONLY!)
|
|
// 5 - SCLK (data clock) - wire to SPI SCK pin
|
|
// 6 - VSS (ground) - wire to ground
|
|
// 7 - DOUT (data out, card->host) - wire to SPI MISO pin
|
|
//
|
|
// (*) you must define this chip select I/O pin in mmcconf.h
|
|
//
|
|
// NOTE: This code is currently below version 1.0, and therefore is considered
|
|
// to be lacking in some functionality or documentation, or may not be fully
|
|
// tested. Nonetheless, you can expect most functions to work.
|
|
//
|
|
// This code is distributed under the GNU Public License
|
|
// which can be found at http://www.gnu.org/licenses/gpl.txt
|
|
//
|
|
//*****************************************************************************
|
|
|
|
#ifndef MMC_H
|
|
#define MMC_H
|
|
|
|
#include "global.h"
|
|
|
|
// constants/macros/typdefs
|
|
// MMC commands (taken from sandisk MMC reference)
|
|
#define MMC_GO_IDLE_STATE 0
|
|
#define MMC_SEND_OP_COND 1
|
|
#define MMC_SEND_CSD 9
|
|
#define MMC_SEND_CID 10
|
|
#define MMC_SEND_STATUS 13
|
|
#define MMC_SET_BLOCKLEN 16
|
|
#define MMC_READ_SINGLE_BLOCK 17
|
|
#define MMC_WRITE_BLOCK 24
|
|
#define MMC_PROGRAM_CSD 27
|
|
#define MMC_SET_WRITE_PROT 28
|
|
#define MMC_CLR_WRITE_PROT 29
|
|
#define MMC_SEND_WRITE_PROT 30
|
|
#define MMC_TAG_SECTOR_START 32
|
|
#define MMC_TAG_SECTOR_END 33
|
|
#define MMC_UNTAG_SECTOR 34
|
|
#define MMC_TAG_ERASE_GROUP_START 35
|
|
#define MMC_TAG_ERARE_GROUP_END 36
|
|
#define MMC_UNTAG_ERASE_GROUP 37
|
|
#define MMC_ERASE 38
|
|
#define MMC_CRC_ON_OFF 59
|
|
// R1 Response bit-defines
|
|
#define MMC_R1_BUSY 0x80
|
|
#define MMC_R1_PARAMETER 0x40
|
|
#define MMC_R1_ADDRESS 0x20
|
|
#define MMC_R1_ERASE_SEQ 0x10
|
|
#define MMC_R1_COM_CRC 0x08
|
|
#define MMC_R1_ILLEGAL_COM 0x04
|
|
#define MMC_R1_ERASE_RESET 0x02
|
|
#define MMC_R1_IDLE_STATE 0x01
|
|
// Data Start tokens
|
|
#define MMC_STARTBLOCK_READ 0xFE
|
|
#define MMC_STARTBLOCK_WRITE 0xFE
|
|
#define MMC_STARTBLOCK_MWRITE 0xFC
|
|
// Data Stop tokens
|
|
#define MMC_STOPTRAN_WRITE 0xFD
|
|
// Data Error Token values
|
|
#define MMC_DE_MASK 0x1F
|
|
#define MMC_DE_ERROR 0x01
|
|
#define MMC_DE_CC_ERROR 0x02
|
|
#define MMC_DE_ECC_FAIL 0x04
|
|
#define MMC_DE_OUT_OF_RANGE 0x04
|
|
#define MMC_DE_CARD_LOCKED 0x04
|
|
// Data Response Token values
|
|
#define MMC_DR_MASK 0x1F
|
|
#define MMC_DR_ACCEPT 0x05
|
|
#define MMC_DR_REJECT_CRC 0x0B
|
|
#define MMC_DR_REJECT_WRITE_ERROR 0x0D
|
|
|
|
// functions
|
|
|
|
//! Initialize hardware interface
|
|
void mmcInit(void);
|
|
|
|
//! Initialize the card and prepare it for use
|
|
// returns zero if successful
|
|
u08 mmcReset(void);
|
|
|
|
//! Send card an MMC command
|
|
// returns R1 result code
|
|
u08 mmcSendCommand(u08 cmd, u32 arg);
|
|
|
|
//! Read 512-byte sector from card to buffer
|
|
// returns zero if successful
|
|
u08 mmcRead(u32 sector, u08* buffer);
|
|
//! Write 512-byte sector from buffer to card
|
|
// returns zero if successful
|
|
u08 mmcWrite(u32 sector, u08* buffer);
|
|
|
|
//! internal command function
|
|
u08 mmcCommand(u08 cmd, u32 arg);
|
|
|
|
#endif
|