mirror of
https://github.com/arduino/Arduino.git
synced 2024-12-03 14:24:15 +01:00
68 lines
2.7 KiB
C
Executable File
68 lines
2.7 KiB
C
Executable File
/*! \file uartswconf.h \brief Interrupt-driven Software UART Driver Configuration. */
|
|
//*****************************************************************************
|
|
//
|
|
// File Name : 'uartswconf.h'
|
|
// Title : Interrupt-driven Software UART Driver Configuration
|
|
// Author : Pascal Stang - Copyright (C) 2002-2004
|
|
// Created : 7/20/2002
|
|
// Revised : 4/27/2004
|
|
// Version : 0.1
|
|
// Target MCU : Atmel AVR Series (intended for the ATmega16 and ATmega32)
|
|
// Editor Tabs : 4
|
|
//
|
|
// Description :
|
|
// This uart library emulates the operation of a UART (serial port) using
|
|
// the AVR's hardware timers, I/O pins, and some software.
|
|
//
|
|
// Specifically, this code uses:
|
|
// -Timer 1 Output Compare A for transmit timing
|
|
// -Timer 1 Output Compare B for receive timing
|
|
// -Timer 1 Input Capture for receive triggering
|
|
//
|
|
// The above resources cannot be used for other purposes while this software
|
|
// UART is enabled. The overflow interrupt from Timer1 can still be used for
|
|
// other timing, but the prescaler for Timer1 must not be changed.
|
|
//
|
|
// Serial output from this UART can be routed to any I/O pin. Serial input
|
|
// for this UART must come from the Timer1 Input Capture (IC1) I/O pin.
|
|
// These options should be configured by editing your local copy of
|
|
// "uartswconf.h".
|
|
//
|
|
// This code is distributed under the GNU Public License
|
|
// which can be found at http://www.gnu.org/licenses/gpl.txt
|
|
//
|
|
//*****************************************************************************
|
|
|
|
#ifndef UARTSWCONF_H
|
|
#define UARTSWCONF_H
|
|
|
|
// constants/macros/typdefs
|
|
|
|
#define UARTSW_RX_BUFFER_SIZE 0x20 ///< UART receive buffer size in bytes
|
|
|
|
#define UARTSW_INVERT ///< define to invert polarity of RX/TX signals
|
|
// when non-inverted, the serial line is appropriate for passing though
|
|
// an RS232 driver like the MAX232. When inverted, the serial line can
|
|
// directly drive/receive RS232 signals to/from a DB9 connector. Be sure
|
|
// to use a current-limiting resistor and perhaps a diode-clamp circuit when
|
|
// connecting incoming RS232 signals to a microprocessor I/O pin.
|
|
|
|
// if non-inverted, the serial line idles high (logic 1) between bytes
|
|
// if inverted, the serial line idles low (logic 0) between bytes
|
|
|
|
|
|
// UART transmit pin defines
|
|
#define UARTSW_TX_PORT PORTD ///< UART Transmit Port
|
|
#define UARTSW_TX_DDR DDRD ///< UART Transmit DDR
|
|
#define UARTSW_TX_PIN PD5 ///< UART Transmit Pin
|
|
|
|
// UART receive pin defines
|
|
// This pin must correspond to the
|
|
// Timer1 Input Capture (ICP or IC1) pin for your processor
|
|
#define UARTSW_RX_PORT PORTD ///< UART Receive Port
|
|
#define UARTSW_RX_DDR DDRD ///< UART Receive DDR
|
|
#define UARTSW_RX_PORTIN PIND ///< UART Receive Port Input
|
|
#define UARTSW_RX_PIN PD6 ///< UART Receive Pin
|
|
|
|
#endif
|