mirror of
https://github.com/arduino/Arduino.git
synced 2024-12-04 15:24:12 +01:00
85 lines
3.1 KiB
C++
85 lines
3.1 KiB
C++
/*
|
|
Arduino Yún USB-to-Serial
|
|
|
|
Allows you to use the Yún's 32U4 processor as a
|
|
serial terminal for the Linux side on the Yún.
|
|
|
|
Upload this to an Arduino Yún via serial (not WiFi) then open
|
|
the serial monitor at 115200 to see the boot process of Linux.
|
|
You can also use the serial monitor as a basic command line
|
|
interface for Linux using this sketch.
|
|
|
|
From the serial monitor the following commands can be issued:
|
|
|
|
'~' followed by '0' -> Set the UART speed to 57600 baud
|
|
'~' followed by '1' -> Set the UART speed to 115200 baud
|
|
'~' followed by '2' -> Set the UART speed to 250000 baud
|
|
'~' followed by '3' -> Set the UART speed to 500000 baud
|
|
'~' followed by '~' -> Sends the bridge's shutdown command to
|
|
obtain the console.
|
|
|
|
The circuit:
|
|
* Arduino Yún
|
|
|
|
created March 2013
|
|
by Massimo Banzi
|
|
modified by Cristian Maglie
|
|
|
|
This example code is in the public domain.
|
|
|
|
http://www.arduino.cc/en/Tutorial/YunSerialTerminal
|
|
|
|
*/
|
|
|
|
|
|
long linuxBaud = 250000;
|
|
|
|
void setup() {
|
|
Serial.begin(115200); // open serial connection via USB-Serial
|
|
Serial1.begin(linuxBaud); // open serial connection to Linux
|
|
}
|
|
|
|
boolean commandMode = false;
|
|
|
|
void loop() {
|
|
// copy from USB-CDC to UART
|
|
int c = Serial.read(); // read from USB-CDC
|
|
if (c != -1) { // got anything?
|
|
if (commandMode == false) { // if we aren't in command mode...
|
|
if (c == '~') { // Tilde '~' key pressed?
|
|
commandMode = true; // enter in command mode
|
|
} else {
|
|
Serial1.write(c); // otherwise write char to UART
|
|
}
|
|
} else { // if we are in command mode...
|
|
if (c == '0') { // '0' key pressed?
|
|
Serial1.begin(57600); // set speed to 57600
|
|
Serial.println("Speed set to 57600");
|
|
} else if (c == '1') { // '1' key pressed?
|
|
Serial1.begin(115200); // set speed to 115200
|
|
Serial.println("Speed set to 115200");
|
|
} else if (c == '2') { // '2' key pressed?
|
|
Serial1.begin(250000); // set speed to 250000
|
|
Serial.println("Speed set to 250000");
|
|
} else if (c == '3') { // '3' key pressed?
|
|
Serial1.begin(500000); // set speed to 500000
|
|
Serial.println("Speed set to 500000");
|
|
} else if (c == '~') { // '~` key pressed?
|
|
// send "bridge shutdown" command
|
|
Serial1.write((uint8_t *)"\xff\0\0\x05XXXXX\x7f\xf9", 11);
|
|
Serial.println("Sending bridge's shutdown command");
|
|
} else { // any other key pressed?
|
|
Serial1.write('~'); // write '~' to UART
|
|
Serial1.write(c); // write char to UART
|
|
}
|
|
commandMode = false; // in all cases exit from command mode
|
|
}
|
|
}
|
|
|
|
// copy from UART to USB-CDC
|
|
c = Serial1.read(); // read from UART
|
|
if (c != -1) { // got anything?
|
|
Serial.write(c); // write to USB-CDC
|
|
}
|
|
}
|