mirror of
https://github.com/arduino/Arduino.git
synced 2024-12-03 14:24:15 +01:00
151 lines
4.0 KiB
Plaintext
151 lines
4.0 KiB
Plaintext
/*
|
|
SCP1000 Barometric Pressure Sensor Display
|
|
|
|
Shows the output of a Barometric Pressure Sensor on a
|
|
Uses the SPI library. For details on the sensor, see:
|
|
http://www.sparkfun.com/commerce/product_info.php?products_id=8161
|
|
http://www.vti.fi/en/support/obsolete_products/pressure_sensors/
|
|
|
|
This sketch adapted from Nathan Seidle's SCP1000 example for PIC:
|
|
http://www.sparkfun.com/datasheets/Sensors/SCP1000-Testing.zip
|
|
|
|
Circuit:
|
|
SCP1000 sensor attached to pins 6, 7, 10 - 13:
|
|
DRDY: pin 6
|
|
CSB: pin 7
|
|
MOSI: pin 11
|
|
MISO: pin 12
|
|
SCK: pin 13
|
|
|
|
created 31 July 2010
|
|
by Tom Igoe
|
|
*/
|
|
|
|
// the sensor communicates using SPI, so include the library:
|
|
#include <SPI.h>
|
|
|
|
//Sensor's memory register addresses:
|
|
const int PRESSURE = 0x1F; //3 most significant bits of pressure
|
|
const int PRESSURE_LSB = 0x20; //16 least significant bits of pressure
|
|
const int TEMPERATURE = 0x21; //16 bit temperature reading
|
|
|
|
// pins used for the connection with the sensor
|
|
// the other you need are controlled by the SPI library):
|
|
const int dataReadyPin = 6;
|
|
const int chipSelectPin = 7;
|
|
|
|
void setup() {
|
|
Serial.begin(9600);
|
|
|
|
// start the SPI library:
|
|
SPI.begin();
|
|
|
|
// initalize the data ready and chip select pins:
|
|
pinMode(dataReadyPin, INPUT);
|
|
pinMode(chipSelectPin, OUTPUT);
|
|
|
|
//Configure SCP1000 for low noise configuration:
|
|
writeRegister(0x02, 0x2D);
|
|
writeRegister(0x01, 0x03);
|
|
writeRegister(0x03, 0x02);
|
|
// give the sensor time to set up:
|
|
delay(100);
|
|
}
|
|
|
|
void loop() {
|
|
//Select High Resolution Mode
|
|
writeRegister(0x03, 0x0A);
|
|
|
|
// don't do anything until the data ready pin is high:
|
|
if (digitalRead(dataReadyPin) == HIGH) {
|
|
//Read the temperature data
|
|
int tempData = readRegister(0x21, 2);
|
|
|
|
// convert the temperature to celsius and display it:
|
|
float realTemp = (float)tempData / 20.0;
|
|
Serial.print("Temp[C]=");
|
|
Serial.print(realTemp);
|
|
|
|
|
|
//Read the pressure data highest 3 bits:
|
|
byte pressure_data_high = readRegister(0x1F, 1);
|
|
pressure_data_high &= 0b00000111; //you only needs bits 2 to 0
|
|
|
|
//Read the pressure data lower 16 bits:
|
|
unsigned int pressure_data_low = readRegister(0x20, 2);
|
|
//combine the two parts into one 19-bit number:
|
|
long pressure = ((pressure_data_high << 16) | pressure_data_low)/4;
|
|
|
|
// display the temperature:
|
|
Serial.println("\tPressure [Pa]=" + String(pressure));
|
|
}
|
|
}
|
|
|
|
//Sends a write command to SCP1000
|
|
|
|
void writeRegister(byte registerName, byte registerValue) {
|
|
// SCP1000 expects the reguster name in the upper 6 bits
|
|
// of the byte:
|
|
registerName <<= 2;
|
|
// command goes in the lower two bits:
|
|
registerName |= 0b00000010; //Write command
|
|
|
|
// take the chip select low to select the device:
|
|
digitalWrite(chipSelectPin, LOW);
|
|
|
|
SPI.transfer(registerName); //Send register location
|
|
SPI.transfer(registerValue); //Send value to record into register
|
|
|
|
// take the chip select high to de-select:
|
|
digitalWrite(chipSelectPin, HIGH); //Select SPI device
|
|
}
|
|
|
|
|
|
//Read register from the SCP1000:
|
|
unsigned int readRegister(byte registerName, int numBytes) {
|
|
byte inByte = 0; // incoming from the SPI read
|
|
unsigned int result = 0; // result to return
|
|
|
|
// SCP1000 expects the reguster name in the upper 6 bits
|
|
// of the byte:
|
|
registerName <<= 2;
|
|
// command goes in the lower two bits:
|
|
registerName &= 0b11111100; //Read command
|
|
|
|
// take the chip select low to select the device:
|
|
digitalWrite(chipSelectPin, LOW);
|
|
// send the device the register you want to read:
|
|
int command = SPI.transfer(registerName);
|
|
// send a value of 0 to read the forst byte returned:
|
|
inByte = SPI.transfer(0x00);
|
|
|
|
// if there's more than one byte returned,
|
|
// shift the first byte then get the second byte:
|
|
switch(numBytes) {
|
|
case 1:
|
|
result = inByte;
|
|
break;
|
|
case 2:
|
|
result = inByte << 8;
|
|
inByte = SPI.transfer(0x00);
|
|
result = result |inByte;
|
|
break;
|
|
}
|
|
// take the chip select high to de-select:
|
|
digitalWrite(chipSelectPin, HIGH);
|
|
// return the result:
|
|
return(result);
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|