From 770d1bb1f03dea74ca706cf135b0aeddad89cfed Mon Sep 17 00:00:00 2001
From: goodtft <goodtft@163.com>
Date: Thu, 4 Jul 2019 16:29:23 +0800
Subject: [PATCH] Update config-noobs-nomal.txt

---
 boot/config-noobs-nomal.txt | 128 ++++++++++++++++++------------------
 1 file changed, 64 insertions(+), 64 deletions(-)

diff --git a/boot/config-noobs-nomal.txt b/boot/config-noobs-nomal.txt
index 41efe4f..52f2b07 100755
--- a/boot/config-noobs-nomal.txt
+++ b/boot/config-noobs-nomal.txt
@@ -1,67 +1,67 @@
-# For more options and information see
-# http://rpf.io/configtxt
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-#hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-#dtparam=i2c_arm=on
-#dtparam=i2s=on
-#dtparam=spi=on
-
-# Uncomment this to enable the lirc-rpi module
-#dtoverlay=lirc-rpi
-
-# Additional overlays and parameters are documented /boot/overlays/README
-
-# Enable audio (loads snd_bcm2835)
-dtparam=audio=on
-
-[pi4]
-# Enable DRM VC4 V3D driver on top of the dispmanx display stack
-dtoverlay=vc4-fkms-v3d
-max_framebuffers=2
-
-[all]
-#dtoverlay=vc4-fkms-v3d
+# For more options and information see
+# http://rpf.io/configtxt
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+#hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+#dtparam=i2c_arm=on
+#dtparam=i2s=on
+#dtparam=spi=on
+
+# Uncomment this to enable the lirc-rpi module
+#dtoverlay=lirc-rpi
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+[pi4]
+# Enable DRM VC4 V3D driver on top of the dispmanx display stack
+#dtoverlay=vc4-fkms-v3d
+#max_framebuffers=2
+
+[all]
+#dtoverlay=vc4-fkms-v3d
 
 # NOOBS Auto-generated Settings:
 hdmi_force_hotplug=1