mirror of
https://github.com/goodtft/LCD-show.git
synced 2024-12-03 23:24:16 +01:00
124 lines
4.7 KiB
C++
124 lines
4.7 KiB
C++
#include "config.h"
|
|
|
|
#ifdef MZ61581
|
|
|
|
#include "spi.h"
|
|
|
|
#include <memory.h>
|
|
#include <stdio.h>
|
|
|
|
void InitMZ61581()
|
|
{
|
|
// If a Reset pin is defined, toggle it briefly high->low->high to enable the device. Some devices do not have a reset pin, in which case compile with GPIO_TFT_RESET_PIN left undefined.
|
|
#if defined(GPIO_TFT_RESET_PIN) && GPIO_TFT_RESET_PIN >= 0
|
|
printf("Resetting display at reset GPIO pin %d\n", GPIO_TFT_RESET_PIN);
|
|
SET_GPIO_MODE(GPIO_TFT_RESET_PIN, 1);
|
|
SET_GPIO(GPIO_TFT_RESET_PIN);
|
|
usleep(120 * 1000);
|
|
CLEAR_GPIO(GPIO_TFT_RESET_PIN);
|
|
usleep(120 * 1000);
|
|
SET_GPIO(GPIO_TFT_RESET_PIN);
|
|
usleep(120 * 1000);
|
|
#endif
|
|
|
|
// Do the initialization with a very low SPI bus speed, so that it will succeed even if the bus speed chosen by the user is too high.
|
|
spi->clk = 34;
|
|
__sync_synchronize();
|
|
|
|
BEGIN_SPI_COMMUNICATION();
|
|
{
|
|
// Reverse engineered with logic analyzer, not sure what these mean. If you have a data sheet for MZ61581, please send it my way.
|
|
SPI_TRANSFER(0xB0, 0x00);
|
|
SPI_TRANSFER(0xB3, 0x02, 0x00, 0x00, 0x00);
|
|
SPI_TRANSFER(0xC0, 0x13, 0x3B, 0x00, 0x02, 0x00, 0x01, 0x00, 0x43);
|
|
SPI_TRANSFER(0xC1, 0x08, 0x16, 0x08, 0x08);
|
|
SPI_TRANSFER(0xC4, 0x11, 0x07, 0x03, 0x03);
|
|
SPI_TRANSFER(0xC6, 0x00);
|
|
SPI_TRANSFER(0xC8, 0x03, 0x03, 0x13, 0x5C, 0x03, 0x07, 0x14, 0x08, 0x00, 0x21, 0x08, 0x14, 0x07, 0x53, 0x0C, 0x13, 0x03, 0x03, 0x21, 0x00);
|
|
SPI_TRANSFER(0x35, 0x00);
|
|
SPI_TRANSFER(0x44, 0x00, 0x01);
|
|
SPI_TRANSFER(0xD0, 0x07, 0x07, 0x1D, 0x03);
|
|
SPI_TRANSFER(0xD1, 0x03, 0x30, 0x10);
|
|
SPI_TRANSFER(0xD2, 0x03, 0x14, 0x04);
|
|
|
|
// The following coincide with e.g. ILI9341.
|
|
|
|
SPI_TRANSFER(0x3A/*COLMOD: Pixel Format Set*/, 0x55/*DPI=16bits/pixel,DBI=16bits/pixel*/);
|
|
|
|
#define MADCTL_BGR_PIXEL_ORDER (1<<3)
|
|
#define MADCTL_ROW_COLUMN_EXCHANGE (1<<5)
|
|
#define MADCTL_COLUMN_ADDRESS_ORDER_SWAP (1<<6)
|
|
#define MADCTL_ROW_ADDRESS_ORDER_SWAP (1<<7)
|
|
#define MADCTL_ROTATE_180_DEGREES (MADCTL_COLUMN_ADDRESS_ORDER_SWAP | MADCTL_ROW_ADDRESS_ORDER_SWAP)
|
|
|
|
uint8_t madctl = MADCTL_COLUMN_ADDRESS_ORDER_SWAP;
|
|
#ifndef DISPLAY_SWAP_BGR
|
|
madctl |= MADCTL_BGR_PIXEL_ORDER;
|
|
#endif
|
|
#if defined(DISPLAY_FLIP_ORIENTATION_IN_HARDWARE)
|
|
madctl |= MADCTL_ROW_COLUMN_EXCHANGE;
|
|
#endif
|
|
#ifdef DISPLAY_ROTATE_180_DEGREES
|
|
madctl ^= MADCTL_ROTATE_180_DEGREES;
|
|
#endif
|
|
SPI_TRANSFER(0x36/*MADCTL: Memory Access Control*/, madctl);
|
|
|
|
SPI_TRANSFER(0x11/*Sleep Out*/);
|
|
usleep(300 * 1000);
|
|
SPI_TRANSFER(0x29/*Display ON*/);
|
|
SPI_TRANSFER(0x2C);
|
|
|
|
// TONTEC_MZ61581 has backlight active when backlight GPIO is low, and at boot, it seems to be disabled, so always need to enable it.
|
|
#if defined(GPIO_TFT_BACKLIGHT) && (defined(BACKLIGHT_CONTROL) || defined(TONTEC_MZ61581))
|
|
printf("Setting TFT backlight on at pin %d\n", GPIO_TFT_BACKLIGHT);
|
|
SET_GPIO_MODE(GPIO_TFT_BACKLIGHT, 0x01); // Set backlight pin to digital 0/1 output mode (0x01) in case it had been PWM controlled
|
|
CLEAR_GPIO(GPIO_TFT_BACKLIGHT); // And turn the backlight on. MZ61581 backlight is on when the Backlight GPIO pin is 0.
|
|
#endif
|
|
|
|
ClearScreen();
|
|
}
|
|
#ifndef USE_DMA_TRANSFERS // For DMA transfers, keep SPI CS & TA active.
|
|
END_SPI_COMMUNICATION();
|
|
#endif
|
|
|
|
// And speed up to the desired operation speed finally after init is done.
|
|
usleep(10 * 1000); // Delay a bit before restoring CLK, or otherwise this has been observed to cause the display not init if done back to back after the clear operation above.
|
|
spi->clk = SPI_BUS_CLOCK_DIVISOR;
|
|
}
|
|
|
|
void TurnDisplayOff()
|
|
{
|
|
#if defined(GPIO_TFT_BACKLIGHT) && defined(BACKLIGHT_CONTROL)
|
|
SET_GPIO_MODE(GPIO_TFT_BACKLIGHT, 0x01); // Set backlight pin to digital 0/1 output mode (0x01) in case it had been PWM controlled
|
|
SET_GPIO(GPIO_TFT_BACKLIGHT); // And turn the backlight off.
|
|
#endif
|
|
#if 0
|
|
QUEUE_SPI_TRANSFER(0x28/*Display OFF*/);
|
|
QUEUE_SPI_TRANSFER(0x10/*Enter Sleep Mode*/);
|
|
usleep(120*1000); // Sleep off can be sent 120msecs after entering sleep mode the earliest, so synchronously sleep here for that duration to be safe.
|
|
#endif
|
|
// printf("Turned display OFF\n");
|
|
}
|
|
|
|
void TurnDisplayOn()
|
|
{
|
|
#if 0
|
|
QUEUE_SPI_TRANSFER(0x11/*Sleep Out*/);
|
|
usleep(120 * 1000);
|
|
QUEUE_SPI_TRANSFER(0x29/*Display ON*/);
|
|
#endif
|
|
#if defined(GPIO_TFT_BACKLIGHT) && defined(BACKLIGHT_CONTROL)
|
|
SET_GPIO_MODE(GPIO_TFT_BACKLIGHT, 0x01); // Set backlight pin to digital 0/1 output mode (0x01) in case it had been PWM controlled
|
|
CLEAR_GPIO(GPIO_TFT_BACKLIGHT); // And turn the backlight on.
|
|
#endif
|
|
// printf("Turned display ON\n");
|
|
}
|
|
|
|
void DeinitSPIDisplay()
|
|
{
|
|
ClearScreen();
|
|
SPI_TRANSFER(/*Display OFF*/0x28);
|
|
}
|
|
|
|
#endif
|