1
0
mirror of https://bitbucket.org/librepilot/librepilot.git synced 2024-12-04 12:24:11 +01:00
LibrePilot/flight/board_hw_defs/ahrs/board_hw_defs.c

352 lines
8.3 KiB
C
Raw Normal View History

#include <pios_config.h>
#if defined(PIOS_INCLUDE_LED)
#include <pios_led_priv.h>
static const struct pios_led pios_leds[] = {
[PIOS_LED_HEARTBEAT] = {
.pin = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_3,
.GPIO_Mode = GPIO_Mode_Out_PP,
.GPIO_Speed = GPIO_Speed_50MHz,
},
},
},
};
static const struct pios_led_cfg pios_led_cfg = {
.leds = pios_leds,
.num_leds = NELEMENTS(pios_leds),
};
#endif /* PIOS_INCLUDE_LED */
#if defined(PIOS_INCLUDE_SPI)
#include <pios_spi_priv.h>
/* OP Interface
*
* NOTE: Leave this declared as const data so that it ends up in the
* .rodata section (ie. Flash) rather than in the .bss section (RAM).
*/
void PIOS_SPI_op_irq_handler(void);
void DMA1_Channel5_IRQHandler() __attribute__ ((alias("PIOS_SPI_op_irq_handler")));
void DMA1_Channel4_IRQHandler() __attribute__ ((alias("PIOS_SPI_op_irq_handler")));
static const struct pios_spi_cfg pios_spi_op_cfg = {
.regs = SPI2,
.init = {
.SPI_Mode = SPI_Mode_Slave,
.SPI_Direction = SPI_Direction_2Lines_FullDuplex,
.SPI_DataSize = SPI_DataSize_8b,
.SPI_NSS = SPI_NSS_Hard,
.SPI_FirstBit = SPI_FirstBit_MSB,
.SPI_CRCPolynomial = 7,
.SPI_CPOL = SPI_CPOL_High,
.SPI_CPHA = SPI_CPHA_2Edge,
},
.use_crc = TRUE,
.dma = {
.ahb_clk = RCC_AHBPeriph_DMA1,
.irq = {
.flags =
(DMA1_FLAG_TC4 | DMA1_FLAG_TE4 | DMA1_FLAG_HT4 |
DMA1_FLAG_GL4),
.init = {
.NVIC_IRQChannel = DMA1_Channel4_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.channel = DMA1_Channel4,
.init = {
.DMA_PeripheralBaseAddr =
(uint32_t) & (SPI2->DR),
.DMA_DIR = DMA_DIR_PeripheralSRC,
.DMA_PeripheralInc =
DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize =
DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize =
DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_M2M = DMA_M2M_Disable,
},
},
.tx = {
.channel = DMA1_Channel5,
.init = {
.DMA_PeripheralBaseAddr =
(uint32_t) & (SPI2->DR),
.DMA_DIR = DMA_DIR_PeripheralDST,
.DMA_PeripheralInc =
DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize =
DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize =
DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_M2M = DMA_M2M_Disable,
},
},
},
.ssel = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_12,
.GPIO_Speed = GPIO_Speed_10MHz,
.GPIO_Mode = GPIO_Mode_IN_FLOATING,
},
},
.sclk = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_13,
.GPIO_Speed = GPIO_Speed_10MHz,
.GPIO_Mode = GPIO_Mode_IN_FLOATING,
},
},
.miso = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_14,
.GPIO_Speed = GPIO_Speed_10MHz,
.GPIO_Mode = GPIO_Mode_AF_PP,
},
},
.mosi = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_15,
.GPIO_Speed = GPIO_Speed_10MHz,
.GPIO_Mode = GPIO_Mode_IN_FLOATING,
},
},
};
uint32_t pios_spi_op_id;
void PIOS_SPI_op_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_SPI_IRQ_Handler(pios_spi_op_id);
}
#endif /* PIOS_INCLUDE_SPI */
#if defined(PIOS_INCLUDE_ADC)
/*
* ADC system
*/
#include "pios_adc_priv.h"
extern void PIOS_ADC_handler(void);
void DMA1_Channel1_IRQHandler() __attribute__ ((alias("PIOS_ADC_handler")));
// Remap the ADC DMA handler to this one
static const struct pios_adc_cfg pios_adc_cfg = {
.dma = {
.ahb_clk = RCC_AHBPeriph_DMA1,
.irq = {
.flags = (DMA1_FLAG_TC1 | DMA1_FLAG_TE1 | DMA1_FLAG_HT1 | DMA1_FLAG_GL1),
.init = {
.NVIC_IRQChannel = DMA1_Channel1_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.channel = DMA1_Channel1,
.init = {
.DMA_PeripheralBaseAddr = (uint32_t) & ADC1->DR,
.DMA_DIR = DMA_DIR_PeripheralSRC,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Word,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Word,
.DMA_Mode = DMA_Mode_Circular,
.DMA_Priority = DMA_Priority_High,
.DMA_M2M = DMA_M2M_Disable,
},
}
},
.half_flag = DMA1_IT_HT1,
.full_flag = DMA1_IT_TC1,
};
struct pios_adc_dev pios_adc_devs[] = {
{
.cfg = &pios_adc_cfg,
.callback_function = NULL,
},
};
uint8_t pios_adc_num_devices = NELEMENTS(pios_adc_devs);
void PIOS_ADC_handler() {
PIOS_ADC_DMA_Handler();
}
#endif /* PIOS_INCLUDE_ADC */
#if defined(PIOS_INCLUDE_USART)
#include <pios_usart_priv.h>
/*
* AUX USART
*/
static const struct pios_usart_cfg pios_usart_aux_cfg = {
.regs = USART3,
.init = {
.USART_BaudRate = 230400,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl =
USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx | USART_Mode_Tx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART3_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_IPU,
},
},
.tx = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF_PP,
},
},
};
#endif /* PIOS_INCLUDE_USART */
#if defined(PIOS_INCLUDE_COM)
#include <pios_com_priv.h>
#endif /* PIOS_INCLUDE_COM */
#if defined(PIOS_INCLUDE_I2C)
#include <pios_i2c_priv.h>
/*
* I2C Adapters
*/
void PIOS_I2C_main_adapter_ev_irq_handler(void);
void PIOS_I2C_main_adapter_er_irq_handler(void);
void I2C1_EV_IRQHandler()
__attribute__ ((alias("PIOS_I2C_main_adapter_ev_irq_handler")));
void I2C1_ER_IRQHandler()
__attribute__ ((alias("PIOS_I2C_main_adapter_er_irq_handler")));
static const struct pios_i2c_adapter_cfg pios_i2c_main_adapter_cfg = {
.regs = I2C1,
.init = {
.I2C_Mode = I2C_Mode_I2C,
.I2C_OwnAddress1 = 0,
.I2C_Ack = I2C_Ack_Enable,
.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit,
.I2C_DutyCycle = I2C_DutyCycle_2,
.I2C_ClockSpeed = 200000, /* bits/s */
},
.transfer_timeout_ms = 50,
.scl = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_10MHz,
.GPIO_Mode = GPIO_Mode_AF_OD,
},
},
.sda = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Speed = GPIO_Speed_10MHz,
.GPIO_Mode = GPIO_Mode_AF_OD,
},
},
.event = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C1_EV_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.error = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C1_ER_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
uint32_t pios_i2c_main_adapter_id;
void PIOS_I2C_main_adapter_ev_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_EV_IRQ_Handler(pios_i2c_main_adapter_id);
}
void PIOS_I2C_main_adapter_er_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_ER_IRQ_Handler(pios_i2c_main_adapter_id);
}
#endif /* PIOS_INCLUDE_I2C */
#if defined(PIOS_ENABLE_DEBUG_PINS)
static const struct stm32_gpio pios_debug_pins[] = {
{
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_IN_FLOATING,
},
},
{
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_Out_PP,
},
},
};
#endif /* PIOS_ENABLE_DEBUG_PINS */