PIOS_Flash_Jedec_EraseChip is called during early
init when the table_magic has changed. This call
happens on CC/CC3D prior to the OS being initialized
so it is not OK to call vTaskDelay() yet.
This was leading to boards locking up (no flashing blue
LED) immediately after jumping to the application when
the table_magic had changed or was being init'd for the
very first time.
The module can be configured to enable what's needed from board voltage, battery voltage and battery current measurement.
In GCS the POWER box in system healt will show alarm related to the supply voltage to the board.
If a power warning/critical alarm is raised, the warning condition is left even if the board voltage return to an acceptable value.
Conflicts:
ground/openpilotgcs/share/openpilotgcs/diagrams/default/system-health.svg
shared/uavobjectdefinition/systemalarms.xml
flash so it says completed. However, it still blocks the system for a long
time. During an erase the heartbeat will flash at 10 Hz to indicate what's
happening.
This still blocks telemetry even after lowering hte system priority (and there
is a vTaskDelay) which makes me think that the SPI bus being locked is blocking
Sensors or somethign else. This should not be permited when the system is
armed.
The reason the system locks up during the erase is that the file system
operations occur within the event dispatcher thread. It is very bad practice
for anything to block this (i.e. callbacks should never take very long). We
should probably move the object persistence handling into the system thread or
something but that can be a separate issue.
The bootloader needs to understand whether the USB cable
is connected. The HID and CDC drivers need to know if
the cable is connected _and_ the device has been enumerated
already. Separate these two concepts in the API.
Combining these was resulting in the BL not properly
detecting that the cable was plugged in, and trying to boot
the firmware image immediately. This effectively bricked
the board if you ever had an invalid firmware image.
It also happens to be the case that the BU images automatically
invalidate themselves after updating the BL so they don't run
again. The cable detect bug + this intended behaviour of the
BU image resulted in a bricked board after upgrading the BL.
USB device was being accessed prior to being initialized.
This resulted in a hard-fault or NMI when using any endpoint
beyond 0 or 1 which are init'ed by the BL. This broke VCP which
is on endpoint 2 (control) and 3 (data).
This bug was introduced in 5ad37e69 which stopped checking the
transfer_possible variable.
Some versions of Windows will ignore the USB device serial number
if the string is not delivered with LANGID = English US 0x0409.
This is true regardless of the configured locale of the machine.
BL images now always use hid-only.
FW images can use hid-only or hid+vcp but this is selected
ONLY at compile time based on whether PIOS_INCLUDE_USB_CDC
is defined.
CC uses HID+VCP by default now.
Now that we have a USB descriptor for HID+VCP that works
on Ubuntu 11.10, MacOS 10.7.3, Win7-SP1-32bit,
WinXP-SP3-32bit, Win7-SP1-64bit.
VCP is known to not work on WinXP without service pack 3.
were consuming lots of memory. Probably should make a simple adc version that
just queries the line when needed since we are only using this data at 500 ms.
However, the accumulator scheme in place is quite good for averaging over time.
The bootloader has been enabling pull-ups on all GPIO
pins during early init. These pull-ups are disabled
immediately before jumping to the firmware. This transition
results in all servos seeing a wide pulse as the board
resets making them jerk sideways aggresively and then snap
back to neutral.
All channels at max when using the FrSKY 4ch D4FR in PPM
mode results in the frame pulse shrinking well below our
threshold of 3800us and we lose frame.
With all 8 channels at max, the frame pulse becomes
indistinguishable from the other channels. Using all 8
channels with the FrSKY in PPM mode is NOT recommended
even after this change.
Recommend using at most 7 active channels in this mode so
we can still find the frame pulse.
Now that we have a USB descriptor for HID+VCP that works
on Ubuntu 11.10, MacOS 10.7.3, Win7-SP1-32bit,
WinXP-SP3-32bit, Win7-SP1-64bit.
VCP will is known to not work on WinXP without service pack 3.
The bootloader has been enabling pull-ups on all GPIO
pins during early init. These pull-ups are disabled
immediately before jumping to the firmware. This transition
results in all servos seeing a wide pulse as the board
resets making them jerk sideways aggresively and then snap
back to neutral.
All channels at max when using the FrSKY 4ch D4FR in PPM
mode results in the frame pulse shrinking well below our
threshold of 3800us and we lose frame.
With all 8 channels at max, the frame pulse becomes
indistinguishable from the other channels. Using all 8
channels with the FrSKY in PPM mode is NOT recommended
even after this change.
Recommend using at most 7 active channels in this mode so
we can still find the frame pulse.
