yaw angle crosses the zero-360 mark, beware.
You can disable yaw stabilization by setting all PID gains to zero for yaw.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1828 ebee16cc-31ac-478f-84a7-5cbb03baadba
and removed the unused field from actuator settings (old setting time and all
the aircraft specific stuff).
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1820 ebee16cc-31ac-478f-84a7-5cbb03baadba
update since now drive by events. This means StabilizationSettings object
changing so write down your settings.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1819 ebee16cc-31ac-478f-84a7-5cbb03baadba
THIS MEANS YOU MUST RETUNE YOUR PID LOOP IF YOU'RE FLYING WITH IT
Alternatively divide Kd by 1000 and multiply Ki by 1000
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1782 ebee16cc-31ac-478f-84a7-5cbb03baadba
Flight: Create PositionDesired (the active waypoint) UAVObject and make the FlightSituationActual no update since it not used.
Flight: New velocity desired object that passes information between the look computing the desired velocity and the PID loop to get it (updated at different rates)
UAVObjects/PositionActual: Remove unused GPS fields
UAVObjects/PositionActual VelocityActual: Split the velocity into a separate object. ALso make sure all the information telemetered around is in cm to avoid using floats.
UAVObject/GuidanceSettings: New guidance settings object for the guidance module
Flight/Posix: Add the new objects to the Posix sim
Flight/Guidance: Computes a desired velocity based on position error than runs a PID loop to control roll and pitch to achieve that velocity. All distances are in cm, and updated the PositionActual fields to reflect this and use int32.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1760 ebee16cc-31ac-478f-84a7-5cbb03baadba
determine retransmitting calibration, home location and such.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1755 ebee16cc-31ac-478f-84a7-5cbb03baadba
Calibration should take less time now too (using second moments to estimate
variance in one pass). Now need to change to multiple messages to get the
calibration in to keep the request message size minimal. Also currently
running sensor calibrate doesn't store the gyro bias so if you want to use this
you'll have to tweak it manually. I'll fix that step tomorrow.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1741 ebee16cc-31ac-478f-84a7-5cbb03baadba
The system settings UAVObject is updated, you will have to recompile your firmware. If you want to take a look and let me know, please do!
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1737 ebee16cc-31ac-478f-84a7-5cbb03baadba
Removing some Experimental and Incomplete Modules and their UAVObjects not suited for 1.0
- they will be moved into an experimental branch:
Navigation : experimental code only
FlightSituation: experimental code only
Guidance : preliminary draft - possibly to be replaced by peabody124 position hold code if finished in time.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1729 ebee16cc-31ac-478f-84a7-5cbb03baadba
Creating GuidanceModule together with PositionDesired UAVObject (as discussed),
so dschin and me can work on it :-)
Will compile and (on sim_posix) execute, but PID logic is yet untested and preliminary.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1722 ebee16cc-31ac-478f-84a7-5cbb03baadba
This is functionally the same as having a heading hold gyro in hardware.
Code is copied from the simple stabilisation routine and is a bit rough at the minute, but initial testing looks good.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1670 ebee16cc-31ac-478f-84a7-5cbb03baadba
The EOC EXTI interrupt configuration was incorrectly
pointing at GPIOG pin 8 rather than GPIOC pin 15.
This was preventing the EOC interrupt from working
properly.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1626 ebee16cc-31ac-478f-84a7-5cbb03baadba
