1
0
mirror of https://bitbucket.org/librepilot/librepilot.git synced 2024-12-11 19:24:10 +01:00
Commit Graph

423 Commits

Author SHA1 Message Date
James Cotton
11ac0707da BMA180: Reset BMA180 chip at reconfiguration. 2011-08-17 06:49:56 -05:00
James Cotton
35eef66bfe OP-557: Add a UAVO access method to erase the entire flash chip. Normally not
needed by users because if too much changes I change the FS magic and trigger a
wipe.

Possibly the erase should require a particular "magic" object id value to
execute?  This would make it harder to do manually through UAVOs though.
2011-08-15 10:33:27 -05:00
James Cotton
86b652bbab Merge branch 'next' into camera_stabilization 2011-08-14 18:07:57 -05:00
zedamota
e736b17cc4 Merge remote-tracking branch 'remotes/origin/next' into GCS_ChangesToUI-RuntimeCFG
Conflicts:
	ground/openpilotgcs/src/plugins/config/config_cc_hw_widget.cpp
	ground/openpilotgcs/src/plugins/config/configgadgetwidget.h
	ground/openpilotgcs/src/plugins/config/configstabilizationwidget.cpp
2011-08-14 15:48:16 +01:00
James Cotton
80c2d45d93 Fix the BMP085 interrupt handler and get it producing data. Driver needs some
work to abstract away the actual calculation of altitude from pressure and
temperature.
2011-08-13 20:49:07 -05:00
James Cotton
a2b76adc33 Attitude: Do not start attitude estimation until accel data appears. This
fixes the NaN when AttitudeSettings not available.
2011-08-13 18:53:42 -05:00
James Cotton
62f51fc92d Some improvements to the HMC5883 driver. Still getting funny values but I
suspect the chip at this point.
2011-08-13 11:20:32 -05:00
James Cotton
f82e5dde33 Fix the EXTI IRQ handlers 2011-08-13 07:13:21 -05:00
James Cotton
1d1f351233 Pios Delay: Add function for measuring time difference between two cycle counts 2011-08-12 04:29:53 -05:00
James Cotton
f247112090 PiOS F2: Move IMU3000 to device dependent :(. Now they all are. Need to
abstract as much as possible out since init is almost identicalc and protocol
COULD be device independent.
2011-08-12 03:38:45 -05:00
James Cotton
8c1dd7b929 Make BMP085 driver device dependent and update to new driver style. 2011-08-12 03:38:45 -05:00
James Cotton
9d76efa2aa Move BMA180 driver to common architecture style. 2011-08-12 03:38:45 -05:00
James Cotton
1dc08e5cf7 F2 PiOS: Small fix to hmc5883 driver 2011-08-12 03:38:44 -05:00
James Cotton
6310f46705 HMC5883: Update driver for F2. Move to STM32F2xx directory since it is device
dependent.  Abstract configuration out of board.h file into a standard board.c
structure.
2011-08-12 02:26:51 -05:00
James Cotton
9c7799dfe6 UAVObject Init: Get rid of deprecated linker init code 2011-08-10 22:48:42 -05:00
James Cotton
0c2c48bee6 F2 PiOS: More changes for spi to work (not completed) 2011-08-09 12:59:10 -05:00
James Cotton
a097ff784b F2 PiOS: Getting the I2C driver working again (copying changes from Zippe,
thanks again man!)
2011-08-09 12:58:46 -05:00
James Cotton
479ba7c21f OP-378 INS: Continue getting F2 INS to compile 2011-08-08 08:36:40 -05:00
James Cotton
d1c9ac0705 PiOS F2: Commit the F2 port of PiOS from Zippe. Thanks for doing all the hard
work man :-D
2011-08-06 19:36:56 -05:00
James Cotton
0bba13a0e9 Merge branch 'next' into ins
Conflicts:
	flight/INS/Makefile
	flight/INS/pios_board.c
	flight/Modules/Altitude/altitude.c
	flight/PiOS/Boards/STM3210E_INS.h
	flight/PiOS/STM32F10x/link_STM3210E_INS_BL_sections.ld
	flight/PiOS/STM32F10x/link_STM3210E_INS_HD_BL.ld
	flight/PiOS/STM32F10x/link_STM3210E_INS_HD_NB.ld
	flight/PiOS/STM32F10x/link_STM3210E_INS_memory.ld
	flight/PiOS/STM32F10x/link_STM3210E_INS_sections.ld
	flight/Project/OpenPilotOSX/OpenPilotOSX.xcodeproj/project.pbxproj
2011-08-06 17:25:56 -05:00
sambas
1e67b5e3b5 DSMx_binder, hw setting 0 disabled, 1-10 bind pulses. Manual disable after successful bind. Only for flexiport. 2011-08-06 22:16:47 +03:00
Stacey Sheldon
06cdeb7b61 rcvr: support multiple simultaneous receivers
Now also supports multiple instances of the Spektrum driver.
These are configured as Spektrum1 and Spektrum2.
2011-08-02 01:22:04 -04:00
Stacey Sheldon
829b8b83f6 rcvr: Add GCS receiver driver for rcvr via telemetry
This allows the GCS to emulate a receiver device via the
telemetry link.

Select "GCS" as your input type in the manualcontrol config
screen and calibrate it as normal.

Note: The expected values for the channels are in microseconds
      just like a PWM or PPM input device.  The channel values
      are validated against minimum/maximum pulse lengths just
      like normal receivers.
2011-08-02 01:22:04 -04:00
Stacey Sheldon
c2fb0d8b43 com: allow run-time allocation of buffers 2011-07-29 15:33:14 -04:00
Stacey Sheldon
8b0415d905 bl: alternate stopwatch for small bootloaders
The small bootloaders (CC and PipX) are out of flash space
so their stopwatch implementation has been swapped out for
one based on the DELAY clock that takes about 500 bytes less
of code space.

Identical functionality is preserved.
2011-07-29 15:33:01 -04:00
Stacey Sheldon
5f8760a55c com: Move buffering out of USART/HID layer and into COM layer
This allows the spektrum and sbus receiver drivers to bind
directly to the usart layer using a properly exported API
rather than overriding the interrupt handler.

Bytes are now pushed directly from the usart layer into the
com layer without any buffering.  The com layer performs all
of the buffering.

A further benefit from this approach is that we can put all
blocking/non-blocking behaviour into the COM layer and not
in the underlying drivers.

Misc related changes:
 - Remove obsolete .handler field from irq configs
 - Adapt all users of PIOS_COM_* functions to new API
 - Fixup callers of PIOS_USB_HID_Init()
2011-07-27 19:45:38 -04:00
Mike Smith
df5569c758 Fix a stupid off-by-one that prevented this code from working.
Update to use 32-bit microsecond values.

Remove PIOS_DELAY_DiffuS per consensus (caller can do it easily themselves).

Update the core delay logic per Stac's suggestion to a version that is
resistant to various overflows.
2011-07-25 20:55:48 -07:00
Stacey Sheldon
6580462916 rcvr: specify drivers for groups of channels
Each channel was previously tracking a separate driver.
Now, channels are grouped within a channel group to save
RAM used for tracking and to better reflect how channels
are actually mapped.
2011-07-14 23:22:42 -04:00
Mathieu Rondonneau
612a439199 OP-423: simplify the MODULE_INITCALL macro and remove the ordering loops 2011-07-12 20:44:32 -07:00
Mathieu Rondonneau
d38f6167e3 OP-423:
Also reduce heap has it does not fit in SRAM anymore (not with current compiler).
(that's ok since if there is more space available, it will be reclaimed).

Merge branch 'master' into OP-423_Mathieu_Change_Init_To_Reduce_Memory_Footprint

Conflicts:
	flight/CopterControl/System/inc/pios_config.h
	flight/Modules/ManualControl/manualcontrol.c
2011-07-08 06:29:34 -07:00
Stacey Sheldon
2e8d3a9be3 clean up cut/paste cruft 2011-07-07 23:02:09 -04:00
Stacey Sheldon
1f004ee896 ppm: port PPM driver onto new CC driver layers
This is a port of a work-in-progress by Sambas onto
the new driver infrastructure needed for boot-time
configuration.

PPM and PWM still don't coexist in a build but this
is closer.
2011-07-07 22:27:57 -04:00
Mathieu Rondonneau
9b9b5a1367 OP-423: remove ';' at the end of macro 2011-07-05 19:44:54 -07:00
Stacey Sheldon
dbf7574946 bootcfg: use UAVobj to control boot-time HW config
This should mark an end to the compile-time selection of HW
configurations.

Minor changes in board initialization for all platforms:
 - Most config structs are marked static to prevent badly written
   drivers from directly referring to config data.
 - Adapt to changes in .irq fields in config data.
 - Adapt to changes in USART IRQ handling.

Major changes in board initialization for CC:
 - Use HwSettings UAVObj to decide which drivers to attach to
   the "main" port and the flexi port, and select the appropriate
   device configuration data.
 - HwSettings allows choosing between Disabled, Telemetry, SBUS,
   Spektrum,GPS, and I2C for each of the two ports.
 - Use ManualControlSettings.InputMode to init/configure the
   appropriate receiver module, and register its available rx channels
   with the PIOS_RCVR layer.  Can choose between PWM, Spektrum and PPM
   at board init time.  PPM driver is broken, and SBUS will work once
   it is added to this UAVObj as an option.
 - CC build now includes code for SBUS, Spektrum and PWM receivers in
   every firmware image.

PIOS_USART driver:
 - Now handles its own low-level IRQs internally
 - If NULL upper-level IRQ handler is bound in at board init time
   then rx/tx is satisfied by internal PIOS_USART buffered IO routines
   which are (typically) attached to the COM layer.
 - If an alternate upper-level IRQ handler is bound in at board init
   then that handler is called and expected to clear down the USART
   IRQ sources.  This is used by Spektrum and SBUS drivers.

PIOS_SBUS and PIOS_SPEKTRUM drivers:
 - Improved data/API hiding
 - No longer assume they know where their config data is stored which
   allows for boot-time alternate configurations for the driver.
 - Now registers an upper-level IRQ handlerwith the USART layer to
   decouple the driver from which USART it is actually attached to.
2011-07-05 22:03:25 -04:00
Stacey Sheldon
6415fc84a5 rtc: allow registration of callbacks on RTC tick
This separates the RTC device and interrupt handling
from the devices that rely on the tick notifications.

Drivers can now register tick notification functions
that will be called on each RTC tick event.
2011-07-05 22:03:25 -04:00
Stacey Sheldon
740b5f1584 rcvr: convert PWM, PPM, SBUS and Spektrum to use PIOS_RCVR
All receivers now fall under the same driver API provided
by pios_rcvr.c.

This is part of a larger sequence of commits that will
switch the receiver selection over to boot time dynamic
configuration via UAVObjects.
2011-07-05 22:03:25 -04:00
Stacey Sheldon
e77795dc28 rcvr: add generic driver API for receivers
Will be used to collapse PWM, PPM, Spektrum and SBUS so we
can choose between them at boot time instead of at compile time.
2011-07-05 22:02:47 -04:00
Mathieu Rondonneau
6683ce8570 OP-423: Make it more obvious that MODULE_TASKCREATE_ALL and MODULE_INITIALIZE_ALL are macro (for now):
- remove the ;
  - also encapsulate the macro by {} in his own scope.
2011-06-25 11:40:01 -07:00
Mathieu Rondonneau
de55c56427 OP-423: Change capital on macro to be uppercase for consistency. 2011-06-24 22:03:03 -07:00
Mathieu Rondonneau
0ff5e9a46f Merge branch 'master' into OP-423_Mathieu_Change_Init_To_Reduce_Memory_Footprint 2011-06-21 22:02:13 -07:00
Mathieu Rondonneau
fc1e3f574c OP-423: Split task create and module init in order to postpone task creation once the full heap is available.
Also implement some ordering (quite ugly still) in the module init and task creation order so we can decide which module to start/init first
and which module to start/init last.
This will be replaced/adapter with the uavobject list later (once it's implemented).
reserving some space for module init and task create parameters to customize module/task creation (this will be usefull once we get the list and customization from customer).

Changes have been made for OP and CC. Tested comped with CC,OP, sim_posix.
Only ran on bench with CC for couple of minutes (code increase expected but no dropping of stack which is good).

This gives task creation at the time wherethe all heap is available.
2011-06-19 22:35:40 -07:00
Oleg Semyonov
6272210df7 sbus: some code cleanup (no functional changes) 2011-06-19 14:30:13 +03:00
Oleg Semyonov
311902f1f2 sbus: implemented S.Bus stream decoding 2011-06-18 23:19:57 +03:00
Mathieu Rondonneau
65cf467ca4 OP-423: move the module initialize funtion into a specific section for OP and CC.
- create linker section for those <module>Initialize()
- later this list will incorporate parameters as well. (this probably will be more a OP feature to swap/remove/delete module on the fly.
- this is not done at compile time anymore by Makefile.
- this will allow us to have control on the module start at run-time (not implemented but build the ground for it).
- this simplify the startup (Part of code re-org).
- this change does not affect sim_posix and win32 (since they don't need that)
- ensure it's compiling for PiOS.posix
- port to PiOS.win32 but not tested (not compiled)
- tested on CC
- compile on OP.
- this free ~200 bytes.
- current avalable bytes (is we keep the same remaining bytes on the stack than before) is easily passed the 1.2Ko mark on CC with new gcc (4.5.2)
- this does not include init-reorg for each module (I still think more can be freed)
2011-06-16 22:13:19 -07:00
Oleg Semyonov
d8201ec45b sbus: provide a stub based on Spektrum driver (for CC only) 2011-06-15 22:35:21 +03:00
James Cotton
3e5d02cbaf OP-152: Abstract the CRC code out of uavtalk to allow it to be reused (PT -
feel free to test moving this to the hardware CRC unit)
2011-06-04 18:36:26 -05:00
James Cotton
524cdf7743 OP-378: Start of IMU3000 fifo reading code 2011-05-31 01:51:05 -05:00
James Cotton
b6a8293f69 OP-378: Get BMA180 interrupt working. Data gets pushed onto a fifo that is
pulled from in the INS code.
2011-05-30 03:40:51 -05:00
sambas
17fb31a7fa Spektrum rtc supervisor working, tested on CC and all outputs are activated. Needs review and testing before merge. 2011-05-29 14:52:22 +03:00
sambas
86d02e2d34 Merge branch 'master' of ssh://git.openpilot.org/OpenPilot into spektrum_rtc_supervisor 2011-05-29 10:40:17 +03:00
Stacey Sheldon
ac0eb3a5c7 Merge remote branch 'origin/stac_build-opf-image' 2011-05-26 21:29:53 -04:00
James Cotton
66b85acebd Merge branch 'bugfix-flight' 2011-05-26 20:07:58 -05:00
James Cotton
9ede84680e OP-378: Start working on IRQ driven BMA180 reading and also fixed the mag order 2011-05-26 13:57:41 -05:00
James Cotton
6e186bab35 Merge branch 'bugfix-flight' into OP-378_James_INS 2011-05-26 12:19:35 -05:00
James Cotton
0a60c5b57c Merge branch 'master' into OP-378_James_INS 2011-05-26 12:19:30 -05:00
James Cotton
4bc763dafc Extend PiOS DELAY to allow querying the time value in uS 2011-05-26 12:19:04 -05:00
James Cotton
74b9c58f39 Make sensors return data as int16 array instead of struct 2011-05-26 02:49:25 -05:00
Stacey Sheldon
8bd08e381a build: add support for EE bank on pipx boards
The pipxtreme boards use a sector of the on-board flash
for configuration storage.  Adjust the memory maps to
reflect this.

The board_info_blob is also extended to include the EE
bank definitions.  This should be used by the pipxtreme
firmware rather than determining it based on chip size.
2011-05-24 01:10:40 -04:00
James Cotton
50161b4ad8 OP-378: Continue updating BMA180 sensor driver. 2011-05-20 16:38:53 -05:00
James Cotton
5d78a68bee OP-378: Got BMA180 working. 2011-05-19 11:36:43 -05:00
James Cotton
3093d26cf4 OP-378: Update BMP085 driver for convention that 0 is success, < 0 is failure 2011-05-19 11:36:32 -05:00
James Cotton
750097ea73 OP-378: Small changes to get drivers working again. Fix I2C port for IMU3000
and change convention so that 0 is success, < 0 is error.
2011-05-18 23:35:45 -05:00
James Cotton
81b7fb6185 Merge branch 'master' into OP-378_James_INS 2011-05-18 12:50:29 -05:00
James Cotton
bdf862a712 PIOS/RTC: Add functions to get the rate. Also changed Start to Init to be more
consistent with pios.
2011-05-18 01:45:21 -05:00
Stacey Sheldon
575010169a build: add pios_board_info_blob struct to bootloader flash image
The board info blob is stored in the last 128 bytes of the
bootloader's flash bank.  You can access this data from the
application firmware like this:
  #include <pios_board_info.h>

  if (pios_board_info_blob.magic == PIOS_BOARD_INFO_BLOB_MAGIC) {
    /* Check some other fields */
  }

DO NOT link pios_board_info.c into your application firmware.
Only bootloaders should provide the content for the board info
structure.  The application firmware is only a user of the data.
2011-05-16 08:30:30 -04:00
James Cotton
7e6e7bb391 OP-499 OP-216: Simple list of objects saved in flash to prevent objId
collision.  Note, this will wipe ALL your settings.
2011-05-14 14:05:02 -05:00
Stacey Sheldon
2301600f11 Make missing definitions for essential macros more obvious 2011-05-07 18:05:50 -04:00
sambas
d61f3d4d94 Merge branch 'OP-378_CheBuzz_INS' of ssh://git.openpilot.org/OpenPilot into OP-378_CheBuzz_INS 2011-05-07 18:26:12 +03:00
Corvus Corax
5d952f81e3 PIOS: BL_HELPER: refactored function names 2011-04-23 21:11:17 +02:00
Corvus Corax
357bc369db PIOS: Bootloader Helper functions should sit in HAL, not duplicated in every single architecture. 2011-04-23 19:40:41 +02:00
Corvus Corax
192e31986d PIOS, Modules/FirmwareIAP: Use correct HAL for CPU serial 2011-04-23 18:30:32 +02:00
David Buzz Carlson
876ca3044c Added EKF code. Most of this was bulk copy and paste from the AHRS, so a lot of verification needs to take place. Grabbing sensor data remains untested. 2011-04-20 03:37:50 -07:00
chebuzz
06443b4281 OP-378 - OP/INS - Add initial support for INS. HMC5883, BMP085, BMA180, IMU300 all added. Throrough verification has not been done on any of them. main() simply calls self-test functions on all of the hardware.
AHRS_comms still needs to be implemented.  INS/GPS functionality still needs to be implemented.  Double-check of the new drivers still needs to be done.


git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@3162 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-04-14 12:46:39 +00:00
chebuzz
195e93c0d6 OP-377 PiOS/BMP085 - Update BMP085 driver to be FreeRTOS agnostic. This is required since new INS does not run FreeRTOS.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@3160 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-04-14 09:46:23 +00:00
edouard
aa097ec400 OP-339 Update USB descriptors on CopterControl and OpenPilot to reflect the new convention.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@3015 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-03-09 07:21:01 +00:00
sambas
0eeacb44bd PPM driver for OP, first test
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@3007 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-03-08 18:08:13 +00:00
FredericG
35475820ad 2 new PIOS_DEBUG functions to output a value on the debug-pins. In its current implementation it will probably not work on CC....
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2971 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-03-05 09:23:57 +00:00
peabody124
ec29920a8d OP-315: Clean up RTC calls into a separate function. Unfortunately still need
to add function headers into portmacro.h

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2942 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-03-03 04:28:38 +00:00
stac
bbb3882826 bl_openpilot: bind to new COM, USART and SPI drivers
- Removed all unnecessary device instances and their cfg's.
  - SPI to SD card
  - I2C
  - Aux USART
- Moved SPI baudrate setting into cfg rather than init func.
- Abstracted forcing slave select under OPAHRS API.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2786 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-14 01:17:32 +00:00
sambas
f3bce1705b OP-22 Flight/PiOS: Spektrum fix, OP tested on ground not flown yet, CC not tested.
pios_rcinput.[ch] outdated

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2775 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-13 13:10:02 +00:00
stac
66a9d53d0a hwinit: Convert I2C driver to dynamic init
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2773 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-12 22:19:54 +00:00
stac
3fda65c5d3 hwinit: Convert SPI drivers to dynamic init
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2772 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-12 22:19:50 +00:00
stac
841b0d3d6d hwinit: Convert COM and USART to dynamic init
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2771 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-12 22:19:43 +00:00
peabody124
fedadb1275 CC-8: Move the queue registration into the ADC PIOS driver to allow other
functions to use it easily

Conflicts:

	flight/Modules/Attitude/attitude.c

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2707 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-03 02:42:43 +00:00
peabody124
97acaa2402 CC-15 Gets settings saved to flash chip on CC using crude sector based storage.
Sector based on Object ID so could overlap :-(.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2662 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-01 02:18:12 +00:00
peabody124
e27c9c0b7a CC-6 Rename Flash function to not be all upper case consistent with other PIOS
functions

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2660 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-01 02:18:04 +00:00
peabody124
c9207b3754 CC-14 PIOS/Servo: Set more than two bank speeds
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2658 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-01 02:17:55 +00:00
stac
083e2b01a9 uavobject: Use linker to produce uavobj initcalls
The UAVObject initcall list is now automatically
generated at link time based on the exact set of
UAVObjects linked into the firmware image.

This will allow any subset of UAVObjects to be
used in any firmware image.

The uavobj_initcall() macro automatically adds the
marked function's address into the .initcalluavobj.init
ELF section.

The UAVObjectsInitializeAll() function now simply
iterates over the functions listed in the
.initcalluavobj.init section and calls them.

You can see the contents of this section in the ELF file
like this:
  ./tools/arm-2009q3/bin/arm-none-eabi-objdump \
      --syms -j .initcalluavobj.init \
      ./build/openpilot/OpenPilot.elf

This is fundamentally the same mechanism that the Linux
kernel uses to initialize the specific set of components
that the user has selected in their kernel configuration.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2630 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-30 22:46:48 +00:00
pip
5daf6fd1c0 Added PIP_DUMP_RAW option in ahrs.c and brought back public acces to function PIOS_ADC_GetOverSampling(void).
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2623 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-29 15:59:35 +00:00
sambas
ba5ebb6b13 OP-303 PIOS/Sonar: preliminary support for HCSR04 ultrasound altimeter module, tested and working :)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2610 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-28 19:21:22 +00:00
sambas
195b63b6bb OP-22 PIOS/Spektrum: Made spektrum input driver, NOT YET TESTED!!!, also preliminary support for CC, sync/supv timer not yet fixed.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2602 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-28 09:25:30 +00:00
peabody124
c759253b77 CC-6 Flash chip working to read ID. Also tweaked how the semaphore for the SPI
bus is used to be a bit safer.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2591 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-25 17:46:27 +00:00
peabody124
00a3e82c70 CC-6 PIOS/SPI: Add semaphore to SPI device structure that can be used to ensure
only one CS line is asserted.  No checks are enforced on this by the SPI code
as I cant see a clean way of it being aware of the CS lines.  We could add
another CS mode those which is driver managed per transfer and has a GPIO i
line for each device.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2579 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-24 07:52:17 +00:00
peabody124
d2f3e0d379 CC-6 Initial code for the flash chip on CC
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2578 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-24 07:52:14 +00:00
peabody124
d4b4a6ca37 CC-3 Modules/CCAttitude: Add oversamplign to the accel data
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2576 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-24 07:52:08 +00:00
peabody124
99fcd089d4 OP-291 PIOS/Servo: Make the remapping of timers a part of the driver structure
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2569 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-24 07:51:48 +00:00
peabody124
da96ce15b9 OP-256 PIOS/PWM: Converting PWM input to use standard driver structure.
Beginning of unifying the input types into PIOS_RECEIVER.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2568 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-24 07:51:45 +00:00
peabody124
99f2f3c68b OP-291 CC Servo configuration: Gets S5 and S6 working
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2566 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-24 07:51:38 +00:00
peabody124
65e02eeb25 OP-293 PIOS/ADC: Fixed issue with DMA engine and odd numbers of channels not
accounting for the fact they are transferred in pairs when using ADC2

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2510 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-21 17:18:20 +00:00
peabody124
2d9f7f32d1 OP-291 PiOS/Servo: Converting output to use driver system
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2499 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-21 03:40:21 +00:00
peabody124
cf17569de7 CC-1 Modules/CCAtttitude: Calling the ADXL345 library and getting the accel and
gyro data into attitude raw.  Hardcoded calibration for now.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2474 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-17 08:45:40 +00:00
peabody124
21b4e55029 OP-14 OP-16: I2C Improvements
1) Added nack counter monitoring
2) Made timeout for getting semaphore in I2C user space code use the one from
driver and record timeouts.  This does not influence timeouts in the non
FreeRTOS case
3) Remove case block from the error handler so that all bus errors reset the
i2c interface

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2469 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-17 02:11:12 +00:00
peabody124
0259b6d1f1 OP-269 PIOS/ADC: First part of conversion to driver structures
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2444 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-16 02:45:39 +00:00
peabody124
81b0c3fdb6 OP-269 PiOS/ADC: Moved AHRS ADC code to PiOS and made all the projects use it
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2440 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-16 02:45:22 +00:00
peabody124
c59a1ff018 OP-265 OP-266: FreeRTOS configuration per project because of available heap
size (may eventually need to be per revision if we get bigger ram).  Typo in a
the ifdefs to get allow disabling SDCARD

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2423 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-14 01:38:42 +00:00
peabody124
f0c36b13a4 PiOS/USART: Use the buffer size defined in the board file
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2421 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-14 01:38:37 +00:00
peabody124
940792db5c OP-265 CopterControl: Fork main OpenPilot directory
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2416 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-14 01:38:24 +00:00
peabody124
07798bb2db PIOS/WDG: Add back the returned delay for code that wants to clear WDG more
rarely

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2403 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-13 19:01:33 +00:00
zedamota
1f89ee1865 OP-21/Bootloader - Change HW ID to 16bits. Should still be compatible with the old version.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2398 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-13 14:36:32 +00:00
peabody124
bbbd9a10e3 OP-14 I2C Diagnostics: Improve the logging so that the events going into FSM
are logged, and separately the erirq and evirq logs are exported

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2368 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-10 05:42:53 +00:00
peabody124
b173d74821 OP-237 I2C ESC support. This _will_ require you to reconfigure your
ActuatorSettings although for PWM aircrafts it should be done exactly as before

Actuator: Store the update times and maximum update time

OP-14 I2C: Start tracking short history of events and states in driver for
logging
OP-237 Flight/Actuator: Support for I2C based ESCs

OP-237 MK_ESC: Send all four motors as one atomic transfer

OP-237 Flight/Actuator: Allow channels to be mapped to MK I2C interface.  Currently
mixer channels are either PWM or MK but in the future this will change to
support more than 8 channels.

OP-16 PiOS/I2C: Further work to try and make I2C more stable, mstly special case
handline in IRQ

OP-237 I2C ESC: Support for Astect 4 channel ESCs

OP-237: When the I2C Actuator write update fails track this

OP-237 Actuator Settings: Change the way motor types are selected to keep that
information more appropriately within ActuatorSettings instead of MixerSettings

Also make motors stay at or above neutral when armed and throttle > 0

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2366 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-10 01:11:44 +00:00
peabody124
ed11e64bb2 OP-251 Watchdog: Get rid of the old extra watchdog module and instead have
tasks directly update a flag for each module (which they register) and when all
flags set clear the watchdog then.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2365 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-10 00:16:30 +00:00
vassilis
1e78cc7a30 Flight/FlightPlan: First release of flight plan scripting. The scripting engine is based on the PyMite Python VM. The released code is able to execute a simple python script on the target. However it is currently disabled from the makefile due to a few issues with more complex scripts. When the library is enabled in the makefile a python interpreter will be needed to compile the firmware since some intermediate code is generated by PyMite.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2364 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-09 22:36:15 +00:00
vassilis
407e660c97 Flight/TaskMonitor: Create TaskMonitor library, used to monitor the remaining task size of all running tasks.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2349 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-08 23:43:34 +00:00
zedamota
14ef24a3de OP-21/Bootloader - Maximize flash space available for user code. Bring back delay on HID send (board->pc) it still hangs when blasted with data. AHRS is now Readable.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2263 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-12-21 17:25:24 +00:00
peabody124
af99c31a61 PiOS/I2C: Fixed typo and also the values for I2C Diagnostics when disabled.
Enabled by default though.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2243 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-12-18 07:09:28 +00:00
peabody124
4b4a66c2d7 PiOS/I2C: Lots of small changes. Added a few weird bus events that are
sometimes thrown, and made errors not lock it up by default.  It works for me,
but since this has historically been associated with lots of lock ups please
check your systems carefully.

PiOS/I2C: Make the bus by default try to recover from errors instead of locking
up

PiOS/I2C: After a bus error and clocking all previous data create a STOP
condition to make sure bus is released (note, this also requires creating a
START condition first)

PiOS/I2C: If the same event hits the I2C bus twice in a row then disregard
second one, there is no situation where we should get the same event multiple
times that matters and this gets us out really quickly to catch the real
events.  I was seeing this with repeated 0x70084 which means byte transmitted.
This is related to STM32 bugs in the IRQ timings I believe.

PiOS/I2C: 1) Mask out some bits we don't care about in the event flags
2) Don't lock up if the give semaphore fails, although why it does is strange
3) Recover from bus failure through the "auto" state path instead of just
coding state

PiOS/I2C: Change the reset bus code to follow
http://www.analog.com/static/imported-files/application_notes/54305147357414AN686_0.pdf
(thanks for the reference Neontangerine).  Although this may actually NOT clear
the bus the first time through, subsequent bus errors should eventually clock
it out.  The up side is it is less likely to clock a bunch of 1s into an ESC
and make it run up.

PiOS/I2C: Some cleaned up code for getting a snippet of the history when
something strange happens

PiOS/I2C: Export logging information from I2C through a UAV object

PiOS/I2C: Improve the diagnostic information

PiOS/I2C: Need to handle the event 0x30084.  This seems to happen between a
byte transmitted and new byte started

PiOS/I2C: Handle the NACK condition by simply going to the stopping state.

PiOS/I2C: Add a new NACK state to handle sending the STOP signal after a NACK
following the STM documentation.  Other error conditions still are not dealt
with.

PiOS/I2C: Should handle the NACK condition from all the write cases.  Need to
think about read cases

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2239 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-12-17 07:01:58 +00:00
pip
0cae6df8b0 Aligned fifo buffers to 32-bit for possible speed improvement.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2173 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-11-28 11:06:45 +00:00
pip
d4c24de556 Updated to use the new fifo_init function
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2172 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-11-28 11:00:20 +00:00
peabody124
e3dd542609 OP-203 PIOS_USART: Make USART Rx code use fifo_buffer
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2141 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-11-23 17:13:44 +00:00
sambas
f94dc41712 OP-73 Flight/PiOS: runtime RC input change, initial files just for review, not integrated to build yet
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2106 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-11-11 19:09:39 +00:00
kokomojoe
20c6e2292a OP-185 Flight helper functions for the firmware IAP object. Allows setting/clearing of back-up registers
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1890 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-10-06 02:02:37 +00:00
les
498f3d0fa6 PIOS SPI: Added a function to detect if the channel is busy
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1829 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-10-01 16:52:20 +00:00
peabody124
3c021c09d9 Flight/PiOS: Whitespace changes
find ./flight/PiOS/inc/ \! \( -name '*~' -a -prune \) -type f    | xargs -I{}
bash -c 'echo {}; dos2unix {}; gnuindent -npro -kr -i8 -ts8 -sob -ss -ncs -cp1
-il0 -hnl -l150 {};'

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1777 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-27 07:28:45 +00:00
peabody124
77b68e5169 Flight/Guidance: Initial template for guidance module
Flight: Create PositionDesired (the active waypoint) UAVObject and make the FlightSituationActual no update since it not used.
Flight: New velocity desired object that passes information between the look computing the desired velocity and the PID loop to get it (updated at different rates)
UAVObjects/PositionActual: Remove unused GPS fields
UAVObjects/PositionActual VelocityActual: Split the velocity into a separate object.  ALso make sure all the information telemetered around is in cm to avoid using floats.
UAVObject/GuidanceSettings: New guidance settings object for the guidance module
Flight/Posix: Add the new objects to the Posix sim
Flight/Guidance: Computes a desired velocity based on position error than runs a PID loop to control roll and pitch to achieve that velocity.  All distances are in cm, and updated the PositionActual fields to reflect this and use int32.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1760 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-26 03:06:27 +00:00
peabody124
a01783b2a8 OP-140 AHRS: Explicilty deal with if it is initialized or not, use that to
determine retransmitting calibration, home location and such.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1755 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-25 21:05:38 +00:00
peabody124
9b28f2d72c OP-167 OP-157 AHRS/Calibration: Added mag scale and really cleaned up calibration.
Calibration should take less time now too (using second moments to estimate
variance in one pass).  Now need to change to multiple messages to get the
calibration in to keep the request message size minimal.  Also currently
running sensor calibrate doesn't store the gyro bias so if you want to use this
you'll have to tweak it manually.  I'll fix that step tomorrow.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1741 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-25 09:20:38 +00:00
zedamota
c9752a6a3a OP-21/Flight Bootloader - some changes for the bootloader to work
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1682 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-18 23:11:42 +00:00
peabody124
885c966e53 AHRS: Added a tracker for number of ADC updates the EKF misses. Also updated the Telemetry autogenerated files to accomodate the 11500 baud rate.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1652 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-16 02:59:00 +00:00
peabody124
19e80da928 AHRS: Update UAVObject with information about AHRS rate
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1650 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-16 01:54:21 +00:00
zedamota
c72a5b1cfe OP-21/Flight Bootloader
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1642 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-15 17:08:24 +00:00
stac
55d90970ed hmc5843: hide internal #defines and functions
Way too much was being exposed in the API for the
HMC5843.  This commit properly hides internal
details of the driver.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1629 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-15 14:21:04 +00:00
stac
0e7a801e9e hmc5843: Add support for DRDY signal from magnetometer
The DRDY signal from the magnetometer is connected to PB8
on the STM32.  This pin is now configured as an external
interrupt and is now used to signal when new data is
available from the magnetometer.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1628 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-15 14:21:02 +00:00
stac
4ac001553d hmc5843: convert line endings from CRLF to LF
No functional changes.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1627 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-15 14:21:00 +00:00
stac
88e73906d0 i2c: Add recovery code for i2c bus errors
I2C bus errors are now recoverable.  The bus is properly reset
and an error indication is now provided to the caller whenever
a bus error occurs during processing of the transaction list.

For now, the users of the I2C layer just retry infinitely on
failure.  The BMP085 and HMC5843 code should be changed to
report errors to its callers to allow a more sensible retry
strategy.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1625 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-15 14:20:57 +00:00
stac
65ad2caf8a i2c: Make transaction initiator available in txn list
The info field in the pios_i2c_txn list can now be used
to provide a const string which describes the context
for this transaction.

This is very helpful when diagnosing an error that occurs
somewhere in the middle of the I2C FSM since the FSM runs
primarily in the ISR where the original context for the
transactions is no longer available in the traceback.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1622 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-15 14:20:53 +00:00
stac
85c60479c1 i2c: rename FSM faulted state
Differentiate the _FSM_ faulted from the (soon to
exist _BUS_ faulted state.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1621 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-15 14:20:52 +00:00
pip
cc3860daaf Added 'uint32_t PIOS_SYS_getCPUFlashSize(void)' into pios_sys.c/h files.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1616 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-14 09:18:55 +00:00
pip
8bfaa997d3 made curr_state 'volatile' in pios_i2c_priv.h to prevernt compiler optimization lockup.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1611 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-13 20:52:56 +00:00
stac
d18e0c3ef8 ahrscomms: Add low-level message code for bootloader msgs
Implement low-level utility functions for sending/receiving
the opahrs proto v0 (bootloader) messages.  These are used
by the OP firmware loader and the AHRS bootloader.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1586 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-11 23:06:31 +00:00
stac
6bf3038f3f ahrscomms: provide helper function for simple requests
This cleans up some of the boiler plate code that is
repeasted for simple (empty) requests that expect a
response.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1584 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-11 23:06:28 +00:00
stac
7ecbb5f5b8 opahrs_proto: Add new boot and versions messages
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1583 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-11 23:06:26 +00:00
stac
d1dc300081 ahrscomms: remove unused sync and switch_proto messages
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1582 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-11 23:06:25 +00:00
peabody124
b853c392f3 Flight: Was only returning half of the serial number (thanks for catching that Pip)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1476 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-31 02:33:47 +00:00
pip
ba5f1b37ee changed pios watchdog from 8-bit to 16-bit ms capability, plus moved the .h file from the .c folder into the inc folder
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1466 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-30 16:29:36 +00:00
peabody124
f202884ce8 AHRS: Numerous changes. Added CPU load monitoring for AHRS as well as some friendly debugging output options. Also added a new CalibrationMode setting to AHRS (Echo) to speed up sensor calibration. Cleaned up the 6 point calibration interface to make it more friendly, but I think Edouard will clobber it with something nice and sexy :).
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1455 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-29 06:38:30 +00:00
stac
47df1faa8d ahrs: whitespace adjustments
No functional changes.  Whitespace/tab fixups only.
Use TRUE/FALSE instead of 1/0.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1430 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-27 02:14:58 +00:00
peabody124
4ca10e92c7 OP-121 OP-122 Flight: Improved USB HID communication.
1. Added reenumeration function and call it on USB init (device will appear after reprogramming now)
  2. Moved buffer.c to general flight/Libraries location
  3. Removed the 62 byte transmission limitation by adding a transmission buffer
  4. Sped up USB communication by increasing endpoint polling frequency

Note, that the nonblocking and blocking USB send functions are not blocking entirely correcting.  The blocking calls the nonblocking, and the nonblocking blocks until the last chunk has started tranmission if it's a big transmission.  The buffering I added would generalize to non-blocking nicely, but would require using the EP1(IN) callback to handle most of the tranmission.  This creates a lot of issues if one function is pushing data onto the buffer and the interrupt is sending.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1403 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-25 05:32:52 +00:00
peabody124
bd8fffe4d0 AHRS/Flight: Renamed AttitudeSettings to AhrsSettings to make it more intuitive. Added the ability to change the algorithm from GCS.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1383 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-23 03:39:13 +00:00
peabody124
2596f43511 OP-120 AHRS: Moved conversion of quaternion to RPY over from AHRS to OP to minimize transfer and computational load on AHRS.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1381 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-23 02:35:39 +00:00
peabody124
5662d85c4e OP-120 AHRS: Tightened up the communication protocol so it runs more quickly. Looks ok in gdb but GCS not crashing right now (rendering error) so I can't test it properly.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1366 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-22 00:21:54 +00:00
peabody124
8897c441fa OP-118 AHRS: Added AHRSCalibration object and messages associated with that to AHRS. Also made AHRS run calibration only when requested. We will create a GCS plugin that runs through computing the calibration settings. To compute the variances on the AHRS set the measure variances to true, wait ten seconds, then set it to false to read it back.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1363 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-21 21:46:02 +00:00
stac
7b2111e512 baroaltitude: rename AltitudeActual to BaroAltitude
This is to align the object names to matches the UAVObject
architecture doc.  No functional changes.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1351 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-21 16:19:10 +00:00
stac
98822bff98 i2c: force bus free on warm starts
Since the i2c bus is bidirectional, there are certain
states (eg. part way through a read) where the slave
device is in control of driving the SDA line.

On a cold start (power on), the slave devices are all
quiescent and will not drive the bus.  However, on a warm
start (eg. watchdog or jtag restart), it is possible that as
the CPU boots, the slave device may be holding the SDA line
low.  This is a bus busy condition and will prevent the I2C
bus master in the CPU from being able to seize the bus during
init.

The fix for this is to clock the i2c bus sufficiently to ensure
that the the slave device finishes its transaction and releases
the bus.

Once the slave has released the bus, the bus master can properly
initialize and assert a STOP condition on the bus.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1349 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-21 16:19:02 +00:00
peabody124
ef0b307353 [OP-119] Flight/AHRS: Created a HomeLocation object which is updated when the GPS gets an initial 3D fix and populated with the information to convert from LLA from the GPS to NED reference frame. Also added a message for passing the MagneticNorth vector to the AHRS and removed that computation from AHRS.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1337 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-19 20:38:27 +00:00
peabody124
3c4def13cc AHRS: Added message to pass GPS information into AHRS from OP. This is then converted
into NED reference frame and used in the INSGPS algorithm, although currently this
information isn't propagated back to OP.  Data structures related to the GPS position
into the algorithm and the position estimate out will likely be in flux.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1334 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-19 05:18:34 +00:00
peabody124
cfd20922cd AHRS: Added the filtered data to the attitude raw object. Even though this seems like an oxymoron it's still raw to the EKF algorithm, and nice to see the real values after filtering to make sure nothing weird is going on. However, if people don't like this I'm open to suggestions/patches. I'd maybe suggest the whole attituderaw object be converted to ahrsraw anyway since it's more like that (eg. none of the values are actually attitude estimates).
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1325 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-18 14:54:24 +00:00
peabody124
450cf07a89 AHRS: Keeping magnetometer I2C address consistent with change to I2C driver.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1323 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-18 13:54:15 +00:00
FredericG
b46bc68e96 "addr" field of I2C transaction struct now takes real I2C address, and not address that is pre-shifted to accommodate the R/W bit
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1321 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-18 10:04:55 +00:00
stac
3125ecfc4e AHRSComms: altitude sensor data is now sent to AHRS
Altitude/pressure sensor data is sent to the AHRS whenever
the AltitudeActual object is updated.

Altitude, Pressure and Temperature are sent as floats.
Same as in the UAVObject that goes to the GCS.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1291 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-15 01:02:13 +00:00
stac
c3e509c2cb attituderaw: Replace HeadingActual with AttitudeRaw
AttitudeRaw now includes:
 - magnetometers XYZ (in mG)
 - gyros XYZ (raw ADC samples)
 - accelerometers XYZ (raw ADC samples)
 - placeholder for gyro temp sensors (read as zero for now)

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1289 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-14 23:42:14 +00:00
stac
f74c6ffdd5 i2c: rewrite i2c layer
The STM32 I2C block has a number of errata associated with it.
These errata are primarily related to timing sensitivities between
the peripheral and the interrupt handler.  In particular, the
correct generation of the stop bit relies on the I2C IRQ running
immediately and not being held off for any reason.

NOTE: The I2C interrupts must be the highest priority IRQs in the
      system to ensure correct operation.

I2C protocol is now implemented as a formal state machine.
See: stm32_i2c_fsm.{dot,jpg} for FSM description.

I2C init is now expressed by const initializers in pios_board.c
for both OP and AHRS boards.

I2C device drivers (ie. bmp085/hmc5843) now pass in const arrays
of an unlimited number of bus transfers to be done atomically.
The I2C adapter driver now handles all bus-level locking across the
list of transactions.  Generation of start/restart/stop conditions
are handled automatically over the list of transactions.

Timeouts have been removed from the API for now.  May be added
back later.

This driver has run error free on both the OP and AHRS boards for
up to 48hrs but it still sometimes fails earlier than that on the OP
board.  There is another possible set of improvements to the driver
that could employ the DMA engine for transfers of >= 2bytes.  This
change would reduce the timing sensitivities between the peripheral
and the driver but unfortunately, both the SPI and I2C interfaces
share the DMA1 engine.  That means only one of these two peripherals
can use the DMA engine and right now, SPI between OP and AHRS is
already using it.

Failures are currently fatal and will lock up the CPU.  This allows
useful information to be obtained in the failure cases.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1241 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-08 04:15:08 +00:00
peabody124
0fdfbb2ffb Deleting old USB code that I meant to delete a while ago. Also changed names of some functions to OP. Finally fixed the USB taking over PIOS telemetry. Detects the USB cable and that the configuration has been taken by the USB bus.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1217 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-05 23:43:52 +00:00
pip
0331f05e9a Added extra LED's .. now up to 4 LED's .. (PipBee has 4 controllable LED's)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1207 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-04 17:32:42 +00:00
sambas
7f6336d324 OP-22 Flight/PiOS: Spektrum reworked, input is mapped to old aux in receiver connector, works nicely with calibration plugin. Also bind works, just needs config flag to bind on powerup
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1189 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-01 10:34:07 +00:00
peabody124
7e6afe5a75 Updated HID code to do packet processing in OS indepdent layer. Should now work on all platforms. Please test and get back to me. Maximum object size of 62 bytes currently.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1174 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-28 18:55:04 +00:00
peabody124
27d429fe18 Got better HID report design with valid data length embedded in report
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1164 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-27 17:41:56 +00:00
peabody124
fe616df48d Further tweaks. Will start trying to get reliable communication with larger report size tomorrow
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1159 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-27 07:56:50 +00:00
peabody124
840f7ff456 A version of the firmware that successfully Acks back and forth over HID. Still need to refine the PIOS interface and make GCS strip out the report ID data (if necessary). Also note: currently if you run too many modules the watchdog timer kicks in. I haven't determined if this is due to an interrupt binding up or what (and why it doesn't happen more often since I can't find any code that explicitly resets the WWDG).
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1157 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-27 06:22:34 +00:00
peabody124
d89cd43cd1 Further tweaks to the HID update
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1156 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-27 05:28:04 +00:00
peabody124
c46dcea73a Pretty major update of the USB HID core. Removed a lot of old code related to custom drivers and BSL (which will be brought back under HID). Device enumerates but still not communicating. Hopefully nothing broken, lots changed.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1155 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-27 03:19:07 +00:00
peabody124
d928676f5e More documentation updates, standardizing format to include addtogroup at the beginning of headers so files are associated with modules
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1121 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-16 19:53:35 +00:00
peabody124
99e94228a9 More doxygen updates
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1106 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-16 05:31:11 +00:00
stac
17bea4cb91 ahrscomms: connect the OP board to the AHRS board
The AHRS comms module now sync's with the AHRS and
exchanges interesting data periodically.  Whenever
the link to the AHRS is down, the AHRSComms alarm is
raised.

This is fairly basic for now but provides the last
piece of the infrastructure to move data back/forth
between the OP and the AHRS.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1014 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-04 02:21:49 +00:00
stac
29a8f05ac9 mag sensor: put some bounds on the parameters
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1012 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-04 02:21:45 +00:00
stac
a3a2dbd634 spi: Add support for hardware CRC generation/checking
PIOS SPI devices may now make use of automatic CRC generation
and checking on block transfers.  Only supports CRC8 for now.

Since the SPI interface CRC calculation continues across message
boundaries (ie. not reset on every transfer), we must manually reset
the CRC registers for every transfer to allow the two sides of the
link to resynchronize.

Unfortunately, resetting the CRC registers requires disabling the
SPI peripheral which must now be done on every block transfer.

Note: The last byte of the tx buffer is never sent and is assumed to
      be a place holder for the tx CRC8.
Note: The last byte of the rx buffer is expected to hold the rx CRC8.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1011 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-04 02:21:42 +00:00
stac
c12b7e3fed spi: tx buffer is now const
Tx buffers should not be modified.  This allows passing const data
to the transfer function.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1010 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-04 02:21:40 +00:00
stac
89a6d6d912 ahrs spi: Add definition of OP<->AHRS SPI protocol
This defines the SPI message format as well as a few
initial messages for moving data across the link.

The v0 messages are place holders for firmware download
in the bootloader.

The v1 messages are to be used by the main application.

Note: This is not the final protocol definition.
      Subject to change without notice.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1004 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-04 02:21:15 +00:00
stac
71e491e3c1 com: mark tx buffer as const throughout API
The com layer transmit functions should provide guarantees
that they will not modify the buffer that you're transmitting.
Declaring the parameter as a pointer to const keeps the underlying
implementations honest.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1001 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-04 02:21:08 +00:00
FredericG
5d9a718430 Made pios_com_num_devices const
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@837 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-06-20 17:59:48 +00:00
stac
771a56ca9d com/usart: generalize com driver API
- Created a pluggable COM layer
- Converted COM + USART init into static initializers
  rather than typedefs
- Generalized the USB HID COM API to match the USART
  API.
- Changed USART and COM layers to be data driven rather
  than #ifdef'ing/switching on the specifics of each port

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@760 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-06-13 04:24:26 +00:00
stac
8d015a57d0 pios spi: support both master and slave configs
Added support for SPI slave configurations to the pios SPI layer.

Converted the board specific configuration for the PIOS SPI layer to
use const static initializers rather than #defines (see pios_board.c).

SPI interface between the OP board and the AHRS is now operational at
a basic level, capable of moving simple single byte messages between
boards.  Multi-byte, CRC protected messages will be added on top of this.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@759 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-06-13 04:23:44 +00:00
fredericg
a2beb49257 Changed PIOS_DEBUG_Panic()
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@694 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-31 16:22:58 +00:00
stac
69de42db49 Add AHRS attitude module and driver skeletons
- New Attitude module for AHRS (skeleton)
 - New AttitudeSettings UAVobject
 - New AttitudeActual UAVobject
 - Regenerated UAVobjects
 - Added new UAVobjects to OpenPilot and GCS builds
 - New PiOS driver for OpenPilot AHRS (stubs only)

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@655 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-24 16:33:36 +00:00
sambas
d7b3a158d6 OP-22 Flight/PiOS: Spektrum bind function tested and working.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@649 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-23 11:19:28 +00:00
stac
d02a3325d9 altitude: Add altitude module which reads BMP085
This module reads from the BMP085 pressure sensor.  It periodically
updates the pressure (kPa) and temperature (C) as well as the
calculated altitude (m).

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@640 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-19 04:55:56 +00:00
stac
514d46f5b6 freertos: fix RTOS API calls from interrupt level
FreeRTOS has a strict requirement that even interrupt-safe API calls (ie.
those ending in "FromISR") can only be called from ISRs that are at lesser
or equal priorities to configMAX_SYSCALL_INTERRUPT_PRIORITY.  See the
"configKERNEL_INTERRUPT_PRIORITY and configMAX_SYSCALL_INTERRUPT_PRIORITY"
section at:
  http://www.freertos.org/a00110.html

The interrupt numbers used on the Cortex-M3 CPU has a somewhat backward
representation of the interrupt numbers so 255 = lowest priority and
0 = highest priority.

The calculation is further complicated by the STM32 implementation only using
the upper 4 bits of the priority value.  Only 0x00, 0x10, 0x20, ..., 0xE0, 0xF0
represent useful interrupt priorities.

FreeRTOS requires that MAX_SYSCALL and KERNEL interrupt priorities are expressed
as raw unshifted 8-bit values to be programmed directly into the BASEPRI register.

The priority values passed to the NVIC initialization, however, are expected
to be 4-bit values and are shifted up by 4 within NVIC_Init() for you.

The end result is that we need this arrangement:

[highest priority]
   NVIC_0 (Non-maskable-interrupt)
   NVIC_1
   NVIC_2
[Must NOT call FreeRTOS APIs above here]
   configMAX_SYSCALL_INTERRUPT_PRIORITY (now at 48 = 0x30 = NVIC_3)
   PIOS_IRQ_PRIO_HIGHEST (cur. NVIC_4)
   PIOS_IRQ_PRIO_HIGH    (cur. NVIC_5)
   PIOS_IRQ_PRIO_MID     (cur. NVIC_8)
   PIOS_IRQ_PRIO_LOW     (cur. NVIC_12)
   configKERNEL_INTERRUPT_PRIORITY (240 = 0xF0 = NVIC_15)
[lowest priority]

The previous config had configMAX_SYSCALL_INTERRUPT_PRIORITY set at
191 (0xBF) which is effectively NVIC_11.  This was allowing all of
the MID, HIGH and HIGHEST interrupt handlers to preempt the OS in
its critical sections.  Since some of these ISRs were calling
FreeRTOS APIs, this would result in corrupting internal data structures
within the OS.

It should be ok to move the configKERNEL_INTERRUPT_PRIORITY to a higher
priority as long as it is less than configMAX_SYSCALL_INTERRUPT_PRIORITY.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@637 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-18 04:50:38 +00:00
sambas
66fa56a1da OP-22 Flight/PiOS: Spektrum simple decoder works, getting seven working channels with my DX7 tx
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@630 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-16 10:04:07 +00:00
sambas
76cd72915d OP-22 Flight/PiOS: first tests done with spektrum satellite, I can read binded receiver serial stream
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@629 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-16 08:35:38 +00:00
sambas
26aecf720d OP-22 Flight/PiOS: Spektrum satellite protocol started
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@626 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-15 18:22:03 +00:00
gussy
73b5e29e02 Finalised and verified PIOS_HMC5843 library.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@624 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-15 12:50:05 +00:00
gussy
ff73ab5a80 More updates to cross-target compatibility.
Added PIOS_I2C into AHRS code.
Added PIOS_HMC5843 Module.




git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@617 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-12 08:18:49 +00:00
vassilis
a31215293d Flight\Telemetry Implement telemetry settings object, added functions for changing the baud rate in PiOS
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@607 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-08 02:44:26 +00:00
gussy
0aba12fe1f Loopback test of HID working. Still a WIP but committing what I have to show progress.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@582 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-04 18:54:43 +00:00
fredericg
3281b1a128 OP-27 Use RTOS in LockDevice() and UnlockDevice()
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@564 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-05-01 14:49:51 +00:00
vassilis
8c11a03129 Flight/Alarms Implemented Alarms library, now checking for stack overflow, out of memory, event and other errors (see the SystemAlarms object). All modules will be reporting their alarms using this library.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@554 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-04-27 01:55:28 +00:00
vassilis
4f0377194d Flight/PiOS Remove use of semaphores in COM/USB ISR (not used and not working also causing random crashes)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@540 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-04-25 02:17:25 +00:00
vassilis
40beb15129 OP-4 Flight/System Created CPU utilization measurement and created object to report system information (load, heap and time)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@519 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-04-18 02:13:59 +00:00
vassilis
89a6dd30d1 OP-4 Flight/Telemetry Create new objects to report statistics of the telemetry link (plus a few bug fixes, heap size was also increased)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@515 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-04-17 22:16:20 +00:00
vassilis
f4c4b1371a Flight/Settings: Remove old settings implementation (replaced with binary settings as UAVObjects)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@465 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-04-10 01:35:13 +00:00