rooty/LibrePilot
1
0
Fork 0
mirror of https://bitbucket.org/librepilot/librepilot.git synced 2024-11-30 08:24:11 +01:00
Code Issues Releases Activity
4,998 Commits 5 Branches 8 Tags 266 MiB
8059004755
Commit Graph

2418 Commits

Author SHA1 Message Date
James Cotton
900780e10c Add bias estimation to the altitude fusion algorithm. Necessary to increase 
the gains on acceleration and velocity feedback terms (they are a problem when
biased).
 2012-02-19 11:38:09 -06:00
James Cotton
47fac7e31c Move the throttle setting code for alt hold into the fast accel loop. 2012-02-18 18:16:15 -06:00
James Cotton
7d4582e5f0 Update the altitude KF to use the updated measurements appropriately and check 
in the relevant matlab code to check it and genererate it.  Produces quite
smooth traces.
 2012-02-16 05:33:47 -06:00
James Cotton
c957172f8f In the case of swapping in userspace due to the buffer being blocked during 
ISR, make sure the latency is less than 50 us to avoid framesync errors.  Still
seeing a few nonsense packets on Overo side but fairly few.  Probably need to
add CRC to whole packet now and call it done.
 2012-02-14 11:06:16 -06:00
James Cotton
1930d092eb In the case where the overo scheduler cannot swap buffers (userspace loading 
it) then set a flag so as soon as the buffer is loaded then we schedule it.
 2012-02-14 11:00:29 -06:00
James Cotton
f04c58b0f4 Make the overo transaction occur based on the rising edge of the NSS line. 
This fixes most of the frame sync problems.  However, it's a bit hacky as
there is currently hardware information inside a module.
 2012-02-14 10:37:30 -06:00
James Cotton
d018d93e88 Clean up previous commit a bit and make the sampling rate a variable (and adapt 
the sampling time accordingly).
 2012-02-13 01:49:54 -06:00
James Cotton
3acbfbe96c Convert the pressure sensor code to most of the calculations as int64 to retain 
precision.
 2012-02-13 01:22:48 -06:00
James Cotton
4717af1afd Swap telemetry port and gps ports back 2012-02-12 13:55:52 -06:00
James Cotton
f23f53dc4e Add settings for the altitude kalman filter settings and init the state when 
first measurement arrives
 2012-02-12 09:07:27 -06:00
James Cotton
34ca5777dd Kalman filter for altitude 2012-02-11 21:08:19 -06:00
James Cotton
d8f0494e57 Merge branch 'revolution' into revolution_overo 2012-02-11 20:02:20 -06:00
Alessio Morale
22b211167c Ported pios_iap.c to F4 
restored failed boot count check on pios_board.c for revo
 2012-02-11 13:49:32 +01:00
James Cotton
3026527801 Now the desired altitude is relative to when the switch was flipped so that the 
baro altitude module can use a smoothed altitude estimate for the starting
point.
 2012-02-08 23:02:29 -06:00
James Cotton
80d602ef7b Switch order of some commands to make sure it loads the correct hover throttle 2012-02-08 20:47:10 -06:00
James Cotton
ab41bae071 Separately smooth the error estimate from the derivative 2012-02-08 11:15:33 -06:00
James Cotton
60c951843d Use backtracking to limit integral in altitude hold and smooth the velocity 
error.  Initialize the throttle integral better.
 2012-02-08 10:39:31 -06:00
James Cotton
c6b1d6b8df Rework the altitude hold code a bit 2012-02-08 09:42:10 -06:00
James Cotton
49a03a868b Merge branch 'altitudehold' into revolution_overo 
Conflicts:
	flight/OpenPilot/UAVObjects.inc
	flight/Project/OpenPilotOSX/OpenPilotOSX.xcodeproj/project.pbxproj
	flight/Revolution/Makefile
	flight/Revolution/ins.c
 2012-02-07 23:00:29 -06:00
James Cotton
6ec0f06c80 Back to 1024 byte packets 2012-02-07 13:02:11 -06:00
James Cotton
2c60447200 Switch back to 512 byte packets and fix bug when writing the header size that 
was smashing the crc
 2012-02-07 11:32:04 -06:00
James Cotton
221a0c5e53 Add the number of dropped updates to the overosync stats 2012-02-07 09:13:26 -06:00
James Cotton
a89d425b23 Reset the received rate for overo sync object 2012-02-07 09:01:58 -06:00
James Cotton
02bec750bd In the attitude loop need to check all the queues even if unused or the event 
system will have warnings
 2012-02-07 08:46:34 -06:00
Stacey Sheldon
e2939dae2a revo usb: Add support for USB to Revo 2012-02-07 02:25:31 -05:00
Stacey Sheldon
8b73ae7d16 remove trailing whitespace 2012-02-07 02:25:31 -05:00
Stacey Sheldon
b8c16fe7a5 hw defs: move misc defines and non-const data out of board_hw_defs.c 
The board_hw_defs.c file should only contain static
const declarations that only describe the hardware.

All other non-const variables should be put into one
of the pios_board.c files.
 2012-02-07 02:25:31 -05:00
Stacey Sheldon
3c1b1001f9 f4 usb: Allow USB descriptors to be const through ST APIs 2012-02-07 02:25:31 -05:00
Stacey Sheldon
56102013aa f4 usb: correct function prototypes in bsp template 
This file is not actually used but it should still be accurate.
 2012-02-07 02:25:31 -05:00
Stacey Sheldon
57f9f6e3d1 f4 usb: configure and build ST USB OTG and USB DEV libraries 2012-02-07 02:25:31 -05:00
Stacey Sheldon
1e79ed6d54 f4 usb: fix invalid reference to stm32f4_discovery.h 2012-02-07 02:25:31 -05:00
Stacey Sheldon
04b81f13a7 f4 usb: fix invalid references to stm32f2xx.h 2012-02-07 02:25:31 -05:00
Stacey Sheldon
266b95561f f4 usb: rename device template to real config file 2012-02-07 02:25:30 -05:00
Stacey Sheldon
a4ae844f2b f4 usb: rename otg template to real config file 2012-02-07 02:25:30 -05:00
Stacey Sheldon
58bbe0870d f4 usb: allow device->host data to be const 
This allows the application code to pass const
descriptors to the Tx APIs in the STM32 USB
library.
 2012-02-07 02:25:30 -05:00
Stacey Sheldon
4b911bb3be f4 usb: remove unused device class examples 2012-02-07 02:25:30 -05:00
Stacey Sheldon
efbe8bbfdd f4 usb: convert all line endings to LF-only 
Line ending changes only.  No functional changes.
 2012-02-07 02:25:30 -05:00
Stacey Sheldon
6a43d1c7ed f4 usb: Import pristine STM32F4 USB Library v1.1.0 
Taken from version STM32F4-Discovery_FW_V1.1.0 of the
library from ST.
 2012-02-07 02:25:30 -05:00
Stacey Sheldon
240425ff22 gdb: add config file for revo bl 2012-02-07 02:25:30 -05:00
Stacey Sheldon
1532338847 ef: fix dependencies in entire flash image build 
ef_$(BOARD_NAME).bin files were not properly depending
on their fw and bl files resulting in the ef files not
being regenerated.
 2012-02-07 02:25:30 -05:00
James Cotton
ae01936808 Add the portTickTime into the OveroSync stream 2012-02-06 10:00:02 -06:00
James Cotton
dbcb499d7f Add object to monitor the overo link status. Current just records the bytes/s 
being sent and the connected status (based on sending more than 500 bytes per
second)
 2012-02-06 09:37:31 -06:00
James Cotton
5b2376dbee Remove the semaphore for buffer swapping and make this occur during the receive 
ISR.  This leads to a possible condition where a copy is taking place in
userspace and then a buffer swap interrupts it.  However, the copy should
always finish before the SPI DMA slave catches up to that place in memory at 10
MHz.

This fixes a common condition where the userspace task (low priority) was not
swapping buffers in time from user space and logs were corrupted.
 2012-02-06 08:21:24 -06:00
James Cotton
179e66b754 Refactor how new packets are scheduled to avoid trying to start a transaction 
from an ISR.  This was causing lock ups.  It's a bit higher latency probably
(trivially slow) but if we aren't keeping up with the Overo transactions then
using a proper DMA double buffer will be required.
 2012-02-04 20:11:31 -06:00
James Cotton
665801662d In cc3d update sensors add accelbias before scaling to allow more precision in 
levelinIn cc3d update sensors add accelbias before scaling to allow more
precision in levelingg
 2012-02-04 12:12:41 -06:00
James Cotton
4e190f99e2 Improved the revo overosync code to put multiple uavobjects into a packet 2012-02-04 12:06:03 -06:00
Stacey Sheldon
60a2af2e58 ef+dfu: Move EF image generation into separate makefile 
A separate makefile for EF (Entire Flash) targets allows
the removal of board-specific hard-coded addresses.  These
values can now be included from the board-info.mk files
for each board.
 2012-02-04 12:03:42 -05:00
Brian Webb
3f66afd74a Removed emacs mode header from pios_gcsrcvr.c 2012-02-04 08:42:16 -07:00
Stacey Sheldon
4fafbb13ed makefile: Add EF (Entire Flash) targets for all boards 
These new build targets will construct a flash image that
includes both a bootloader as well as a firmware image all
in one.  Examples:
  make ef_coptercontrol
  make ef_revolution

This also adds support for a new target for writing this EF
image to boards that support a DFU interface (only F4-based
boards).  This can be done by running:
  make dfuutil_install
  # Boot board with SBL asserted to activate STM32 DFU ROM
  # Attach USB cable
  make ef_revolution_dfu

Bootloader images are also now padded out to occupy the full
BL flash region.
 2012-02-03 00:59:36 -05:00
Stacey Sheldon
ce544cf4ab gdb: remove cortex_m3 remnants from revo gdb init file 2012-02-03 00:59:31 -05:00
Stacey Sheldon
99f5f20cb2 openocd: add support for stlink on stm32f4 targets 2012-02-03 00:51:31 -05:00
Brian Webb
a314604f9b Added failsafe to GCS Receiver device. 2012-02-02 19:59:42 -07:00
James Cotton
18a64e261f Going a bit overkill with this - deinit who SPI block between transactions. 2012-02-02 12:32:57 -06:00
James Cotton
c26154f303 Switch back to 256 byte packets and 0xFF pad the end 2012-02-02 11:40:49 -06:00
James Cotton
03cfb1453a DeInit SPI DMA between transactions. Somehow if this doesn't happen the next 
transaction doesn't start at the beginning again.  Something is still not quite
right because first few bytes aren't getting across.  Need logic analyzer.
 2012-02-02 11:37:35 -06:00
James Cotton
77a6abb341 For PIOS_SPI F4 do not enable the TX irq. Also do not wait for the 
transmission to finish either.
 2012-02-02 11:24:14 -06:00
James Cotton
8b1137c6a0 Align the tx and rx SPI buffers from Overosync 2012-02-02 11:23:40 -06:00
James Cotton
0a71a48c57 Sending all FF finally again 2012-02-02 10:36:09 -06:00
James Cotton
80b839d145 The SPI3 TX DMA channel was wrong 2012-02-02 10:13:09 -06:00
James Cotton
29237f97ae For SPI slave devices we need to handle the interrupt differently since 
transactions should already be completed.  Also reset the callback so in the
case of noise on the IRQ line it will not keep firing interrupts.

I suspect we should probably disable interrupts in this handler to prevent
refiring.
 2012-02-02 10:13:09 -06:00
James Cotton
88b9f20cda Fix nasty bug in the DMA stream configuration 2012-02-02 10:13:09 -06:00
James Cotton
95abb56d5e Added module to send updates out the SPI port 2012-02-02 09:19:25 -06:00
James Cotton
e434ab94a9 Enable SPI port for revolution to overo communications 2012-02-02 01:42:38 -06:00
Alessio Morale
5449408763 Merge branch 'amorale/timerprescaler' into inoutch8 2012-02-01 00:23:53 +01:00
Alessio Morale
cb2dadd0ea fix Motor 8 out not working 2012-02-01 00:20:50 +01:00
Alessio Morale
322ced44a1 Solve PWM Input 8 not working 2012-02-01 00:16:48 +01:00
Alessio Morale
820e8ac062 Handle different prescaler values for timers on APB1 and APB2. 
The PIOS_MASTER_CLOCK has been removed in favor of
PIOS_SYSCLK (the master clock value,168000000 for revolution)
PIOS_PERIPHERAL_APB1_CLOCK and
PIOS_PERIPHERAL_APB2_CLOCK
Look at STM32F4xx_Revolution.h for the list of timer/peripheral and APB them belongs.
 2012-01-28 20:04:55 +01:00
James Cotton
a778c45d6f For L3GD20 sensor task run at the sensor speed 2012-01-28 10:11:30 -06:00
James Cotton
13447ac907 Fix the MPU6000 implementation 2012-01-28 00:21:58 -06:00
James Cotton
e07fca0465 Commit the revolution board_hw_defs.c file 2012-01-26 23:32:36 -06:00
James Cotton
b4435d0b35 For L3GD20 sensor task on revo update gyro once per physical sample 2012-01-26 23:29:12 -06:00
James Cotton
f311700804 Flashfs: Whenever failing out of a transaction unlock the semaphore 2012-01-26 14:14:50 -06:00
James Cotton
85bfa7dcf9 Flashfs: Missed calculation of the header crc for monolitihic write 2012-01-26 13:32:53 -06:00
James Cotton
84dd1dbc40 A bit more lenient settings for CC sensor timings 2012-01-26 13:00:06 -06:00
James Cotton
ad3d470f40 Flashfs and Flash: Add new function to write a series of blocks in one flash 
write transaction to improve efficieny.
 2012-01-26 12:39:35 -06:00
James Cotton
80705cdba1 Flash: Because on CC/CC3D the flash is initialized before FreeRTOS is started 
we cannot use the transaction lock or the delay while saving.
 2012-01-26 11:50:05 -06:00
James Cotton
4fc907ad0d Add a transaction semaphore to flash and flashfs to make sure multiple saves 
or loads can't be attempted between threads
 2012-01-26 11:36:07 -06:00
James Cotton
8b15fdd88b Flash: Add a vTaskDelay when waiting for flash operations to complete to 
prevent blocking the bus from accels
 2012-01-26 11:26:19 -06:00
James Cotton
7f38d113eb Delete more old target stuff 2012-01-26 11:21:34 -06:00
James Cotton
e69a0937bc Flash: Wrote status instead of read it 2012-01-26 11:17:00 -06:00
James Cotton
69dc5abf0c Flash: Get rid of some defines and directly reference the cfg structure 2012-01-26 10:56:26 -06:00
James Cotton
6d572986e5 Flashfs: Clean up some of the JEDEC commands and also format whole chip when FS 
is wrong.
 2012-01-26 10:04:49 -06:00
James Cotton
fe7b9a909a LED: Update the LEDs on revo 2012-01-26 09:11:27 -06:00
James Cotton
7eab883d5c Fix some small revolution typos 2012-01-25 22:50:19 -06:00
James Cotton
20670d049b Update pios_led for F4 targets to match the new F1 implementation. Also fix 
type for F1 in GPIO labels.
 2012-01-25 22:50:19 -06:00
James Cotton
727f0befc5 Make the gyro go a bit more regularly to stabilization but needs updating 
regular CC
 2012-01-25 22:50:19 -06:00
James Cotton
e4df3202e0 L3GD20: Update sensor task for revo to use the new queue 2012-01-25 22:50:19 -06:00
James Cotton
205aabe895 L3GD20: Make this sensor push data onto a FreeRTOS queue so that the sensor 
reading task can block according.  Also now the gyro data is sent to
stabilization multiple times per update of the attitude loop.
 2012-01-25 01:20:07 -06:00
James Cotton
0da20bb846 Flash: Because most of the commands are a JEDEC standard rename this file 
pios_flash_jedec and abstract out the methods that can vary between chips.
 2012-01-25 00:23:24 -06:00
James Cotton
a02cad6f52 Flashfs: Separate out the sector sizes and magic values into a runtime 
configurable structure.  This makes it easier to deal with different chip
layouts.
 2012-01-24 23:56:59 -06:00
James Cotton
1971ba30dc No longer hardcode baudrate 2012-01-24 23:42:43 -06:00
James Cotton
5ad37e691c USB: Update the USB configuration structure to include the GPIO that is used 
for sensing and then load different config for CC and CC3D.  Updated the
bootloader as well.  Also changed the PIOS_USB_CheckAvailability function to
only return the sense signal and not the transfer_possible flag as this is not
set in time for the bootloader on CC3D for some reason.
 2012-01-24 22:15:43 -06:00
James Cotton
bc3703ce33 Need more irq stack for CC3D 2012-01-24 19:48:52 -06:00
James Cotton
104c091590 Correct the range constants for the L3GD20 driver 2012-01-24 19:48:14 -06:00
James Cotton
a25d52785b Change the bus speed for the L3GD20 to 10MHz and some small cleanups 2012-01-24 19:17:49 -06:00
James Cotton
3880b0ddc3 CC3D and CC use different CS lines for the flash chip. Add a second cfg 
structure for each SPI interface.
 2012-01-24 16:21:48 -06:00
James Cotton
587ec5a615 Revert earlier patch on filesystem for Revolution. Need to make erase command 
and positioning of filesystem dependent on board type.

Reverted 99123372d0
 2012-01-24 16:14:41 -06:00
James Cotton
b6c056fef2 Use the updated L3GD20 format and make attitude.c use the gyro data from the 
fifo
 2012-01-24 15:52:17 -06:00
James Cotton
c9263cb8c0 L3GD20: Dynamically allocate buffer structure when used 2012-01-24 15:51:38 -06:00
James Cotton
5efbfb02fa Make the BMA180 sensor system acquire from the queue. Correct the orientation 
and speed it up to 10 MHz communications.
 2012-01-24 15:09:20 -06:00