Summary of changes:
* USB CDC and HID drivers are completely split apart.
* This will allow different max buffer sizes for HID and CDC.
* USB descriptors have been overhauled:
* Proper structs/macros/enums declared for USB (see pios_usb_defs.h)
* Two common descriptor definitions. One for HID+CDC another for HID only.
See pios_usb_desc_{hid_cdc,hid_only}.c for details.
* Long standing bugs in OP USB descriptors became much more obvious with the
new struct definitions.
* Board specific USB initialization is now in pios_usb_board_data.h in each build target.
* Definition of USB descriptors is now entirely indpendent of STM32 libs.
Glue into STM32 libs is provided by pios_usbhook.c.
* Removed a lot of stale/irrelevant USB #defines throughout the tree.
* Improved naming consistency throughout USB code:
* PIOS_USB_HID_* now refers to the HID endpoint code.
* PIOS_USB_CDC_* now refers to the CDC endpoint code.
* PIOS_USB_* now refers to the low-level USB code.
* PIOS_USB_BOARD_* now refers to board-specific USB data
* PIOS_USBHOOK_* is glue between PIOS and STM32 USB libs.
* struct usb_* and enum usb_* and USB_* and HID_* are all types from the USB spec.
* Shrunk the buffer size on the CDC call mgmt endpoint to save some RAM.
* Made a few more USB related variables static to save some RAM.
Allocate per-instance data for drivers from the heap
rather than as static variables from the .data segment.
This converts > 800 bytes of RAM from being always consumed
as static data into being allocated from the heap only when
a particular feature is enabled in the hwsettings object.
A minimal config (no receivers, flexi port disabled, main port
disabled) leaves 2448 bytes of free heap. That's our new baseline.
Approximate RAM (heap) costs of enabling various features:
+ 632 Serial Telemetry (includes 400 bytes of Rx/Tx buffers)
+ 108 PWM Rcvr
+ 152 PPM Rcvr
+ 112 Spektrum Rcvr
+ 24 S.Bus (Should be closer to 68 since driver is still using
static memory)
There are still some drivers that pre-allocate all of their memory
as static data. It'll take some work to convert those over to
dynamically allocating their instance data.
This allows the spektrum and sbus receiver drivers to bind
directly to the usart layer using a properly exported API
rather than overriding the interrupt handler.
Bytes are now pushed directly from the usart layer into the
com layer without any buffering. The com layer performs all
of the buffering.
A further benefit from this approach is that we can put all
blocking/non-blocking behaviour into the COM layer and not
in the underlying drivers.
Misc related changes:
- Remove obsolete .handler field from irq configs
- Adapt all users of PIOS_COM_* functions to new API
- Fixup callers of PIOS_USB_HID_Init()
priority preempts) and adjusting the priorities around to be more sensible.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2355 ebee16cc-31ac-478f-84a7-5cbb03baadba
but not having telemetry causes a reset. If the buffer got full enough it
would never start to transmit again.
Note: also making Telemetry non-blocking
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2346 ebee16cc-31ac-478f-84a7-5cbb03baadba
before because if transmission got NAK then sending would stop. Now the next
time data is added to the buffer a new send will be attempted.
fifoBuf: in clearData just set the read pointer to the write pointer. This is
safer for multiple people accessing it assuming the reader will be clearing it.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2279 ebee16cc-31ac-478f-84a7-5cbb03baadba
and starting transmission again. This should address the bootloader locking up
on verify.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2235 ebee16cc-31ac-478f-84a7-5cbb03baadba
similar driver format to the PIOS_USART system. (p.s. are you happy now, PT?)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2029 ebee16cc-31ac-478f-84a7-5cbb03baadba
running and block the interrupts while modifying the buffers
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2003 ebee16cc-31ac-478f-84a7-5cbb03baadba
1. Added reenumeration function and call it on USB init (device will appear after reprogramming now)
2. Moved buffer.c to general flight/Libraries location
3. Removed the 62 byte transmission limitation by adding a transmission buffer
4. Sped up USB communication by increasing endpoint polling frequency
Note, that the nonblocking and blocking USB send functions are not blocking entirely correcting. The blocking calls the nonblocking, and the nonblocking blocks until the last chunk has started tranmission if it's a big transmission. The buffering I added would generalize to non-blocking nicely, but would require using the EP1(IN) callback to handle most of the tranmission. This creates a lot of issues if one function is pushing data onto the buffer and the interrupt is sending.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1403 ebee16cc-31ac-478f-84a7-5cbb03baadba
The com layer transmit functions should provide guarantees
that they will not modify the buffer that you're transmitting.
Declaring the parameter as a pointer to const keeps the underlying
implementations honest.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1001 ebee16cc-31ac-478f-84a7-5cbb03baadba
- Created a pluggable COM layer
- Converted COM + USART init into static initializers
rather than typedefs
- Generalized the USB HID COM API to match the USART
API.
- Changed USART and COM layers to be data driven rather
than #ifdef'ing/switching on the specifics of each port
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@760 ebee16cc-31ac-478f-84a7-5cbb03baadba
This fixes the COM interface over USB HID to the point where
it can establish and maintain solid communications with the UAVObject
Browser in the GCS.
Tested only on Linux. The USB HID interface is still disabled for now
until it is tested successfully by a wider group.
Edit telemetry.c and set ALLOW_HID_TELEMETRY to 1 to enable telemetry
over the USB HID interface and report your results in the forum.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@656 ebee16cc-31ac-478f-84a7-5cbb03baadba
