Adds a new RCTransmitter setting for the USB HID interface which
emulates a USB HID joystick. The scaled RC receiver channels
from any RCVR protocol are passed through to the various emulated
joystick controls.
The main use for this feature is to allow you to use your own RC
transmitter with any RC simulator on a PC.
This is known to work with CRRCsim but should work with any simulator
that supports joystick input.
BL images now always use hid-only.
FW images can use hid-only or hid+vcp but this is selected
ONLY at compile time based on whether PIOS_INCLUDE_USB_CDC
is defined.
CC uses HID+VCP by default now.
Now that we have a USB descriptor for HID+VCP that works
on Ubuntu 11.10, MacOS 10.7.3, Win7-SP1-32bit,
WinXP-SP3-32bit, Win7-SP1-64bit.
VCP is known to not work on WinXP without service pack 3.
Support for receiver configuration (PPM, PWM and DSM)
There are still problems with Flexi port (not sure if related to a problem with my board) and Uart/SBUS that has the input always inverted.
This module and its associated settings uavo can be used
to test various fault conditions during initialization.
To enable the module, add the TEST_FAULTS=YES to your make
command line:
make fw_coptercontrol TEST_FAULTS=YES
Once this module is part of your firmware load, you can
enable it in the hwsettings uavo and then select the
type of fault to insert by editing the faultsettings uavo.
On the next reset, the configured fault will be inserted
into the init sequence to allow you to test the boot fault
recovery code.
With a fault inserted, you should see 3 failed boot attempts
followed by a successful (recovery) boot. You will see the
BootFault alarm set to Critical, and the RAM version of your
hwsettings will be reset to defaults. Since the defaults have
all optional modules disabled, the fault module will be out of
the way during the recovery boot.
You can then "Load" the flash version of the hwsettings uavo
in the object browser, disable the Fault module and then "Save"
the hwsettings module back to the board. The next reset will
boot normally without the fault inserted.
This allows the HID and VCP functions to be configured
separately so that additional functions can be more easily
bound to the VCP port.
This change also provides a safety net that forces either
the HID or VCP to be configured for USB Telemetry. This
safety net may vanish in the future once the GCS can check
it. Disabling USB Telemetry entirely would save more than
400 bytes of RAM.
- both CC serial ports are now disabled by default (no telemetry);
- serial ports now have DSM2, DSMX (10bit) and DSMX (11bit) options;
- ReceiverGroups now have DSM (MainPort) and DSM (FlexiPort) options.
For DSM2 protocol there is an explicit resolution bit in the stream, so
the DSM2 should be selected. For DSMX there is no such bit, and user
should choose the resolution from the list configuring the spektrum port.
ReceiverGroups have single DSM option which is handled by the same driver.
Downside: this implementation saves received frame first, unrolls by the
end of frame. This should be ok, but may be improved by unrolling channels
on the fly in the rx callback.
Another minor difference is that a ChannelGroup is now bound to port:
DSM (MainPort) or DSM (FlexiPort). This was considered as acceptable
solution in order to not have 6 DSM options for each ChannelGroup and
even more in case of new DSM protocol variations.
Known problem: it is not possible to choose same protocols like
DSM2/DSM2 for two ports. It can be enabled by adding an exception to
common rule, though.
The DSMX throttle channel misbehavior (zero value) is not treated
specially yet. It should trigger the failsafe being out of bounds.
More info and data dumps are required to handle this properly.
PPM. This saves resources. Good suggestion Os. In this configuration we
could allow 12 channels of output but for now I'll leave it capped at 10 to
lessen resources on the mixer table.
With spektrum and camera stab enabled there was
1632 bytes heap remaining
180 bytes irq stack remaining
TelemetrySettings object removed (saved 200+ bytes of RAM). Telemetry
port speed moved to the HwSettings object. Added GPS port speed setting.
GCS code updated to reflect changes and support both fields.
This module will periodically update values of stabilization PID settings
depending on configured input control channels. New values of stabilization
settings are not saved to flash, but updated in RAM. It is expected that the
module will be enabled only for tuning. When desired values are found, they
can be read via GCS and saved permanently. Then this module should be
disabled again.
