The pipxtreme boards use a sector of the on-board flash
for configuration storage. Adjust the memory maps to
reflect this.
The board_info_blob is also extended to include the EE
bank definitions. This should be used by the pipxtreme
firmware rather than determining it based on chip size.
The board info blob is stored in the last 128 bytes of the
bootloader's flash bank. You can access this data from the
application firmware like this:
#include <pios_board_info.h>
if (pios_board_info_blob.magic == PIOS_BOARD_INFO_BLOB_MAGIC) {
/* Check some other fields */
}
DO NOT link pios_board_info.c into your application firmware.
Only bootloaders should provide the content for the board info
structure. The application firmware is only a user of the data.
AHRS_comms still needs to be implemented. INS/GPS functionality still needs to be implemented. Double-check of the new drivers still needs to be done.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@3162 ebee16cc-31ac-478f-84a7-5cbb03baadba
- Removed all unnecessary device instances and their cfg's.
- SPI to SD card
- I2C
- Aux USART
- Moved SPI baudrate setting into cfg rather than init func.
- Abstracted forcing slave select under OPAHRS API.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2786 ebee16cc-31ac-478f-84a7-5cbb03baadba
functions to use it easily
Conflicts:
flight/Modules/Attitude/attitude.c
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2707 ebee16cc-31ac-478f-84a7-5cbb03baadba
The UAVObject initcall list is now automatically
generated at link time based on the exact set of
UAVObjects linked into the firmware image.
This will allow any subset of UAVObjects to be
used in any firmware image.
The uavobj_initcall() macro automatically adds the
marked function's address into the .initcalluavobj.init
ELF section.
The UAVObjectsInitializeAll() function now simply
iterates over the functions listed in the
.initcalluavobj.init section and calls them.
You can see the contents of this section in the ELF file
like this:
./tools/arm-2009q3/bin/arm-none-eabi-objdump \
--syms -j .initcalluavobj.init \
./build/openpilot/OpenPilot.elf
This is fundamentally the same mechanism that the Linux
kernel uses to initialize the specific set of components
that the user has selected in their kernel configuration.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2630 ebee16cc-31ac-478f-84a7-5cbb03baadba
only one CS line is asserted. No checks are enforced on this by the SPI code
as I cant see a clean way of it being aware of the CS lines. We could add
another CS mode those which is driver managed per transfer and has a GPIO i
line for each device.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2579 ebee16cc-31ac-478f-84a7-5cbb03baadba
Beginning of unifying the input types into PIOS_RECEIVER.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2568 ebee16cc-31ac-478f-84a7-5cbb03baadba
accounting for the fact they are transferred in pairs when using ADC2
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2510 ebee16cc-31ac-478f-84a7-5cbb03baadba
gyro data into attitude raw. Hardcoded calibration for now.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2474 ebee16cc-31ac-478f-84a7-5cbb03baadba
1) Added nack counter monitoring
2) Made timeout for getting semaphore in I2C user space code use the one from
driver and record timeouts. This does not influence timeouts in the non
FreeRTOS case
3) Remove case block from the error handler so that all bus errors reset the
i2c interface
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2469 ebee16cc-31ac-478f-84a7-5cbb03baadba
size (may eventually need to be per revision if we get bigger ram). Typo in a
the ifdefs to get allow disabling SDCARD
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2423 ebee16cc-31ac-478f-84a7-5cbb03baadba
are logged, and separately the erirq and evirq logs are exported
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2368 ebee16cc-31ac-478f-84a7-5cbb03baadba
ActuatorSettings although for PWM aircrafts it should be done exactly as before
Actuator: Store the update times and maximum update time
OP-14 I2C: Start tracking short history of events and states in driver for
logging
OP-237 Flight/Actuator: Support for I2C based ESCs
OP-237 MK_ESC: Send all four motors as one atomic transfer
OP-237 Flight/Actuator: Allow channels to be mapped to MK I2C interface. Currently
mixer channels are either PWM or MK but in the future this will change to
support more than 8 channels.
OP-16 PiOS/I2C: Further work to try and make I2C more stable, mstly special case
handline in IRQ
OP-237 I2C ESC: Support for Astect 4 channel ESCs
OP-237: When the I2C Actuator write update fails track this
OP-237 Actuator Settings: Change the way motor types are selected to keep that
information more appropriately within ActuatorSettings instead of MixerSettings
Also make motors stay at or above neutral when armed and throttle > 0
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2366 ebee16cc-31ac-478f-84a7-5cbb03baadba
tasks directly update a flag for each module (which they register) and when all
flags set clear the watchdog then.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2365 ebee16cc-31ac-478f-84a7-5cbb03baadba
sometimes thrown, and made errors not lock it up by default. It works for me,
but since this has historically been associated with lots of lock ups please
check your systems carefully.
PiOS/I2C: Make the bus by default try to recover from errors instead of locking
up
PiOS/I2C: After a bus error and clocking all previous data create a STOP
condition to make sure bus is released (note, this also requires creating a
START condition first)
PiOS/I2C: If the same event hits the I2C bus twice in a row then disregard
second one, there is no situation where we should get the same event multiple
times that matters and this gets us out really quickly to catch the real
events. I was seeing this with repeated 0x70084 which means byte transmitted.
This is related to STM32 bugs in the IRQ timings I believe.
PiOS/I2C: 1) Mask out some bits we don't care about in the event flags
2) Don't lock up if the give semaphore fails, although why it does is strange
3) Recover from bus failure through the "auto" state path instead of just
coding state
PiOS/I2C: Change the reset bus code to follow
http://www.analog.com/static/imported-files/application_notes/54305147357414AN686_0.pdf
(thanks for the reference Neontangerine). Although this may actually NOT clear
the bus the first time through, subsequent bus errors should eventually clock
it out. The up side is it is less likely to clock a bunch of 1s into an ESC
and make it run up.
PiOS/I2C: Some cleaned up code for getting a snippet of the history when
something strange happens
PiOS/I2C: Export logging information from I2C through a UAV object
PiOS/I2C: Improve the diagnostic information
PiOS/I2C: Need to handle the event 0x30084. This seems to happen between a
byte transmitted and new byte started
PiOS/I2C: Handle the NACK condition by simply going to the stopping state.
PiOS/I2C: Add a new NACK state to handle sending the STOP signal after a NACK
following the STM documentation. Other error conditions still are not dealt
with.
PiOS/I2C: Should handle the NACK condition from all the write cases. Need to
think about read cases
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2239 ebee16cc-31ac-478f-84a7-5cbb03baadba
Flight: Create PositionDesired (the active waypoint) UAVObject and make the FlightSituationActual no update since it not used.
Flight: New velocity desired object that passes information between the look computing the desired velocity and the PID loop to get it (updated at different rates)
UAVObjects/PositionActual: Remove unused GPS fields
UAVObjects/PositionActual VelocityActual: Split the velocity into a separate object. ALso make sure all the information telemetered around is in cm to avoid using floats.
UAVObject/GuidanceSettings: New guidance settings object for the guidance module
Flight/Posix: Add the new objects to the Posix sim
Flight/Guidance: Computes a desired velocity based on position error than runs a PID loop to control roll and pitch to achieve that velocity. All distances are in cm, and updated the PositionActual fields to reflect this and use int32.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1760 ebee16cc-31ac-478f-84a7-5cbb03baadba
determine retransmitting calibration, home location and such.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1755 ebee16cc-31ac-478f-84a7-5cbb03baadba
Calibration should take less time now too (using second moments to estimate
variance in one pass). Now need to change to multiple messages to get the
calibration in to keep the request message size minimal. Also currently
running sensor calibrate doesn't store the gyro bias so if you want to use this
you'll have to tweak it manually. I'll fix that step tomorrow.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1741 ebee16cc-31ac-478f-84a7-5cbb03baadba
Way too much was being exposed in the API for the
HMC5843. This commit properly hides internal
details of the driver.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1629 ebee16cc-31ac-478f-84a7-5cbb03baadba
The DRDY signal from the magnetometer is connected to PB8
on the STM32. This pin is now configured as an external
interrupt and is now used to signal when new data is
available from the magnetometer.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1628 ebee16cc-31ac-478f-84a7-5cbb03baadba
I2C bus errors are now recoverable. The bus is properly reset
and an error indication is now provided to the caller whenever
a bus error occurs during processing of the transaction list.
For now, the users of the I2C layer just retry infinitely on
failure. The BMP085 and HMC5843 code should be changed to
report errors to its callers to allow a more sensible retry
strategy.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1625 ebee16cc-31ac-478f-84a7-5cbb03baadba
The info field in the pios_i2c_txn list can now be used
to provide a const string which describes the context
for this transaction.
This is very helpful when diagnosing an error that occurs
somewhere in the middle of the I2C FSM since the FSM runs
primarily in the ISR where the original context for the
transactions is no longer available in the traceback.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1622 ebee16cc-31ac-478f-84a7-5cbb03baadba
Differentiate the _FSM_ faulted from the (soon to
exist _BUS_ faulted state.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1621 ebee16cc-31ac-478f-84a7-5cbb03baadba
Implement low-level utility functions for sending/receiving
the opahrs proto v0 (bootloader) messages. These are used
by the OP firmware loader and the AHRS bootloader.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1586 ebee16cc-31ac-478f-84a7-5cbb03baadba
This cleans up some of the boiler plate code that is
repeasted for simple (empty) requests that expect a
response.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1584 ebee16cc-31ac-478f-84a7-5cbb03baadba
No functional changes. Whitespace/tab fixups only.
Use TRUE/FALSE instead of 1/0.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1430 ebee16cc-31ac-478f-84a7-5cbb03baadba
1. Added reenumeration function and call it on USB init (device will appear after reprogramming now)
2. Moved buffer.c to general flight/Libraries location
3. Removed the 62 byte transmission limitation by adding a transmission buffer
4. Sped up USB communication by increasing endpoint polling frequency
Note, that the nonblocking and blocking USB send functions are not blocking entirely correcting. The blocking calls the nonblocking, and the nonblocking blocks until the last chunk has started tranmission if it's a big transmission. The buffering I added would generalize to non-blocking nicely, but would require using the EP1(IN) callback to handle most of the tranmission. This creates a lot of issues if one function is pushing data onto the buffer and the interrupt is sending.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1403 ebee16cc-31ac-478f-84a7-5cbb03baadba
This is to align the object names to matches the UAVObject
architecture doc. No functional changes.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1351 ebee16cc-31ac-478f-84a7-5cbb03baadba
Since the i2c bus is bidirectional, there are certain
states (eg. part way through a read) where the slave
device is in control of driving the SDA line.
On a cold start (power on), the slave devices are all
quiescent and will not drive the bus. However, on a warm
start (eg. watchdog or jtag restart), it is possible that as
the CPU boots, the slave device may be holding the SDA line
low. This is a bus busy condition and will prevent the I2C
bus master in the CPU from being able to seize the bus during
init.
The fix for this is to clock the i2c bus sufficiently to ensure
that the the slave device finishes its transaction and releases
the bus.
Once the slave has released the bus, the bus master can properly
initialize and assert a STOP condition on the bus.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1349 ebee16cc-31ac-478f-84a7-5cbb03baadba
into NED reference frame and used in the INSGPS algorithm, although currently this
information isn't propagated back to OP. Data structures related to the GPS position
into the algorithm and the position estimate out will likely be in flux.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1334 ebee16cc-31ac-478f-84a7-5cbb03baadba
Altitude/pressure sensor data is sent to the AHRS whenever
the AltitudeActual object is updated.
Altitude, Pressure and Temperature are sent as floats.
Same as in the UAVObject that goes to the GCS.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1291 ebee16cc-31ac-478f-84a7-5cbb03baadba
The STM32 I2C block has a number of errata associated with it.
These errata are primarily related to timing sensitivities between
the peripheral and the interrupt handler. In particular, the
correct generation of the stop bit relies on the I2C IRQ running
immediately and not being held off for any reason.
NOTE: The I2C interrupts must be the highest priority IRQs in the
system to ensure correct operation.
I2C protocol is now implemented as a formal state machine.
See: stm32_i2c_fsm.{dot,jpg} for FSM description.
I2C init is now expressed by const initializers in pios_board.c
for both OP and AHRS boards.
I2C device drivers (ie. bmp085/hmc5843) now pass in const arrays
of an unlimited number of bus transfers to be done atomically.
The I2C adapter driver now handles all bus-level locking across the
list of transactions. Generation of start/restart/stop conditions
are handled automatically over the list of transactions.
Timeouts have been removed from the API for now. May be added
back later.
This driver has run error free on both the OP and AHRS boards for
up to 48hrs but it still sometimes fails earlier than that on the OP
board. There is another possible set of improvements to the driver
that could employ the DMA engine for transfers of >= 2bytes. This
change would reduce the timing sensitivities between the peripheral
and the driver but unfortunately, both the SPI and I2C interfaces
share the DMA1 engine. That means only one of these two peripherals
can use the DMA engine and right now, SPI between OP and AHRS is
already using it.
Failures are currently fatal and will lock up the CPU. This allows
useful information to be obtained in the failure cases.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1241 ebee16cc-31ac-478f-84a7-5cbb03baadba
The AHRS comms module now sync's with the AHRS and
exchanges interesting data periodically. Whenever
the link to the AHRS is down, the AHRSComms alarm is
raised.
This is fairly basic for now but provides the last
piece of the infrastructure to move data back/forth
between the OP and the AHRS.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1014 ebee16cc-31ac-478f-84a7-5cbb03baadba
PIOS SPI devices may now make use of automatic CRC generation
and checking on block transfers. Only supports CRC8 for now.
Since the SPI interface CRC calculation continues across message
boundaries (ie. not reset on every transfer), we must manually reset
the CRC registers for every transfer to allow the two sides of the
link to resynchronize.
Unfortunately, resetting the CRC registers requires disabling the
SPI peripheral which must now be done on every block transfer.
Note: The last byte of the tx buffer is never sent and is assumed to
be a place holder for the tx CRC8.
Note: The last byte of the rx buffer is expected to hold the rx CRC8.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1011 ebee16cc-31ac-478f-84a7-5cbb03baadba
Tx buffers should not be modified. This allows passing const data
to the transfer function.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1010 ebee16cc-31ac-478f-84a7-5cbb03baadba
This defines the SPI message format as well as a few
initial messages for moving data across the link.
The v0 messages are place holders for firmware download
in the bootloader.
The v1 messages are to be used by the main application.
Note: This is not the final protocol definition.
Subject to change without notice.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1004 ebee16cc-31ac-478f-84a7-5cbb03baadba
The com layer transmit functions should provide guarantees
that they will not modify the buffer that you're transmitting.
Declaring the parameter as a pointer to const keeps the underlying
implementations honest.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1001 ebee16cc-31ac-478f-84a7-5cbb03baadba
- Created a pluggable COM layer
- Converted COM + USART init into static initializers
rather than typedefs
- Generalized the USB HID COM API to match the USART
API.
- Changed USART and COM layers to be data driven rather
than #ifdef'ing/switching on the specifics of each port
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@760 ebee16cc-31ac-478f-84a7-5cbb03baadba
Added support for SPI slave configurations to the pios SPI layer.
Converted the board specific configuration for the PIOS SPI layer to
use const static initializers rather than #defines (see pios_board.c).
SPI interface between the OP board and the AHRS is now operational at
a basic level, capable of moving simple single byte messages between
boards. Multi-byte, CRC protected messages will be added on top of this.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@759 ebee16cc-31ac-478f-84a7-5cbb03baadba
- New Attitude module for AHRS (skeleton)
- New AttitudeSettings UAVobject
- New AttitudeActual UAVobject
- Regenerated UAVobjects
- Added new UAVobjects to OpenPilot and GCS builds
- New PiOS driver for OpenPilot AHRS (stubs only)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@655 ebee16cc-31ac-478f-84a7-5cbb03baadba
This module reads from the BMP085 pressure sensor. It periodically
updates the pressure (kPa) and temperature (C) as well as the
calculated altitude (m).
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@640 ebee16cc-31ac-478f-84a7-5cbb03baadba
FreeRTOS has a strict requirement that even interrupt-safe API calls (ie.
those ending in "FromISR") can only be called from ISRs that are at lesser
or equal priorities to configMAX_SYSCALL_INTERRUPT_PRIORITY. See the
"configKERNEL_INTERRUPT_PRIORITY and configMAX_SYSCALL_INTERRUPT_PRIORITY"
section at:
http://www.freertos.org/a00110.html
The interrupt numbers used on the Cortex-M3 CPU has a somewhat backward
representation of the interrupt numbers so 255 = lowest priority and
0 = highest priority.
The calculation is further complicated by the STM32 implementation only using
the upper 4 bits of the priority value. Only 0x00, 0x10, 0x20, ..., 0xE0, 0xF0
represent useful interrupt priorities.
FreeRTOS requires that MAX_SYSCALL and KERNEL interrupt priorities are expressed
as raw unshifted 8-bit values to be programmed directly into the BASEPRI register.
The priority values passed to the NVIC initialization, however, are expected
to be 4-bit values and are shifted up by 4 within NVIC_Init() for you.
The end result is that we need this arrangement:
[highest priority]
NVIC_0 (Non-maskable-interrupt)
NVIC_1
NVIC_2
[Must NOT call FreeRTOS APIs above here]
configMAX_SYSCALL_INTERRUPT_PRIORITY (now at 48 = 0x30 = NVIC_3)
PIOS_IRQ_PRIO_HIGHEST (cur. NVIC_4)
PIOS_IRQ_PRIO_HIGH (cur. NVIC_5)
PIOS_IRQ_PRIO_MID (cur. NVIC_8)
PIOS_IRQ_PRIO_LOW (cur. NVIC_12)
configKERNEL_INTERRUPT_PRIORITY (240 = 0xF0 = NVIC_15)
[lowest priority]
The previous config had configMAX_SYSCALL_INTERRUPT_PRIORITY set at
191 (0xBF) which is effectively NVIC_11. This was allowing all of
the MID, HIGH and HIGHEST interrupt handlers to preempt the OS in
its critical sections. Since some of these ISRs were calling
FreeRTOS APIs, this would result in corrupting internal data structures
within the OS.
It should be ok to move the configKERNEL_INTERRUPT_PRIORITY to a higher
priority as long as it is less than configMAX_SYSCALL_INTERRUPT_PRIORITY.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@637 ebee16cc-31ac-478f-84a7-5cbb03baadba
PIOS_SYS: Added system reset function.
OpenPilot Makefile: Default USE_BOOTLOADER should be NO.
OpenPilot Bootloader: Removed LED initialisation.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@303 ebee16cc-31ac-478f-84a7-5cbb03baadba
Added timer usage diagram to pios_board.h
Removed bloat for extra optimisation in PIOS_DELAY.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@265 ebee16cc-31ac-478f-84a7-5cbb03baadba
You can now send and receive packets (up to 63 bytes) just like using the USART port with PIOS_COM.
HID packet length will soon be increased to support maximum UAVTalk message length.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@182 ebee16cc-31ac-478f-84a7-5cbb03baadba
Added working preliminary PIOS_USB_HID support.
Integrated PIOS_USB_HID support into PIOS_USB_HID.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@171 ebee16cc-31ac-478f-84a7-5cbb03baadba
Added PIOS_USB.
Global improvements, see specific files for changes.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@144 ebee16cc-31ac-478f-84a7-5cbb03baadba
Startup procedure now waits for SD Card with the correct settings files on it.
Refactored a few global PIOS_SDCARD names.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@140 ebee16cc-31ac-478f-84a7-5cbb03baadba
Made minGlue even more robust and simpler.
Fixed a small bug with the servo output code, which is now working 100%.
Enabled USART, which can now be used for debugging.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@138 ebee16cc-31ac-478f-84a7-5cbb03baadba
Changed bootup procedure for how the SD Card is handled.
Completed, optimised and added error handling to minGlue.c
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@137 ebee16cc-31ac-478f-84a7-5cbb03baadba
This revision is a good fall-back point as a basic test that the hardware and your development environment is working.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@133 ebee16cc-31ac-478f-84a7-5cbb03baadba
SD Card fixed and working, tested with 2Gb and 8Gb (SDHC) cards.
Changed startup_stm32f10x_HD.S to work with SysTick_Handler, needs to be changed back for FreeRTOS to work.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@132 ebee16cc-31ac-478f-84a7-5cbb03baadba
Added temporary flashing function as an easy way to know things are working.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@131 ebee16cc-31ac-478f-84a7-5cbb03baadba
init function will also try to access a file on the SDCard, this forces a real mount and will get real errors which we can handle.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@100 ebee16cc-31ac-478f-84a7-5cbb03baadba
Add some comments to pios.c so people know where the settings are loaded.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@84 ebee16cc-31ac-478f-84a7-5cbb03baadba
One major timing caveat still exists, still deciding the best way to cross that bridge.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@63 ebee16cc-31ac-478f-84a7-5cbb03baadba
Started work on BMP085 driver. Need more information from Bosch to continue.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@61 ebee16cc-31ac-478f-84a7-5cbb03baadba
New standard to be used is PIOS_Module_Function().
Likewise with OpenPilot, OP_Module_Function() is to be used.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@59 ebee16cc-31ac-478f-84a7-5cbb03baadba
