1
0
mirror of https://bitbucket.org/librepilot/librepilot.git synced 2024-12-12 20:08:48 +01:00
Commit Graph

40 Commits

Author SHA1 Message Date
sambas
f3bce1705b OP-22 Flight/PiOS: Spektrum fix, OP tested on ground not flown yet, CC not tested.
pios_rcinput.[ch] outdated

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2775 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-13 13:10:02 +00:00
stac
66a9d53d0a hwinit: Convert I2C driver to dynamic init
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2773 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-12 22:19:54 +00:00
stac
3fda65c5d3 hwinit: Convert SPI drivers to dynamic init
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2772 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-12 22:19:50 +00:00
stac
841b0d3d6d hwinit: Convert COM and USART to dynamic init
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2771 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-12 22:19:43 +00:00
stac
4e6b539086 debugpins: Add definitions for debug pins
Not yet used anywhere but will eventually allow
debug pins to be assigned during runtime init based
on configuration found in a new uavobject.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2741 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-02-06 01:03:06 +00:00
peabody124
ac031d9b0d OP-256 RC 3 is using TIM5 but wasn't previously handling this ISR. Passing to
the PWM ISR now.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2607 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-28 16:01:40 +00:00
sambas
d917ced2f6 Fix for pwm input reset problem? Try the line I commented out because I can't test this.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2606 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-28 13:30:12 +00:00
sambas
195b63b6bb OP-22 PIOS/Spektrum: Made spektrum input driver, NOT YET TESTED!!!, also preliminary support for CC, sync/supv timer not yet fixed.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2602 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-28 09:25:30 +00:00
peabody124
92dd78db51 OP-256 PIOS/PWM: Disable from the pios_board.c file when not using PWM
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2589 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-24 23:17:39 +00:00
peabody124
3b0be12b67 OP-291 PIOS/Servo: Fix a few interrupt mappins for OP
Also keep the priority of actuator at idle+4, dropping it down slipped through

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2580 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-24 07:52:20 +00:00
peabody124
7554021ed0 OP-256 PIOS/PWM: Set the interrupts correctly
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2577 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-24 07:52:11 +00:00
peabody124
99fcd089d4 OP-291 PIOS/Servo: Make the remapping of timers a part of the driver structure
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2569 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-24 07:51:48 +00:00
peabody124
da96ce15b9 OP-256 PIOS/PWM: Converting PWM input to use standard driver structure.
Beginning of unifying the input types into PIOS_RECEIVER.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2568 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-24 07:51:45 +00:00
peabody124
2d9f7f32d1 OP-291 PiOS/Servo: Converting output to use driver system
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2499 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-21 03:40:21 +00:00
peabody124
c2bdf624e8 OP-269 PIOS/ADC: Previous ADC driver update changed the PCLK2 divider for all
projects which messed up a timer on OP and serial on PipX.  Now this is only
changed for AHRS.  Ideally wouldn't even change for that but then ADC runs too
fast and we get a lot more CRC errors for dealing with all that data.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2459 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-16 23:00:48 +00:00
peabody124
0259b6d1f1 OP-269 PIOS/ADC: First part of conversion to driver structures
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2444 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-16 02:45:39 +00:00
peabody124
81b0c3fdb6 OP-269 PiOS/ADC: Moved AHRS ADC code to PiOS and made all the projects use it
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2440 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-16 02:45:22 +00:00
peabody124
ed11e64bb2 OP-251 Watchdog: Get rid of the old extra watchdog module and instead have
tasks directly update a flag for each module (which they register) and when all
flags set clear the watchdog then.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2365 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-10 00:16:30 +00:00
peabody124
e393000c34 OP-238 PIOS/SPI: Decrease pin clock rate from 50 to 10 Mhz. Since data at
1.125 MHz this should slow down the slew rates

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2361 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-09 20:49:46 +00:00
peabody124
85b7619617 OP-176 OP-238 Flight/IRQ and DMA: Increased the priority of the AHRS DMA
transfer, seems to reduce CRC errors

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2356 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-09 20:49:29 +00:00
peabody124
0f07d7f671 OP-240 OP-176 Flight: Setting the priority group back to 4 (anything higher
priority preempts) and adjusting the priorities around to be more sensible.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2355 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-09 20:49:26 +00:00
vassilis
407e660c97 Flight/TaskMonitor: Create TaskMonitor library, used to monitor the remaining task size of all running tasks.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2349 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-08 23:43:34 +00:00
peabody124
0e7661539e OP-238 AHRS Comms: Bring down clock rate of comms to AHRS to 2.25 MHz. Decrease
to only transmitting one object per transmission too to keep size down.
Also move to using the driver structure so the paramter is in a clear place.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2333 ebee16cc-31ac-478f-84a7-5cbb03baadba
2011-01-05 10:34:42 +00:00
kokomojoe
6499da40e3 OP-185 Flight Added init function for PIOS_IAP helper functions.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1892 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-10-06 02:07:11 +00:00
pip
73c8194acc Added PIOS_COM_TELEM_BAUDRATE, PIOS_COM_GPS_BAUDRATE, PIOS_COM_AUX_BAUDRATE & PIOS_COM_SPEKTRUM_BAUDRATE defines in pios_board.h with '#if defines' in pios_board.c for easier baudrate changing.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1644 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-15 17:18:38 +00:00
stac
95595664c3 telemetry: fix comments around #ifdef
No functional changes.

The closing comment on some of the USB_HID related
ifdefs was outdated.  Fixed.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1541 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-09-05 23:10:34 +00:00
peabody124
a084d21804 Merge branch 'watchdog'
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1281 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-13 05:18:17 +00:00
stac
f74c6ffdd5 i2c: rewrite i2c layer
The STM32 I2C block has a number of errata associated with it.
These errata are primarily related to timing sensitivities between
the peripheral and the interrupt handler.  In particular, the
correct generation of the stop bit relies on the I2C IRQ running
immediately and not being held off for any reason.

NOTE: The I2C interrupts must be the highest priority IRQs in the
      system to ensure correct operation.

I2C protocol is now implemented as a formal state machine.
See: stm32_i2c_fsm.{dot,jpg} for FSM description.

I2C init is now expressed by const initializers in pios_board.c
for both OP and AHRS boards.

I2C device drivers (ie. bmp085/hmc5843) now pass in const arrays
of an unlimited number of bus transfers to be done atomically.
The I2C adapter driver now handles all bus-level locking across the
list of transactions.  Generation of start/restart/stop conditions
are handled automatically over the list of transactions.

Timeouts have been removed from the API for now.  May be added
back later.

This driver has run error free on both the OP and AHRS boards for
up to 48hrs but it still sometimes fails earlier than that on the OP
board.  There is another possible set of improvements to the driver
that could employ the DMA engine for transfers of >= 2bytes.  This
change would reduce the timing sensitivities between the peripheral
and the driver but unfortunately, both the SPI and I2C interfaces
share the DMA1 engine.  That means only one of these two peripherals
can use the DMA engine and right now, SPI between OP and AHRS is
already using it.

Failures are currently fatal and will lock up the CPU.  This allows
useful information to be obtained in the failure cases.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1241 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-08 04:15:08 +00:00
sambas
7f6336d324 OP-22 Flight/PiOS: Spektrum reworked, input is mapped to old aux in receiver connector, works nicely with calibration plugin. Also bind works, just needs config flag to bind on powerup
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1189 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-08-01 10:34:07 +00:00
corvus
c8486d08e4 Fixed some bugs in OpenPilot Core.
- syntax error in pios_board_posix.c introduced with Doxygen comment blocks
- platform dependant code had been added to openpilot.c instead of pios_board.c
- redundant header inclusion (stm32... already included by PiOS)


git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1171 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-28 14:34:48 +00:00
dankers
32e6d53b23 Small comment issue that was causing build to fail
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1170 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-28 11:28:18 +00:00
edouard
9145a4b1a6 Doxygen work: created "OpenPilot System" group for system libraries and core files. Changed a typo on the Osd Doxygen. Let me know if you're OK with this approach.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1169 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-28 07:28:21 +00:00
peabody124
7d7802593e Oops, sorry missed these files
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1160 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-27 08:08:50 +00:00
corvus
fa57e42efa Deleted OpenPilot.posix branch. Integrated portability modifications into main tree
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1086 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-13 16:23:41 +00:00
stac
a3a2dbd634 spi: Add support for hardware CRC generation/checking
PIOS SPI devices may now make use of automatic CRC generation
and checking on block transfers.  Only supports CRC8 for now.

Since the SPI interface CRC calculation continues across message
boundaries (ie. not reset on every transfer), we must manually reset
the CRC registers for every transfer to allow the two sides of the
link to resynchronize.

Unfortunately, resetting the CRC registers requires disabling the
SPI peripheral which must now be done on every block transfer.

Note: The last byte of the tx buffer is never sent and is assumed to
      be a place holder for the tx CRC8.
Note: The last byte of the rx buffer is expected to hold the rx CRC8.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1011 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-04 02:21:42 +00:00
stac
0e6294ca27 spi: remove internal pull-up from input data lines
The input data lines between the OP and AHRS boards had internal
pull-ups enabled.  This seemed to be causing issues early on
during development of the inter-board comms.  Not sure if this
is still necessary but this is how the current code was tested.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1006 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-04 02:21:26 +00:00
stac
3eceef43d3 spi: Connect device specific DMA IRQ handlers
Mark the device specific DMA IRQ handlers as strongly linked
aliases for the genericly named interrupt vector symbol.

Here's how this works...
 * The address of the symbol DMA1_Channel2_IRQHandler is written
   into the DMA1/Channel2 interrupt vector by the linker script.
 * The startup_*.S file specifies Default_Handler() as a weakly
   linked alias for DMA1_Channel2_IRQHandler.
 * We now override the weakly linked alias with the strongly linked
   PIOS_SPI_sdcard_irq_handler().
 * This results in the address of PIOS_SPI_sdcard_irq_handler() being
   written to the vector table for the DMA1/Channel2 interrupt.
 * The PIOS_SPI_sdcard_irq_handler() function is now called whenever
   the DMA1/Channel2 interrupt fires.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@1003 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-07-04 02:21:13 +00:00
FredericG
e5c795e42b Remapped UART_AUX from PA9/10 (RX inputs) to PB6/7 (Servo output)
Rationale: (http://forums.openpilot.org/topic/800-rev-761-mkserial-adapt-to-com-usartx-pios-com-x/page__view__findpost__p__2203_)
  

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@836 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-06-20 17:48:59 +00:00
stac
771a56ca9d com/usart: generalize com driver API
- Created a pluggable COM layer
- Converted COM + USART init into static initializers
  rather than typedefs
- Generalized the USB HID COM API to match the USART
  API.
- Changed USART and COM layers to be data driven rather
  than #ifdef'ing/switching on the specifics of each port

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@760 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-06-13 04:24:26 +00:00
stac
8d015a57d0 pios spi: support both master and slave configs
Added support for SPI slave configurations to the pios SPI layer.

Converted the board specific configuration for the PIOS SPI layer to
use const static initializers rather than #defines (see pios_board.c).

SPI interface between the OP board and the AHRS is now operational at
a basic level, capable of moving simple single byte messages between
boards.  Multi-byte, CRC protected messages will be added on top of this.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@759 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-06-13 04:23:44 +00:00