/** ****************************************************************************** * @addtogroup Revolution Revolution configuration files * @{ * @brief Configures the revolution board * @{ * * @file pios_board.c * @author The OpenPilot Team, http://www.openpilot.org Copyright (C) 2011. * @brief Defines board specific static initializers for hardware for the Revolution board. * @see The GNU Public License (GPL) Version 3 * *****************************************************************************/ /* * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, but * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License * for more details. * * You should have received a copy of the GNU General Public License along * with this program; if not, write to the Free Software Foundation, Inc., * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include #if defined(PIOS_INCLUDE_SPI) #include #include #include #include #include "manualcontrolsettings.h" /* SPI1 Interface * - Used for BMA180 accelerometer */ void PIOS_SPI_accel_irq_handler(void); void DMA2_Stream0_IRQHandler(void) __attribute__((alias("PIOS_SPI_accel_irq_handler"))); void DMA2_Stream3_IRQHandler(void) __attribute__((alias("PIOS_SPI_accel_irq_handler"))); static const struct pios_spi_cfg pios_spi_accel_cfg = { .regs = SPI1, .remap = GPIO_AF_SPI1, .init = { .SPI_Mode = SPI_Mode_Master, .SPI_Direction = SPI_Direction_2Lines_FullDuplex, .SPI_DataSize = SPI_DataSize_8b, .SPI_NSS = SPI_NSS_Soft, .SPI_FirstBit = SPI_FirstBit_MSB, .SPI_CRCPolynomial = 7, .SPI_CPOL = SPI_CPOL_High, .SPI_CPHA = SPI_CPHA_2Edge, .SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_4, }, .use_crc = false, .dma = { .irq = { .flags = (DMA_IT_TCIF0 | DMA_IT_TEIF0 | DMA_IT_HTIF0), .init = { .NVIC_IRQChannel = DMA2_Stream0_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .rx = { .channel = DMA2_Stream0, .init = { .DMA_Channel = DMA_Channel_3, .DMA_PeripheralBaseAddr = (uint32_t)&(SPI1->DR), .DMA_DIR = DMA_DIR_PeripheralToMemory, .DMA_PeripheralInc = DMA_PeripheralInc_Disable, .DMA_MemoryInc = DMA_MemoryInc_Enable, .DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte, .DMA_MemoryDataSize = DMA_MemoryDataSize_Byte, .DMA_Mode = DMA_Mode_Normal, .DMA_Priority = DMA_Priority_Medium, .DMA_FIFOMode = DMA_FIFOMode_Disable, /* .DMA_FIFOThreshold */ .DMA_MemoryBurst = DMA_MemoryBurst_Single, .DMA_PeripheralBurst = DMA_PeripheralBurst_Single, }, }, .tx = { .channel = DMA2_Stream3, .init = { .DMA_Channel = DMA_Channel_3, .DMA_PeripheralBaseAddr = (uint32_t)&(SPI1->DR), .DMA_DIR = DMA_DIR_MemoryToPeripheral, .DMA_PeripheralInc = DMA_PeripheralInc_Disable, .DMA_MemoryInc = DMA_MemoryInc_Enable, .DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte, .DMA_MemoryDataSize = DMA_MemoryDataSize_Byte, .DMA_Mode = DMA_Mode_Normal, .DMA_Priority = DMA_Priority_High, .DMA_FIFOMode = DMA_FIFOMode_Disable, /* .DMA_FIFOThreshold */ .DMA_MemoryBurst = DMA_MemoryBurst_Single, .DMA_PeripheralBurst = DMA_PeripheralBurst_Single, }, }, }, .sclk = { .gpio = GPIOA, .init = { .GPIO_Pin = GPIO_Pin_5, .GPIO_Speed = GPIO_Speed_100MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, .miso = { .gpio = GPIOA, .init = { .GPIO_Pin = GPIO_Pin_6, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, .mosi = { .gpio = GPIOA, .init = { .GPIO_Pin = GPIO_Pin_7, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, .slave_count = 1, .ssel = { { .gpio = GPIOA, .init = { .GPIO_Pin = GPIO_Pin_4, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_Mode = GPIO_Mode_OUT, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, } }, }; static uint32_t pios_spi_accel_id; void PIOS_SPI_accel_irq_handler(void) { /* Call into the generic code to handle the IRQ for this specific device */ PIOS_SPI_IRQ_Handler(pios_spi_accel_id); } /* SPI2 Interface * - Used for gyro communications */ void PIOS_SPI_GYRO_irq_handler(void); void DMA1_Stream3_IRQHandler(void) __attribute__((alias("PIOS_SPI_gyro_irq_handler"))); void DMA1_Stream4_IRQHandler(void) __attribute__((alias("PIOS_SPI_gyro_irq_handler"))); static const struct pios_spi_cfg pios_spi_gyro_cfg = { .regs = SPI2, .remap = GPIO_AF_SPI2, .init = { .SPI_Mode = SPI_Mode_Master, .SPI_Direction = SPI_Direction_2Lines_FullDuplex, .SPI_DataSize = SPI_DataSize_8b, .SPI_NSS = SPI_NSS_Soft, .SPI_FirstBit = SPI_FirstBit_MSB, .SPI_CRCPolynomial = 7, .SPI_CPOL = SPI_CPOL_High, .SPI_CPHA = SPI_CPHA_2Edge, .SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_8, }, .use_crc = false, .dma = { .irq = { // Note this is the stream ID that triggers interrupts (in this case RX) .flags = (DMA_IT_TCIF3 | DMA_IT_TEIF3 | DMA_IT_HTIF3), .init = { .NVIC_IRQChannel = DMA1_Stream3_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .rx = { .channel = DMA1_Stream3, .init = { .DMA_Channel = DMA_Channel_0, .DMA_PeripheralBaseAddr = (uint32_t) & (SPI2->DR), .DMA_DIR = DMA_DIR_PeripheralToMemory, .DMA_PeripheralInc = DMA_PeripheralInc_Disable, .DMA_MemoryInc = DMA_MemoryInc_Enable, .DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte, .DMA_MemoryDataSize = DMA_MemoryDataSize_Byte, .DMA_Mode = DMA_Mode_Normal, .DMA_Priority = DMA_Priority_Medium, //TODO: Enable FIFO .DMA_FIFOMode = DMA_FIFOMode_Disable, .DMA_FIFOThreshold = DMA_FIFOThreshold_Full, .DMA_MemoryBurst = DMA_MemoryBurst_Single, .DMA_PeripheralBurst = DMA_PeripheralBurst_Single, }, }, .tx = { .channel = DMA1_Stream4, .init = { .DMA_Channel = DMA_Channel_0, .DMA_PeripheralBaseAddr = (uint32_t) & (SPI2->DR), .DMA_DIR = DMA_DIR_MemoryToPeripheral, .DMA_PeripheralInc = DMA_PeripheralInc_Disable, .DMA_MemoryInc = DMA_MemoryInc_Enable, .DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte, .DMA_MemoryDataSize = DMA_MemoryDataSize_Byte, .DMA_Mode = DMA_Mode_Normal, .DMA_Priority = DMA_Priority_Medium, .DMA_FIFOMode = DMA_FIFOMode_Disable, .DMA_FIFOThreshold = DMA_FIFOThreshold_Full, .DMA_MemoryBurst = DMA_MemoryBurst_Single, .DMA_PeripheralBurst = DMA_PeripheralBurst_Single, }, }, }, .sclk = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_13, .GPIO_Speed = GPIO_Speed_100MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_NOPULL }, }, .miso = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_14, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_NOPULL }, }, .mosi = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_15, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_NOPULL }, }, .slave_count = 1, .ssel = { { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_12, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_Mode = GPIO_Mode_OUT, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, } }, }; uint32_t pios_spi_gyro_id; void PIOS_SPI_gyro_irq_handler(void) { /* Call into the generic code to handle the IRQ for this specific device */ PIOS_SPI_IRQ_Handler(pios_spi_gyro_id); } /* SPI3 Interface * - Used for flash communications */ void PIOS_SPI_flash_irq_handler(void); void DMA1_Stream0_IRQHandler(void) __attribute__((alias("PIOS_SPI_flash_irq_handler"))); void DMA1_Stream2_IRQHandler(void) __attribute__((alias("PIOS_SPI_flash_irq_handler"))); static const struct pios_spi_cfg pios_spi_flash_cfg = { .regs = SPI3, .remap = GPIO_AF_SPI3, .init = { .SPI_Mode = SPI_Mode_Master, .SPI_Direction = SPI_Direction_2Lines_FullDuplex, .SPI_DataSize = SPI_DataSize_8b, .SPI_NSS = SPI_NSS_Soft, .SPI_FirstBit = SPI_FirstBit_MSB, .SPI_CRCPolynomial = 7, .SPI_CPOL = SPI_CPOL_High, .SPI_CPHA = SPI_CPHA_2Edge, .SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_2, }, .use_crc = false, .dma = { .irq = { // Note this is the stream ID that triggers interrupts (in this case RX) .flags = (DMA_IT_TCIF3 | DMA_IT_TEIF3 | DMA_IT_HTIF3), .init = { .NVIC_IRQChannel = DMA1_Stream0_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .rx = { .channel = DMA1_Stream0, .init = { .DMA_Channel = DMA_Channel_0, .DMA_PeripheralBaseAddr = (uint32_t) & (SPI3->DR), .DMA_DIR = DMA_DIR_PeripheralToMemory, .DMA_PeripheralInc = DMA_PeripheralInc_Disable, .DMA_MemoryInc = DMA_MemoryInc_Enable, .DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte, .DMA_MemoryDataSize = DMA_MemoryDataSize_Byte, .DMA_Mode = DMA_Mode_Normal, .DMA_Priority = DMA_Priority_Medium, //TODO: Enable FIFO .DMA_FIFOMode = DMA_FIFOMode_Disable, .DMA_FIFOThreshold = DMA_FIFOThreshold_Full, .DMA_MemoryBurst = DMA_MemoryBurst_Single, .DMA_PeripheralBurst = DMA_PeripheralBurst_Single, }, }, .tx = { .channel = DMA1_Stream2, .init = { .DMA_Channel = DMA_Channel_0, .DMA_PeripheralBaseAddr = (uint32_t) & (SPI3->DR), .DMA_DIR = DMA_DIR_MemoryToPeripheral, .DMA_PeripheralInc = DMA_PeripheralInc_Disable, .DMA_MemoryInc = DMA_MemoryInc_Enable, .DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte, .DMA_MemoryDataSize = DMA_MemoryDataSize_Byte, .DMA_Mode = DMA_Mode_Normal, .DMA_Priority = DMA_Priority_Medium, .DMA_FIFOMode = DMA_FIFOMode_Disable, .DMA_FIFOThreshold = DMA_FIFOThreshold_Full, .DMA_MemoryBurst = DMA_MemoryBurst_Single, .DMA_PeripheralBurst = DMA_PeripheralBurst_Single, }, }, }, .sclk = { .gpio = GPIOC, .init = { .GPIO_Pin = GPIO_Pin_10, .GPIO_Speed = GPIO_Speed_100MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_NOPULL }, }, .miso = { .gpio = GPIOC, .init = { .GPIO_Pin = GPIO_Pin_11, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_NOPULL }, }, .mosi = { .gpio = GPIOC, .init = { .GPIO_Pin = GPIO_Pin_12, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_NOPULL }, }, .slave_count = 1, .ssel = { { .gpio = GPIOD, .init = { .GPIO_Pin = GPIO_Pin_2, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_Mode = GPIO_Mode_OUT, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, } }, }; uint32_t pios_spi_flash_id; void PIOS_SPI_flash_irq_handler(void) { /* Call into the generic code to handle the IRQ for this specific device */ PIOS_SPI_IRQ_Handler(pios_spi_flash_id); } #endif /* PIOS_INCLUDE_SPI */ #include #if defined(PIOS_INCLUDE_GPS) /* * GPS USART */ static const struct pios_usart_cfg pios_usart_gps_cfg = { .regs = USART1, .remap = GPIO_AF_USART1, .init = { .USART_BaudRate = 57600, .USART_WordLength = USART_WordLength_8b, .USART_Parity = USART_Parity_No, .USART_StopBits = USART_StopBits_1, .USART_HardwareFlowControl = USART_HardwareFlowControl_None, .USART_Mode = USART_Mode_Rx | USART_Mode_Tx, }, .irq = { .init = { .NVIC_IRQChannel = USART1_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .rx = { .gpio = GPIOA, .init = { .GPIO_Pin = GPIO_Pin_10, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, .tx = { .gpio = GPIOA, .init = { .GPIO_Pin = GPIO_Pin_9, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, }; #define PIOS_COM_GPS_RX_BUF_LEN 192 #endif /* PIOS_INCLUDE_GPS */ #ifdef PIOS_INCLUDE_COM_AUX /* * AUX USART */ static const struct pios_usart_cfg pios_usart_aux_cfg = { .regs = USART6, .remap = GPIO_AF_USART6, .init = { .USART_BaudRate = 230400, .USART_WordLength = USART_WordLength_8b, .USART_Parity = USART_Parity_No, .USART_StopBits = USART_StopBits_1, .USART_HardwareFlowControl = USART_HardwareFlowControl_None, .USART_Mode = USART_Mode_Rx | USART_Mode_Tx, }, .irq = { .init = { .NVIC_IRQChannel = USART6_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .rx = { .gpio = GPIOC, .init = { .GPIO_Pin = GPIO_Pin_7, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, .tx = { .gpio = GPIOC, .init = { .GPIO_Pin = GPIO_Pin_6, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, }; #endif /* PIOS_COM_AUX */ #ifdef PIOS_INCLUDE_COM_TELEM /* * Telemetry on main USART */ static const struct pios_usart_cfg pios_usart_telem_main_cfg = { .regs = USART6, .remap = GPIO_AF_USART6, .init = { .USART_BaudRate = 57600, .USART_WordLength = USART_WordLength_8b, .USART_Parity = USART_Parity_No, .USART_StopBits = USART_StopBits_1, .USART_HardwareFlowControl = USART_HardwareFlowControl_None, .USART_Mode = USART_Mode_Rx | USART_Mode_Tx, }, .irq = { .init = { .NVIC_IRQChannel = USART6_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .rx = { .gpio = GPIOC, .init = { .GPIO_Pin = GPIO_Pin_7, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, .tx = { .gpio = GPIOC, .init = { .GPIO_Pin = GPIO_Pin_6, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, }; #define PIOS_COM_TELEM_RF_RX_BUF_LEN 512 #define PIOS_COM_TELEM_RF_TX_BUF_LEN 512 #endif /* PIOS_COM_TELEM */ #if defined(PIOS_INCLUDE_DSM) /* * Spektrum/JR DSM USART */ #include static const struct pios_usart_cfg pios_usart_dsm_main_cfg = { .regs = USART3, .remap = GPIO_AF_USART3, .init = { .USART_BaudRate = 115200, .USART_WordLength = USART_WordLength_8b, .USART_Parity = USART_Parity_No, .USART_StopBits = USART_StopBits_1, .USART_HardwareFlowControl = USART_HardwareFlowControl_None, .USART_Mode = USART_Mode_Rx, }, .irq = { .init = { .NVIC_IRQChannel = USART3_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .rx = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_11, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, .tx = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_10, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, }; static const struct pios_dsm_cfg pios_dsm_main_cfg = { .bind = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_11, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_OUT, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_NOPULL }, }, }; static const struct pios_usart_cfg pios_usart_dsm_flexi_cfg = { .regs = USART3, .remap = GPIO_AF_USART3, .init = { .USART_BaudRate = 115200, .USART_WordLength = USART_WordLength_8b, .USART_Parity = USART_Parity_No, .USART_StopBits = USART_StopBits_1, .USART_HardwareFlowControl = USART_HardwareFlowControl_None, .USART_Mode = USART_Mode_Rx, }, .irq = { .init = { .NVIC_IRQChannel = USART3_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .rx = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_11, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, .tx = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_10, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, }, }; static const struct pios_dsm_cfg pios_dsm_flexi_cfg = { .bind = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_11, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_OUT, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_NOPULL }, }, }; #endif /* PIOS_INCLUDE_DSM */ #if defined(PIOS_INCLUDE_COM) #include #endif /* PIOS_INCLUDE_COM */ #if defined(PIOS_INCLUDE_I2C) #include /* * I2C Adapters */ void PIOS_I2C_mag_adapter_ev_irq_handler(void); void PIOS_I2C_mag_adapter_er_irq_handler(void); void I2C1_EV_IRQHandler() __attribute__ ((alias("PIOS_I2C_mag_adapter_ev_irq_handler"))); void I2C1_ER_IRQHandler() __attribute__ ((alias("PIOS_I2C_mag_adapter_er_irq_handler"))); static const struct pios_i2c_adapter_cfg pios_i2c_mag_adapter_cfg = { .regs = I2C1, .remap = GPIO_AF_I2C1, .init = { .I2C_Mode = I2C_Mode_I2C, .I2C_OwnAddress1 = 0, .I2C_Ack = I2C_Ack_Enable, .I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit, .I2C_DutyCycle = I2C_DutyCycle_2, .I2C_ClockSpeed = 400000, /* bits/s */ }, .transfer_timeout_ms = 50, .scl = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_6, .GPIO_Mode = GPIO_Mode_AF, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_OType = GPIO_OType_OD, .GPIO_PuPd = GPIO_PuPd_NOPULL, }, }, .sda = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_7, .GPIO_Mode = GPIO_Mode_AF, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_OType = GPIO_OType_OD, .GPIO_PuPd = GPIO_PuPd_NOPULL, }, }, .event = { .flags = 0, /* FIXME: check this */ .init = { .NVIC_IRQChannel = I2C1_EV_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .error = { .flags = 0, /* FIXME: check this */ .init = { .NVIC_IRQChannel = I2C1_ER_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; uint32_t pios_i2c_mag_adapter_id; void PIOS_I2C_mag_adapter_ev_irq_handler(void) { /* Call into the generic code to handle the IRQ for this specific device */ PIOS_I2C_EV_IRQ_Handler(pios_i2c_mag_adapter_id); } void PIOS_I2C_mag_adapter_er_irq_handler(void) { /* Call into the generic code to handle the IRQ for this specific device */ PIOS_I2C_ER_IRQ_Handler(pios_i2c_mag_adapter_id); } void PIOS_I2C_flexiport_adapter_ev_irq_handler(void); void PIOS_I2C_flexiport_adapter_er_irq_handler(void); void I2C2_EV_IRQHandler() __attribute__ ((alias ("PIOS_I2C_flexiport_adapter_ev_irq_handler"))); void I2C2_ER_IRQHandler() __attribute__ ((alias ("PIOS_I2C_flexiport_adapter_er_irq_handler"))); static const struct pios_i2c_adapter_cfg pios_i2c_flexiport_adapter_cfg = { .regs = I2C2, .remap = GPIO_AF_I2C2, .init = { .I2C_Mode = I2C_Mode_I2C, .I2C_OwnAddress1 = 0, .I2C_Ack = I2C_Ack_Enable, .I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit, .I2C_DutyCycle = I2C_DutyCycle_2, .I2C_ClockSpeed = 400000, /* bits/s */ }, .transfer_timeout_ms = 50, .scl = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_10, .GPIO_Mode = GPIO_Mode_AF, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_OType = GPIO_OType_OD, .GPIO_PuPd = GPIO_PuPd_NOPULL, }, }, .sda = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_11, .GPIO_Mode = GPIO_Mode_AF, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_OType = GPIO_OType_OD, .GPIO_PuPd = GPIO_PuPd_NOPULL, }, }, .event = { .flags = 0, /* FIXME: check this */ .init = { .NVIC_IRQChannel = I2C2_EV_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .error = { .flags = 0, /* FIXME: check this */ .init = { .NVIC_IRQChannel = I2C2_ER_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; uint32_t pios_i2c_flexiport_adapter_id; void PIOS_I2C_flexiport_adapter_ev_irq_handler(void) { /* Call into the generic code to handle the IRQ for this specific device */ PIOS_I2C_EV_IRQ_Handler(pios_i2c_flexiport_adapter_id); } void PIOS_I2C_flexiport_adapter_er_irq_handler(void) { /* Call into the generic code to handle the IRQ for this specific device */ PIOS_I2C_ER_IRQ_Handler(pios_i2c_flexiport_adapter_id); } void PIOS_I2C_pressure_adapter_ev_irq_handler(void); void PIOS_I2C_pressure_adapter_er_irq_handler(void); void I2C3_EV_IRQHandler() __attribute__ ((alias ("PIOS_I2C_pressure_adapter_ev_irq_handler"))); void I2C3_ER_IRQHandler() __attribute__ ((alias ("PIOS_I2C_pressure_adapter_er_irq_handler"))); static const struct pios_i2c_adapter_cfg pios_i2c_pressure_adapter_cfg = { .regs = I2C3, .remap = GPIO_AF_I2C3, .init = { .I2C_Mode = I2C_Mode_I2C, .I2C_OwnAddress1 = 0, .I2C_Ack = I2C_Ack_Enable, .I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit, .I2C_DutyCycle = I2C_DutyCycle_2, .I2C_ClockSpeed = 40000, /* bits/s */ }, .transfer_timeout_ms = 50, .scl = { .gpio = GPIOA, .init = { .GPIO_Pin = GPIO_Pin_8, .GPIO_Mode = GPIO_Mode_AF, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_OType = GPIO_OType_OD, .GPIO_PuPd = GPIO_PuPd_NOPULL, }, }, .sda = { .gpio = GPIOC, .init = { .GPIO_Pin = GPIO_Pin_9, .GPIO_Mode = GPIO_Mode_AF, .GPIO_Speed = GPIO_Speed_50MHz, .GPIO_OType = GPIO_OType_OD, .GPIO_PuPd = GPIO_PuPd_NOPULL, }, }, .event = { .flags = 0, /* FIXME: check this */ .init = { .NVIC_IRQChannel = I2C3_EV_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .error = { .flags = 0, /* FIXME: check this */ .init = { .NVIC_IRQChannel = I2C3_ER_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; uint32_t pios_i2c_pressure_adapter_id; void PIOS_I2C_pressure_adapter_ev_irq_handler(void) { /* Call into the generic code to handle the IRQ for this specific device */ PIOS_I2C_EV_IRQ_Handler(pios_i2c_pressure_adapter_id); } void PIOS_I2C_pressure_adapter_er_irq_handler(void) { /* Call into the generic code to handle the IRQ for this specific device */ PIOS_I2C_ER_IRQ_Handler(pios_i2c_pressure_adapter_id); } #endif /* PIOS_INCLUDE_I2C */ #if defined(PIOS_INCLUDE_RTC) /* * Realtime Clock (RTC) */ #include void PIOS_RTC_IRQ_Handler (void); void RTC_WKUP_IRQHandler() __attribute__ ((alias ("PIOS_RTC_IRQ_Handler"))); static const struct pios_rtc_cfg pios_rtc_main_cfg = { .clksrc = RCC_RTCCLKSource_HSE_Div16, // Divide 8 Mhz crystal down to 1 // For some reason it's acting like crystal is 16 Mhz. This clock is then divided // by another 16 to give a nominal 62.5 khz clock .prescaler = 100, // Every 100 cycles gives 625 Hz .irq = { .init = { .NVIC_IRQChannel = RTC_WKUP_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; void PIOS_RTC_IRQ_Handler (void) { PIOS_RTC_irq_handler (); } #endif #include "pios_tim_priv.h" static const TIM_TimeBaseInitTypeDef tim_3_5_9_10_11_time_base = { .TIM_Prescaler = (PIOS_MASTER_CLOCK / 1000000) - 1, .TIM_ClockDivision = TIM_CKD_DIV1, .TIM_CounterMode = TIM_CounterMode_Up, .TIM_Period = ((1000000 / PIOS_SERVO_UPDATE_HZ) - 1), .TIM_RepetitionCounter = 0x0000, }; static const struct pios_tim_clock_cfg tim_3_cfg = { .timer = TIM3, .time_base_init = &tim_3_5_9_10_11_time_base, .irq = { .init = { .NVIC_IRQChannel = TIM3_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; static const struct pios_tim_clock_cfg tim_5_cfg = { .timer = TIM5, .time_base_init = &tim_3_5_9_10_11_time_base, .irq = { .init = { .NVIC_IRQChannel = TIM5_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; static const struct pios_tim_clock_cfg tim_9_cfg = { .timer = TIM9, .time_base_init = &tim_3_5_9_10_11_time_base, .irq = { .init = { .NVIC_IRQChannel = TIM1_BRK_TIM9_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; static const struct pios_tim_clock_cfg tim_10_cfg = { .timer = TIM10, .time_base_init = &tim_3_5_9_10_11_time_base, .irq = { .init = { .NVIC_IRQChannel = TIM1_UP_TIM10_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; static const struct pios_tim_clock_cfg tim_11_cfg = { .timer = TIM11, .time_base_init = &tim_3_5_9_10_11_time_base, .irq = { .init = { .NVIC_IRQChannel = TIM1_TRG_COM_TIM11_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; // Set up timers that only have inputs static const TIM_TimeBaseInitTypeDef tim_1_4_time_base = { .TIM_Prescaler = (PIOS_MASTER_CLOCK / 1000000) - 1, .TIM_ClockDivision = TIM_CKD_DIV1, .TIM_CounterMode = TIM_CounterMode_Up, .TIM_Period = 0xFFFF, .TIM_RepetitionCounter = 0x0000, }; static const struct pios_tim_clock_cfg tim_1_cfg = { .timer = TIM1, .time_base_init = &tim_1_4_time_base, .irq = { .init = { .NVIC_IRQChannel = TIM1_CC_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; static const struct pios_tim_clock_cfg tim_4_cfg = { .timer = TIM4, .time_base_init = &tim_1_4_time_base, .irq = { .init = { .NVIC_IRQChannel = TIM4_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; /** * Pios servo configuration structures */ #include static const struct pios_tim_channel pios_tim_servoport_all_pins[] = { { .timer = TIM9, .timer_chan = TIM_Channel_1, .pin = { .gpio = GPIOE, .init = { .GPIO_Pin = GPIO_Pin_5, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource5, }, .remap = GPIO_AF_TIM9, }, { .timer = TIM9, .timer_chan = TIM_Channel_2, .pin = { .gpio = GPIOE, .init = { .GPIO_Pin = GPIO_Pin_6, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource6, }, .remap = GPIO_AF_TIM9, }, { .timer = TIM10, .timer_chan = TIM_Channel_1, .pin = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_8, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource8, }, .remap = GPIO_AF_TIM10, }, { .timer = TIM11, .timer_chan = TIM_Channel_1, .pin = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_9, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource9, }, .remap = GPIO_AF_TIM11, }, { .timer = TIM5, .timer_chan = TIM_Channel_3, .pin = { .gpio = GPIOA, .init = { .GPIO_Pin = GPIO_Pin_2, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource2, }, .remap = GPIO_AF_TIM5, }, { .timer = TIM5, .timer_chan = TIM_Channel_4, .pin = { .gpio = GPIOA, .init = { .GPIO_Pin = GPIO_Pin_3, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource3, }, .remap = GPIO_AF_TIM5, }, { .timer = TIM3, .timer_chan = TIM_Channel_3, .pin = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_0, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource0, }, .remap = GPIO_AF_TIM3, }, { .timer = TIM3, .timer_chan = TIM_Channel_3, .pin = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_1, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource1, }, .remap = GPIO_AF_TIM3, }, }; const struct pios_servo_cfg pios_servo_cfg = { .tim_oc_init = { .TIM_OCMode = TIM_OCMode_PWM1, .TIM_OutputState = TIM_OutputState_Enable, .TIM_OutputNState = TIM_OutputNState_Disable, .TIM_Pulse = PIOS_SERVOS_INITIAL_POSITION, .TIM_OCPolarity = TIM_OCPolarity_High, .TIM_OCNPolarity = TIM_OCPolarity_High, .TIM_OCIdleState = TIM_OCIdleState_Reset, .TIM_OCNIdleState = TIM_OCNIdleState_Reset, }, .channels = pios_tim_servoport_all_pins, .num_channels = NELEMENTS(pios_tim_servoport_all_pins), }; /* * PWM Inputs */ #if defined(PIOS_INCLUDE_PWM) || defined(PIOS_INCLUDE_PPM) #include static const struct pios_tim_channel pios_tim_rcvrport_all_channels[] = { { .timer = TIM4, .timer_chan = TIM_Channel_4, .pin = { .gpio = GPIOD, .init = { .GPIO_Pin = GPIO_Pin_15, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource15, }, .remap = GPIO_AF_TIM4, }, { .timer = TIM4, .timer_chan = TIM_Channel_3, .pin = { .gpio = GPIOD, .init = { .GPIO_Pin = GPIO_Pin_14, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource14, }, .remap = GPIO_AF_TIM4, }, { .timer = TIM4, .timer_chan = TIM_Channel_2, .pin = { .gpio = GPIOD, .init = { .GPIO_Pin = GPIO_Pin_13, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource13, }, .remap = GPIO_AF_TIM4, }, { .timer = TIM4, .timer_chan = TIM_Channel_1, .pin = { .gpio = GPIOD, .init = { .GPIO_Pin = GPIO_Pin_12, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource12, }, .remap = GPIO_AF_TIM4, }, { .timer = TIM1, .timer_chan = TIM_Channel_4, .pin = { .gpio = GPIOE, .init = { .GPIO_Pin = GPIO_Pin_14, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource14, }, .remap = GPIO_AF_TIM1, }, { .timer = TIM1, .timer_chan = TIM_Channel_3, .pin = { .gpio = GPIOE, .init = { .GPIO_Pin = GPIO_Pin_13, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource13, }, .remap = GPIO_AF_TIM1, }, { .timer = TIM1, .timer_chan = TIM_Channel_2, .pin = { .gpio = GPIOE, .init = { .GPIO_Pin = GPIO_Pin_11, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource11, }, .remap = GPIO_AF_TIM1, }, { .timer = TIM1, .timer_chan = TIM_Channel_1, .pin = { .gpio = GPIOE, .init = { .GPIO_Pin = GPIO_Pin_9, .GPIO_Speed = GPIO_Speed_2MHz, .GPIO_Mode = GPIO_Mode_AF, .GPIO_OType = GPIO_OType_PP, .GPIO_PuPd = GPIO_PuPd_UP }, .pin_source = GPIO_PinSource1, }, .remap = GPIO_AF_TIM1, }, }; const struct pios_pwm_cfg pios_pwm_cfg = { .tim_ic_init = { .TIM_ICPolarity = TIM_ICPolarity_Rising, .TIM_ICSelection = TIM_ICSelection_DirectTI, .TIM_ICPrescaler = TIM_ICPSC_DIV1, .TIM_ICFilter = 0x0, }, .channels = pios_tim_rcvrport_all_channels, .num_channels = NELEMENTS(pios_tim_rcvrport_all_channels), }; #endif /* * PPM Input */ #if defined(PIOS_INCLUDE_PPM) #include static const struct pios_ppm_cfg pios_ppm_cfg = { .tim_ic_init = { .TIM_ICPolarity = TIM_ICPolarity_Rising, .TIM_ICSelection = TIM_ICSelection_DirectTI, .TIM_ICPrescaler = TIM_ICPSC_DIV1, .TIM_ICFilter = 0x0, .TIM_Channel = TIM_Channel_2, }, /* Use only the first channel for ppm */ .channels = &pios_tim_rcvrport_all_channels[0], .num_channels = 1, }; #endif //PPM #if defined(PIOS_INCLUDE_RCVR) #include "pios_rcvr_priv.h" /* One slot per selectable receiver group. * eg. PWM, PPM, GCS, SPEKTRUM1, SPEKTRUM2, SBUS * NOTE: No slot in this map for NONE. */ uint32_t pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_NONE]; #endif extern const struct pios_com_driver pios_usart_com_driver; uint32_t pios_com_aux_id; uint32_t pios_com_gps_id; uint32_t pios_com_telem_usb_id; uint32_t pios_com_telem_rf_id; /** * Sensor configurations */ #include "pios_hmc5883.h" static const struct pios_hmc5883_cfg pios_hmc5883_cfg = { .drdy = { .gpio = GPIOB, .init = { .GPIO_Pin = GPIO_Pin_5, .GPIO_Speed = GPIO_Speed_100MHz, .GPIO_Mode = GPIO_Mode_IN, .GPIO_OType = GPIO_OType_OD, .GPIO_PuPd = GPIO_PuPd_NOPULL, }, }, .eoc_exti = { .pin_source = EXTI_PinSource5, .port_source = EXTI_PortSourceGPIOB, .init = { .EXTI_Line = EXTI_Line5, // matches above GPIO pin .EXTI_Mode = EXTI_Mode_Interrupt, .EXTI_Trigger = EXTI_Trigger_Rising, .EXTI_LineCmd = ENABLE, }, }, .eoc_irq = { .init = { .NVIC_IRQChannel = EXTI9_5_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_LOW, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .M_ODR = PIOS_HMC5883_ODR_75, .Meas_Conf = PIOS_HMC5883_MEASCONF_NORMAL, .Gain = PIOS_HMC5883_GAIN_1_9, .Mode = PIOS_HMC5883_MODE_CONTINUOUS, }; #include "pios_ms5611.h" static const struct pios_ms5611_cfg pios_ms5611_cfg = { .oversampling = 1, }; #include "pios_bma180.h" static const struct pios_bma180_cfg pios_bma180_cfg = { .drdy = { .gpio = GPIOC, .init = { .GPIO_Pin = GPIO_Pin_4, .GPIO_Speed = GPIO_Speed_100MHz, .GPIO_Mode = GPIO_Mode_IN, .GPIO_OType = GPIO_OType_OD, .GPIO_PuPd = GPIO_PuPd_NOPULL, }, }, .eoc_exti = { .pin_source = EXTI_PinSource4, .port_source = EXTI_PortSourceGPIOC, .init = { .EXTI_Line = EXTI_Line4, // matches above GPIO pin .EXTI_Mode = EXTI_Mode_Interrupt, .EXTI_Trigger = EXTI_Trigger_Rising, .EXTI_LineCmd = ENABLE, }, }, .eoc_irq = { .init = { .NVIC_IRQChannel = EXTI4_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_LOW, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, }; #include "pios_mpu6000.h" static const struct pios_mpu6000_cfg pios_mpu6000_cfg = { .drdy = { .gpio = GPIOD, .init = { .GPIO_Pin = GPIO_Pin_8, .GPIO_Speed = GPIO_Speed_100MHz, .GPIO_Mode = GPIO_Mode_IN, .GPIO_OType = GPIO_OType_OD, .GPIO_PuPd = GPIO_PuPd_NOPULL, }, }, .eoc_exti = { .pin_source = EXTI_PinSource8, .port_source = EXTI_PortSourceGPIOD, .init = { .EXTI_Line = EXTI_Line8, // matches above GPIO pin .EXTI_Mode = EXTI_Mode_Interrupt, .EXTI_Trigger = EXTI_Trigger_Rising, .EXTI_LineCmd = ENABLE, }, }, .eoc_irq = { .init = { .NVIC_IRQChannel = EXTI9_5_IRQn, .NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH, .NVIC_IRQChannelSubPriority = 0, .NVIC_IRQChannelCmd = ENABLE, }, }, .Fifo_store = PIOS_MPU6000_FIFO_TEMP_OUT | PIOS_MPU6000_FIFO_GYRO_X_OUT | PIOS_MPU6000_FIFO_GYRO_Y_OUT | PIOS_MPU6000_FIFO_GYRO_Z_OUT, // Clock at 8 khz, downsampled by 8 for 1khz .Smpl_rate_div = 7, .interrupt_cfg = PIOS_MPU6000_INT_CLR_ANYRD, .interrupt_en = PIOS_MPU6000_INTEN_DATA_RDY, .User_ctl = PIOS_MPU6000_USERCTL_FIFO_EN, .Pwr_mgmt_clk = PIOS_MPU6000_PWRMGMT_PLL_X_CLK, .gyro_range = PIOS_MPU6000_SCALE_500_DEG, .filter = PIOS_MPU6000_LOWPASS_256_HZ }; /** * PIOS_Board_Init() * initializes all the core subsystems on this specific hardware * called from System/openpilot.c */ void PIOS_Board_Init(void) { /* Delay system */ PIOS_DELAY_Init(); #ifdef PIOS_DEBUG_ENABLE_DEBUG_PINS PIOS_DEBUG_Init(&pios_tim_servo_all_channels, NELEMENTS(pios_tim_servo_all_channels)); #endif /* PIOS_DEBUG_ENABLE_DEBUG_PINS */ /* Set up the SPI interface to the flash */ if (PIOS_SPI_Init(&pios_spi_flash_id, &pios_spi_flash_cfg)) { PIOS_DEBUG_Assert(0); } PIOS_Flash_W25X_Init(pios_spi_flash_id); PIOS_FLASHFS_Init(); /* Initialize UAVObject libraries */ EventDispatcherInitialize(); UAVObjInitialize(); HwSettingsInitialize(); #if defined(PIOS_INCLUDE_RTC) PIOS_RTC_Init(&pios_rtc_main_cfg); #endif /* Initialize the alarms library */ AlarmsInitialize(); /* Initialize the task monitor library */ TaskMonitorInitialize(); /* Set up pulse timers */ PIOS_TIM_InitClock(&tim_1_cfg); PIOS_TIM_InitClock(&tim_3_cfg); PIOS_TIM_InitClock(&tim_4_cfg); PIOS_TIM_InitClock(&tim_4_cfg); PIOS_TIM_InitClock(&tim_5_cfg); PIOS_TIM_InitClock(&tim_9_cfg); PIOS_TIM_InitClock(&tim_10_cfg); PIOS_TIM_InitClock(&tim_11_cfg); /* IAP System Setup */ //PIOS_IAP_Init(); #if defined(PIOS_INCLUDE_COM) #if defined(PIOS_INCLUDE_GPS) uint32_t pios_usart_gps_id; if (PIOS_USART_Init(&pios_usart_gps_id, &pios_usart_telem_main_cfg)) { PIOS_Assert(0); } uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_GPS_RX_BUF_LEN); PIOS_Assert(rx_buffer); if (PIOS_COM_Init(&pios_com_gps_id, &pios_usart_com_driver, pios_usart_gps_id, rx_buffer, PIOS_COM_GPS_RX_BUF_LEN, NULL, 0)) { PIOS_Assert(0); } #endif /* PIOS_INCLUDE_GPS */ #if defined(PIOS_INCLUDE_COM_AUX) { uint32_t pios_usart_aux_id; if (PIOS_USART_Init(&pios_usart_aux_id, &pios_usart_aux_cfg)) { PIOS_DEBUG_Assert(0); } const uint32_t BUF_SIZE = 512; uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(BUF_SIZE); uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(BUF_SIZE); PIOS_Assert(rx_buffer); PIOS_Assert(tx_buffer); if (PIOS_COM_Init(&pios_com_aux_id, &pios_usart_com_driver, pios_usart_aux_id, rx_buffer, BUF_SIZE, tx_buffer, BUF_SIZE)) { PIOS_DEBUG_Assert(0); } } #else pios_com_aux_id = 0; #endif /* PIOS_INCLUDE_COM_AUX */ #if defined(PIOS_INCLUDE_COM_TELEM) { /* Eventually add switch for this port function */ uint32_t pios_usart_telem_rf_id; if (PIOS_USART_Init(&pios_usart_telem_rf_id, &pios_usart_gps_cfg)) { PIOS_Assert(0); } uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_RF_RX_BUF_LEN); uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_RF_TX_BUF_LEN); PIOS_Assert(rx_buffer); PIOS_Assert(tx_buffer); if (PIOS_COM_Init(&pios_com_telem_rf_id, &pios_usart_com_driver, pios_usart_telem_rf_id, rx_buffer, PIOS_COM_TELEM_RF_RX_BUF_LEN, tx_buffer, PIOS_COM_TELEM_RF_TX_BUF_LEN)) { PIOS_Assert(0); } } #else pios_com_telem_rf_id = 0; #endif /* PIOS_INCLUDE_COM_TELEM */ #endif /* PIOS_INCLUDE_COM */ // Set up spektrum receiver enum pios_dsm_proto proto; proto = PIOS_DSM_PROTO_DSM2; uint32_t pios_usart_dsm_id; if (PIOS_USART_Init(&pios_usart_dsm_id, &pios_usart_dsm_main_cfg)) { PIOS_Assert(0); } uint32_t pios_dsm_id; if (PIOS_DSM_Init(&pios_dsm_id, &pios_dsm_main_cfg, &pios_usart_com_driver, pios_usart_dsm_id, proto, 0)) { PIOS_Assert(0); } uint32_t pios_dsm_rcvr_id; if (PIOS_RCVR_Init(&pios_dsm_rcvr_id, &pios_dsm_rcvr_driver, pios_dsm_id)) { PIOS_Assert(0); } pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_DSMMAINPORT] = pios_dsm_rcvr_id; #if defined(PIOS_INCLUDE_PWM) && defined(PIOS_INCLUDE_RCVR) /* Set up the receiver port. Later this should be optional */ uint32_t pios_pwm_id; PIOS_PWM_Init(&pios_pwm_id, &pios_pwm_cfg); uint32_t pios_pwm_rcvr_id; if (PIOS_RCVR_Init(&pios_pwm_rcvr_id, &pios_pwm_rcvr_driver, pios_pwm_id)) { PIOS_Assert(0); } pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PWM] = pios_pwm_rcvr_id; #endif /* Set up the servo outputs */ PIOS_Servo_Init(&pios_servo_cfg); if (PIOS_I2C_Init(&pios_i2c_mag_adapter_id, &pios_i2c_mag_adapter_cfg)) { PIOS_DEBUG_Assert(0); } if (PIOS_I2C_Init(&pios_i2c_pressure_adapter_id, &pios_i2c_pressure_adapter_cfg)) { PIOS_DEBUG_Assert(0); } /* Set up the SPI interface to the accelerometer*/ if (PIOS_SPI_Init(&pios_spi_accel_id, &pios_spi_accel_cfg)) { PIOS_DEBUG_Assert(0); } /* Set up the SPI interface to the gyro */ if (PIOS_SPI_Init(&pios_spi_gyro_id, &pios_spi_gyro_cfg)) { PIOS_DEBUG_Assert(0); } PIOS_DELAY_WaitmS(500); /* #if defined(PIOS_INCLUDE_MPU6000) PIOS_MPU6000_Attach(pios_spi_gyro_id); PIOS_MPU6000_Init(&pios_mpu6000_cfg); #elif defined(PIOS_INCLUDE_L3GD20) PIOS_L3GD20_Attach(pios_spi_gyro_id); // PIOS_L3GD20_Init(&pios_l3gd20_cfg); #else PIOS_Assert(0); #endif */ PIOS_BMA180_Attach(pios_spi_accel_id); PIOS_BMA180_Init(&pios_bma180_cfg); PIOS_HMC5883_Init(&pios_hmc5883_cfg); PIOS_MS5611_Init(&pios_ms5611_cfg, pios_i2c_pressure_adapter_id); } /** * @} * @} */