/**
******************************************************************************
* @addtogroup Revolution Revolution configuration files
* @{
* @brief Configures the revolution board
* @{
*
* @file pios_board.c
* @author The OpenPilot Team, http://www.openpilot.org Copyright (C) 2011.
* @brief Defines board specific static initializers for hardware for the Revolution board.
* @see The GNU Public License (GPL) Version 3
*
*****************************************************************************/
/*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <pios.h>
#include <openpilot.h>
#include <pios_spi_priv.h>
#include <uavobjectsinit.h>
#include <hwsettings.h>
#include "manualcontrolsettings.h"
#if defined(PIOS_INCLUDE_SPI)
#define PIOS_FLASH_ON_ACCEL
/* SPI1 Interface
* - Used for BMA180 accelerometer
*/
void PIOS_SPI_accel_irq_handler(void);
void DMA2_Stream0_IRQHandler(void) __attribute__((alias("PIOS_SPI_accel_irq_handler")));
void DMA2_Stream3_IRQHandler(void) __attribute__((alias("PIOS_SPI_accel_irq_handler")));
static const struct pios_spi_cfg pios_spi_accel_cfg = {
.regs = SPI1,
.remap = GPIO_AF_SPI1,
.init = {
.SPI_Mode = SPI_Mode_Master,
.SPI_Direction = SPI_Direction_2Lines_FullDuplex,
.SPI_DataSize = SPI_DataSize_8b,
.SPI_NSS = SPI_NSS_Soft,
.SPI_FirstBit = SPI_FirstBit_MSB,
.SPI_CRCPolynomial = 7,
.SPI_CPOL = SPI_CPOL_High,
.SPI_CPHA = SPI_CPHA_2Edge,
.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_16,
},
.use_crc = false,
.dma = {
.irq = {
.flags = (DMA_IT_TCIF0 | DMA_IT_TEIF0 | DMA_IT_HTIF0),
.init = {
.NVIC_IRQChannel = DMA2_Stream0_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.channel = DMA2_Stream0,
.init = {
.DMA_Channel = DMA_Channel_3,
.DMA_PeripheralBaseAddr = (uint32_t)&(SPI1->DR),
.DMA_DIR = DMA_DIR_PeripheralToMemory,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_FIFOMode = DMA_FIFOMode_Disable,
/* .DMA_FIFOThreshold */
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
.tx = {
.channel = DMA2_Stream3,
.init = {
.DMA_Channel = DMA_Channel_3,
.DMA_PeripheralBaseAddr = (uint32_t)&(SPI1->DR),
.DMA_DIR = DMA_DIR_MemoryToPeripheral,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_High,
.DMA_FIFOMode = DMA_FIFOMode_Disable,
/* .DMA_FIFOThreshold */
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
},
.sclk = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_5,
.GPIO_Speed = GPIO_Speed_100MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.miso = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.mosi = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.slave_count = 2,
.ssel = { {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_4,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
} },
{
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_5,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
} },
}
};
static uint32_t pios_spi_accel_id;
void PIOS_SPI_accel_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_SPI_IRQ_Handler(pios_spi_accel_id);
}
/* SPI2 Interface
* - Used for gyro communications
*/
void PIOS_SPI_GYRO_irq_handler(void);
void DMA1_Stream3_IRQHandler(void) __attribute__((alias("PIOS_SPI_gyro_irq_handler")));
void DMA1_Stream4_IRQHandler(void) __attribute__((alias("PIOS_SPI_gyro_irq_handler")));
static const struct pios_spi_cfg pios_spi_gyro_cfg = {
.regs = SPI2,
.remap = GPIO_AF_SPI2,
.init = {
.SPI_Mode = SPI_Mode_Master,
.SPI_Direction = SPI_Direction_2Lines_FullDuplex,
.SPI_DataSize = SPI_DataSize_8b,
.SPI_NSS = SPI_NSS_Soft,
.SPI_FirstBit = SPI_FirstBit_MSB,
.SPI_CRCPolynomial = 7,
.SPI_CPOL = SPI_CPOL_High,
.SPI_CPHA = SPI_CPHA_2Edge,
.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_8,
},
.use_crc = false,
.dma = {
.irq = {
// Note this is the stream ID that triggers interrupts (in this case RX)
.flags = (DMA_IT_TCIF3 | DMA_IT_TEIF3 | DMA_IT_HTIF3),
.init = {
.NVIC_IRQChannel = DMA1_Stream3_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.channel = DMA1_Stream3,
.init = {
.DMA_Channel = DMA_Channel_0,
.DMA_PeripheralBaseAddr = (uint32_t) & (SPI2->DR),
.DMA_DIR = DMA_DIR_PeripheralToMemory,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
//TODO: Enable FIFO
.DMA_FIFOMode = DMA_FIFOMode_Disable,
.DMA_FIFOThreshold = DMA_FIFOThreshold_Full,
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
.tx = {
.channel = DMA1_Stream4,
.init = {
.DMA_Channel = DMA_Channel_0,
.DMA_PeripheralBaseAddr = (uint32_t) & (SPI2->DR),
.DMA_DIR = DMA_DIR_MemoryToPeripheral,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_FIFOMode = DMA_FIFOMode_Disable,
.DMA_FIFOThreshold = DMA_FIFOThreshold_Full,
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
},
.sclk = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_13,
.GPIO_Speed = GPIO_Speed_100MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.miso = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_14,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.mosi = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_15,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.slave_count = 1,
.ssel = { {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_12,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
} },
};
uint32_t pios_spi_gyro_id;
void PIOS_SPI_gyro_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_SPI_IRQ_Handler(pios_spi_gyro_id);
}
#if !defined(PIOS_FLASH_ON_ACCEL)
/* SPI3 Interface
* - Used for flash communications
*/
void PIOS_SPI_flash_irq_handler(void);
void DMA1_Stream0_IRQHandler(void) __attribute__((alias("PIOS_SPI_flash_irq_handler")));
void DMA1_Stream2_IRQHandler(void) __attribute__((alias("PIOS_SPI_flash_irq_handler")));
static const struct pios_spi_cfg pios_spi_flash_cfg = {
.regs = SPI3,
.remap = GPIO_AF_SPI3,
.init = {
.SPI_Mode = SPI_Mode_Master,
.SPI_Direction = SPI_Direction_2Lines_FullDuplex,
.SPI_DataSize = SPI_DataSize_8b,
.SPI_NSS = SPI_NSS_Soft,
.SPI_FirstBit = SPI_FirstBit_MSB,
.SPI_CRCPolynomial = 7,
.SPI_CPOL = SPI_CPOL_High,
.SPI_CPHA = SPI_CPHA_2Edge,
.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_2,
},
.use_crc = false,
.dma = {
.irq = {
// Note this is the stream ID that triggers interrupts (in this case RX)
.flags = (DMA_IT_TCIF3 | DMA_IT_TEIF3 | DMA_IT_HTIF3),
.init = {
.NVIC_IRQChannel = DMA1_Stream0_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.channel = DMA1_Stream0,
.init = {
.DMA_Channel = DMA_Channel_0,
.DMA_PeripheralBaseAddr = (uint32_t) & (SPI3->DR),
.DMA_DIR = DMA_DIR_PeripheralToMemory,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
//TODO: Enable FIFO
.DMA_FIFOMode = DMA_FIFOMode_Disable,
.DMA_FIFOThreshold = DMA_FIFOThreshold_Full,
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
.tx = {
.channel = DMA1_Stream2,
.init = {
.DMA_Channel = DMA_Channel_0,
.DMA_PeripheralBaseAddr = (uint32_t) & (SPI3->DR),
.DMA_DIR = DMA_DIR_MemoryToPeripheral,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_FIFOMode = DMA_FIFOMode_Disable,
.DMA_FIFOThreshold = DMA_FIFOThreshold_Full,
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
},
.sclk = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Speed = GPIO_Speed_100MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.miso = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.mosi = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_12,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.slave_count = 1,
.ssel = { {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_2,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
} },
};
uint32_t pios_spi_flash_id;
void PIOS_SPI_flash_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_SPI_IRQ_Handler(pios_spi_flash_id);
}
#endif /* PIOS_FLASH_ON_ACCEL */
#endif /* PIOS_INCLUDE_SPI */
#include <pios_usart_priv.h>
#if defined(PIOS_INCLUDE_GPS)
/*
* GPS USART
*/
static const struct pios_usart_cfg pios_usart_gps_cfg = {
.regs = USART1,
.remap = GPIO_AF_USART1,
.init = {
.USART_BaudRate = 57600,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl =
USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx | USART_Mode_Tx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART1_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_9,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
#define PIOS_COM_GPS_RX_BUF_LEN 192
#endif /* PIOS_INCLUDE_GPS */
#ifdef PIOS_INCLUDE_COM_AUX
/*
* AUX USART
*/
static const struct pios_usart_cfg pios_usart_aux_cfg = {
.regs = USART6,
.remap = GPIO_AF_USART6,
.init = {
.USART_BaudRate = 230400,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl =
USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx | USART_Mode_Tx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART6_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
#endif /* PIOS_COM_AUX */
#ifdef PIOS_INCLUDE_COM_TELEM
/*
* Telemetry on main USART
*/
static const struct pios_usart_cfg pios_usart_telem_main_cfg = {
.regs = USART6,
.remap = GPIO_AF_USART6,
.init = {
.USART_BaudRate = 57600,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl =
USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx | USART_Mode_Tx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART6_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
#define PIOS_COM_TELEM_RF_RX_BUF_LEN 512
#define PIOS_COM_TELEM_RF_TX_BUF_LEN 512
#endif /* PIOS_COM_TELEM */
#if defined(PIOS_INCLUDE_DSM)
/*
* Spektrum/JR DSM USART
*/
#include <pios_dsm_priv.h>
static const struct pios_usart_cfg pios_usart_dsm_main_cfg = {
.regs = USART3,
.remap = GPIO_AF_USART3,
.init = {
.USART_BaudRate = 115200,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl = USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART3_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
static const struct pios_dsm_cfg pios_dsm_main_cfg = {
.bind = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
};
static const struct pios_usart_cfg pios_usart_dsm_flexi_cfg = {
.regs = USART3,
.remap = GPIO_AF_USART3,
.init = {
.USART_BaudRate = 115200,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl = USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART3_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
static const struct pios_dsm_cfg pios_dsm_flexi_cfg = {
.bind = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
};
#endif /* PIOS_INCLUDE_DSM */
#if defined(PIOS_INCLUDE_COM)
#include <pios_com_priv.h>
#endif /* PIOS_INCLUDE_COM */
#if defined(PIOS_INCLUDE_I2C)
#include <pios_i2c_priv.h>
/*
* I2C Adapters
*/
void PIOS_I2C_mag_adapter_ev_irq_handler(void);
void PIOS_I2C_mag_adapter_er_irq_handler(void);
void I2C1_EV_IRQHandler()
__attribute__ ((alias("PIOS_I2C_mag_adapter_ev_irq_handler")));
void I2C1_ER_IRQHandler()
__attribute__ ((alias("PIOS_I2C_mag_adapter_er_irq_handler")));
static const struct pios_i2c_adapter_cfg pios_i2c_mag_adapter_cfg = {
.regs = I2C1,
.remap = GPIO_AF_I2C1,
.init = {
.I2C_Mode = I2C_Mode_I2C,
.I2C_OwnAddress1 = 0,
.I2C_Ack = I2C_Ack_Enable,
.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit,
.I2C_DutyCycle = I2C_DutyCycle_2,
.I2C_ClockSpeed = 400000, /* bits/s */
},
.transfer_timeout_ms = 50,
.scl = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.sda = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.event = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C1_EV_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.error = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C1_ER_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
uint32_t pios_i2c_mag_adapter_id;
void PIOS_I2C_mag_adapter_ev_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_EV_IRQ_Handler(pios_i2c_mag_adapter_id);
}
void PIOS_I2C_mag_adapter_er_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_ER_IRQ_Handler(pios_i2c_mag_adapter_id);
}
void PIOS_I2C_flexiport_adapter_ev_irq_handler(void);
void PIOS_I2C_flexiport_adapter_er_irq_handler(void);
void I2C2_EV_IRQHandler() __attribute__ ((alias ("PIOS_I2C_flexiport_adapter_ev_irq_handler")));
void I2C2_ER_IRQHandler() __attribute__ ((alias ("PIOS_I2C_flexiport_adapter_er_irq_handler")));
static const struct pios_i2c_adapter_cfg pios_i2c_flexiport_adapter_cfg = {
.regs = I2C2,
.remap = GPIO_AF_I2C2,
.init = {
.I2C_Mode = I2C_Mode_I2C,
.I2C_OwnAddress1 = 0,
.I2C_Ack = I2C_Ack_Enable,
.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit,
.I2C_DutyCycle = I2C_DutyCycle_2,
.I2C_ClockSpeed = 400000, /* bits/s */
},
.transfer_timeout_ms = 50,
.scl = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.sda = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.event = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C2_EV_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.error = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C2_ER_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
uint32_t pios_i2c_flexiport_adapter_id;
void PIOS_I2C_flexiport_adapter_ev_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_EV_IRQ_Handler(pios_i2c_flexiport_adapter_id);
}
void PIOS_I2C_flexiport_adapter_er_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_ER_IRQ_Handler(pios_i2c_flexiport_adapter_id);
}
void PIOS_I2C_pressure_adapter_ev_irq_handler(void);
void PIOS_I2C_pressure_adapter_er_irq_handler(void);
void I2C3_EV_IRQHandler() __attribute__ ((alias ("PIOS_I2C_pressure_adapter_ev_irq_handler")));
void I2C3_ER_IRQHandler() __attribute__ ((alias ("PIOS_I2C_pressure_adapter_er_irq_handler")));
static const struct pios_i2c_adapter_cfg pios_i2c_pressure_adapter_cfg = {
.regs = I2C3,
.remap = GPIO_AF_I2C3,
.init = {
.I2C_Mode = I2C_Mode_I2C,
.I2C_OwnAddress1 = 0,
.I2C_Ack = I2C_Ack_Enable,
.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit,
.I2C_DutyCycle = I2C_DutyCycle_2,
.I2C_ClockSpeed = 40000, /* bits/s */
},
.transfer_timeout_ms = 50,
.scl = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_8,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.sda = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_9,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.event = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C3_EV_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.error = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C3_ER_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
uint32_t pios_i2c_pressure_adapter_id;
void PIOS_I2C_pressure_adapter_ev_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_EV_IRQ_Handler(pios_i2c_pressure_adapter_id);
}
void PIOS_I2C_pressure_adapter_er_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_ER_IRQ_Handler(pios_i2c_pressure_adapter_id);
}
#endif /* PIOS_INCLUDE_I2C */
#if defined(PIOS_INCLUDE_RTC)
/*
* Realtime Clock (RTC)
*/
#include <pios_rtc_priv.h>
void PIOS_RTC_IRQ_Handler (void);
void RTC_WKUP_IRQHandler() __attribute__ ((alias ("PIOS_RTC_IRQ_Handler")));
static const struct pios_rtc_cfg pios_rtc_main_cfg = {
.clksrc = RCC_RTCCLKSource_HSE_Div16, // Divide 8 Mhz crystal down to 1
// For some reason it's acting like crystal is 16 Mhz. This clock is then divided
// by another 16 to give a nominal 62.5 khz clock
.prescaler = 100, // Every 100 cycles gives 625 Hz
.irq = {
.init = {
.NVIC_IRQChannel = RTC_WKUP_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
void PIOS_RTC_IRQ_Handler (void)
{
PIOS_RTC_irq_handler ();
}
#endif
#include "pios_tim_priv.h"
static const TIM_TimeBaseInitTypeDef tim_3_5_9_10_11_time_base = {
.TIM_Prescaler = (PIOS_MASTER_CLOCK / 1000000) - 1,
.TIM_ClockDivision = TIM_CKD_DIV1,
.TIM_CounterMode = TIM_CounterMode_Up,
.TIM_Period = ((1000000 / PIOS_SERVO_UPDATE_HZ) - 1),
.TIM_RepetitionCounter = 0x0000,
};
static const struct pios_tim_clock_cfg tim_3_cfg = {
.timer = TIM3,
.time_base_init = &tim_3_5_9_10_11_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM3_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_5_cfg = {
.timer = TIM5,
.time_base_init = &tim_3_5_9_10_11_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM5_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_9_cfg = {
.timer = TIM9,
.time_base_init = &tim_3_5_9_10_11_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM1_BRK_TIM9_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_10_cfg = {
.timer = TIM10,
.time_base_init = &tim_3_5_9_10_11_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM1_UP_TIM10_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_11_cfg = {
.timer = TIM11,
.time_base_init = &tim_3_5_9_10_11_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM1_TRG_COM_TIM11_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
// Set up timers that only have inputs
static const TIM_TimeBaseInitTypeDef tim_1_4_time_base = {
.TIM_Prescaler = (PIOS_MASTER_CLOCK / 1000000) - 1,
.TIM_ClockDivision = TIM_CKD_DIV1,
.TIM_CounterMode = TIM_CounterMode_Up,
.TIM_Period = 0xFFFF,
.TIM_RepetitionCounter = 0x0000,
};
static const struct pios_tim_clock_cfg tim_1_cfg = {
.timer = TIM1,
.time_base_init = &tim_1_4_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM1_CC_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_4_cfg = {
.timer = TIM4,
.time_base_init = &tim_1_4_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM4_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
/**
* Pios servo configuration structures
*/
#include <pios_servo_priv.h>
static const struct pios_tim_channel pios_tim_servoport_all_pins[] = {
{
.timer = TIM9,
.timer_chan = TIM_Channel_1,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_5,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource5,
},
.remap = GPIO_AF_TIM9,
},
{
.timer = TIM9,
.timer_chan = TIM_Channel_2,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource6,
},
.remap = GPIO_AF_TIM9,
},
{
.timer = TIM10,
.timer_chan = TIM_Channel_1,
.pin = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_8,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource8,
},
.remap = GPIO_AF_TIM10,
},
{
.timer = TIM11,
.timer_chan = TIM_Channel_1,
.pin = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_9,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource9,
},
.remap = GPIO_AF_TIM11,
},
{
.timer = TIM5,
.timer_chan = TIM_Channel_3,
.pin = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_2,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource2,
},
.remap = GPIO_AF_TIM5,
},
{
.timer = TIM5,
.timer_chan = TIM_Channel_4,
.pin = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_3,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource3,
},
.remap = GPIO_AF_TIM5,
},
{
.timer = TIM3,
.timer_chan = TIM_Channel_3,
.pin = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_0,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource0,
},
.remap = GPIO_AF_TIM3,
},
{
.timer = TIM3,
.timer_chan = TIM_Channel_3,
.pin = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_1,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource1,
},
.remap = GPIO_AF_TIM3,
},
};
const struct pios_servo_cfg pios_servo_cfg = {
.tim_oc_init = {
.TIM_OCMode = TIM_OCMode_PWM1,
.TIM_OutputState = TIM_OutputState_Enable,
.TIM_OutputNState = TIM_OutputNState_Disable,
.TIM_Pulse = PIOS_SERVOS_INITIAL_POSITION,
.TIM_OCPolarity = TIM_OCPolarity_High,
.TIM_OCNPolarity = TIM_OCPolarity_High,
.TIM_OCIdleState = TIM_OCIdleState_Reset,
.TIM_OCNIdleState = TIM_OCNIdleState_Reset,
},
.channels = pios_tim_servoport_all_pins,
.num_channels = NELEMENTS(pios_tim_servoport_all_pins),
};
/*
* PWM Inputs
*/
#if defined(PIOS_INCLUDE_PWM) || defined(PIOS_INCLUDE_PPM)
#include <pios_pwm_priv.h>
static const struct pios_tim_channel pios_tim_rcvrport_all_channels[] = {
{
.timer = TIM4,
.timer_chan = TIM_Channel_4,
.pin = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_15,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource15,
},
.remap = GPIO_AF_TIM4,
},
{
.timer = TIM4,
.timer_chan = TIM_Channel_3,
.pin = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_14,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource14,
},
.remap = GPIO_AF_TIM4,
},
{
.timer = TIM4,
.timer_chan = TIM_Channel_2,
.pin = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_13,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource13,
},
.remap = GPIO_AF_TIM4,
},
{
.timer = TIM4,
.timer_chan = TIM_Channel_1,
.pin = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_12,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource12,
},
.remap = GPIO_AF_TIM4,
},
{
.timer = TIM1,
.timer_chan = TIM_Channel_4,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_14,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource14,
},
.remap = GPIO_AF_TIM1,
},
{
.timer = TIM1,
.timer_chan = TIM_Channel_3,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_13,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource13,
},
.remap = GPIO_AF_TIM1,
},
{
.timer = TIM1,
.timer_chan = TIM_Channel_2,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource11,
},
.remap = GPIO_AF_TIM1,
},
{
.timer = TIM1,
.timer_chan = TIM_Channel_1,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_9,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource1,
},
.remap = GPIO_AF_TIM1,
},
};
const struct pios_pwm_cfg pios_pwm_cfg = {
.tim_ic_init = {
.TIM_ICPolarity = TIM_ICPolarity_Rising,
.TIM_ICSelection = TIM_ICSelection_DirectTI,
.TIM_ICPrescaler = TIM_ICPSC_DIV1,
.TIM_ICFilter = 0x0,
},
.channels = pios_tim_rcvrport_all_channels,
.num_channels = NELEMENTS(pios_tim_rcvrport_all_channels),
};
#endif
/*
* PPM Input
*/
#if defined(PIOS_INCLUDE_PPM)
#include <pios_ppm_priv.h>
static const struct pios_ppm_cfg pios_ppm_cfg = {
.tim_ic_init = {
.TIM_ICPolarity = TIM_ICPolarity_Rising,
.TIM_ICSelection = TIM_ICSelection_DirectTI,
.TIM_ICPrescaler = TIM_ICPSC_DIV1,
.TIM_ICFilter = 0x0,
.TIM_Channel = TIM_Channel_2,
},
/* Use only the first channel for ppm */
.channels = &pios_tim_rcvrport_all_channels[0],
.num_channels = 1,
};
#endif //PPM
#if defined(PIOS_INCLUDE_RCVR)
#include "pios_rcvr_priv.h"
/* One slot per selectable receiver group.
* eg. PWM, PPM, GCS, SPEKTRUM1, SPEKTRUM2, SBUS
* NOTE: No slot in this map for NONE.
*/
uint32_t pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_NONE];
#endif
extern const struct pios_com_driver pios_usart_com_driver;
uint32_t pios_com_aux_id;
uint32_t pios_com_gps_id;
uint32_t pios_com_telem_usb_id;
uint32_t pios_com_telem_rf_id;
/**
* Sensor configurations
*/
#if defined(PIOS_INCLUDE_HMC5883)
#include "pios_hmc5883.h"
static const struct pios_exti_cfg pios_exti_hmc5883_cfg __exti_config = {
.vector = PIOS_HMC5883_IRQHandler,
.line = EXTI_Line5,
.pin = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_5,
.GPIO_Speed = GPIO_Speed_100MHz,
.GPIO_Mode = GPIO_Mode_IN,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.irq = {
.init = {
.NVIC_IRQChannel = EXTI9_5_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_LOW,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.exti = {
.init = {
.EXTI_Line = EXTI_Line5, // matches above GPIO pin
.EXTI_Mode = EXTI_Mode_Interrupt,
.EXTI_Trigger = EXTI_Trigger_Rising,
.EXTI_LineCmd = ENABLE,
},
},
};
static const struct pios_hmc5883_cfg pios_hmc5883_cfg = {
.exti_cfg = &pios_exti_hmc5883_cfg,
.M_ODR = PIOS_HMC5883_ODR_75,
.Meas_Conf = PIOS_HMC5883_MEASCONF_NORMAL,
.Gain = PIOS_HMC5883_GAIN_1_9,
.Mode = PIOS_HMC5883_MODE_CONTINUOUS,
};
#endif /* PIOS_INCLUDE_HMC5883 */
/**
* Configuration for the MS5611 chip
*/
#if defined(PIOS_INCLUDE_MS5611)
#include "pios_ms5611.h"
static const struct pios_ms5611_cfg pios_ms5611_cfg = {
.oversampling = 1,
};
#endif /* PIOS_INCLUDE_MS5611 */
/**
* Configuration for the BMA180 chip
*/
#if defined(PIOS_INCLUDE_BMA180)
#include "pios_bma180.h"
static const struct pios_exti_cfg pios_exti_bma180_cfg __exti_config = {
.vector = PIOS_BMA180_IRQHandler,
.line = EXTI_Line4,
.pin = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_4,
.GPIO_Speed = GPIO_Speed_100MHz,
.GPIO_Mode = GPIO_Mode_IN,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.irq = {
.init = {
.NVIC_IRQChannel = EXTI4_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_LOW,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.exti = {
.init = {
.EXTI_Line = EXTI_Line4, // matches above GPIO pin
.EXTI_Mode = EXTI_Mode_Interrupt,
.EXTI_Trigger = EXTI_Trigger_Rising,
.EXTI_LineCmd = ENABLE,
},
},
};
static const struct pios_bma180_cfg pios_bma180_cfg = {
.exti_cfg = &pios_exti_bma180_cfg,
.bandwidth = BMA_BW_600HZ,
.range = BMA_RANGE_8G,
};
#endif /* PIOS_INCLUDE_BMA180 */
/**
* Configuration for the MPU6000 chip
*/
#if defined(PIOS_INCLUDE_MPU6000)
#include "pios_mpu6000.h"
static const struct pios_exti_cfg pios_exti_mpu6000_cfg __exti_config = {
.vector = PIOS_MPU6000_IRQHandler,
.line = EXTI_Line8,
.pin = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_8,
.GPIO_Speed = GPIO_Speed_100MHz,
.GPIO_Mode = GPIO_Mode_IN,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.irq = {
.init = {
.NVIC_IRQChannel = EXTI9_5_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.exti = {
.init = {
.EXTI_Line = EXTI_Line8, // matches above GPIO pin
.EXTI_Mode = EXTI_Mode_Interrupt,
.EXTI_Trigger = EXTI_Trigger_Rising,
.EXTI_LineCmd = ENABLE,
},
},
};
static const struct pios_mpu6000_cfg pios_mpu6000_cfg = {
.exti_cfg = &pios_exti_mpu6000_cfg,
.Fifo_store = PIOS_MPU6000_FIFO_TEMP_OUT | PIOS_MPU6000_FIFO_GYRO_X_OUT | PIOS_MPU6000_FIFO_GYRO_Y_OUT | PIOS_MPU6000_FIFO_GYRO_Z_OUT,
// Clock at 8 khz, downsampled by 8 for 1khz
.Smpl_rate_div = 7,
.interrupt_cfg = PIOS_MPU6000_INT_CLR_ANYRD,
.interrupt_en = PIOS_MPU6000_INTEN_DATA_RDY,
.User_ctl = PIOS_MPU6000_USERCTL_FIFO_EN,
.Pwr_mgmt_clk = PIOS_MPU6000_PWRMGMT_PLL_X_CLK,
.gyro_range = PIOS_MPU6000_SCALE_500_DEG,
.filter = PIOS_MPU6000_LOWPASS_256_HZ
};
#endif /* PIOS_INCLUDE_MPU6000 */
/**
* Configuration for L3GD20 chip
*/
#if defined(PIOS_INCLUDE_L3GD20)
#include "pios_l3gd20.h"
static const struct pios_exti_cfg pios_exti_l3gd20_cfg __exti_config = {
.vector = PIOS_L3GD20_IRQHandler,
.line = EXTI_Line8,
.pin = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_8,
.GPIO_Speed = GPIO_Speed_100MHz,
.GPIO_Mode = GPIO_Mode_IN,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.irq = {
.init = {
.NVIC_IRQChannel = EXTI9_5_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.exti = {
.init = {
.EXTI_Line = EXTI_Line8, // matches above GPIO pin
.EXTI_Mode = EXTI_Mode_Interrupt,
.EXTI_Trigger = EXTI_Trigger_Rising,
.EXTI_LineCmd = ENABLE,
},
},
};
static const struct pios_l3gd20_cfg pios_l3gd20_cfg = {
.exti_cfg = &pios_exti_l3gd20_cfg,
.range = PIOS_L3GD20_SCALE_500_DEG,
};
#endif /* PIOS_INCLUDE_L3GD20 */
/**
* PIOS_Board_Init()
* initializes all the core subsystems on this specific hardware
* called from System/openpilot.c
*/
void PIOS_Board_Init(void) {
/* Delay system */
PIOS_DELAY_Init();
#ifdef PIOS_DEBUG_ENABLE_DEBUG_PINS
PIOS_DEBUG_Init(&pios_tim_servo_all_channels, NELEMENTS(pios_tim_servo_all_channels));
#endif /* PIOS_DEBUG_ENABLE_DEBUG_PINS */
/* Set up the SPI interface to the accelerometer*/
if (PIOS_SPI_Init(&pios_spi_accel_id, &pios_spi_accel_cfg)) {
PIOS_DEBUG_Assert(0);
}
/* Set up the SPI interface to the gyro */
if (PIOS_SPI_Init(&pios_spi_gyro_id, &pios_spi_gyro_cfg)) {
PIOS_DEBUG_Assert(0);
}
#if !defined(PIOS_FLASH_ON_ACCEL)
/* Set up the SPI interface to the flash */
if (PIOS_SPI_Init(&pios_spi_flash_id, &pios_spi_flash_cfg)) {
PIOS_DEBUG_Assert(0);
}
PIOS_Flash_W25X_Init(pios_spi_flash_id, 0);
#else
PIOS_Flash_W25X_Init(pios_spi_accel_id, 1);
#endif
PIOS_FLASHFS_Init();
/* Initialize UAVObject libraries */
EventDispatcherInitialize();
UAVObjInitialize();
HwSettingsInitialize();
#if defined(PIOS_INCLUDE_RTC)
PIOS_RTC_Init(&pios_rtc_main_cfg);
#endif
/* Initialize the alarms library */
AlarmsInitialize();
/* Initialize the task monitor library */
TaskMonitorInitialize();
/* Set up pulse timers */
PIOS_TIM_InitClock(&tim_1_cfg);
PIOS_TIM_InitClock(&tim_3_cfg);
PIOS_TIM_InitClock(&tim_4_cfg);
PIOS_TIM_InitClock(&tim_4_cfg);
PIOS_TIM_InitClock(&tim_5_cfg);
PIOS_TIM_InitClock(&tim_9_cfg);
PIOS_TIM_InitClock(&tim_10_cfg);
PIOS_TIM_InitClock(&tim_11_cfg);
/* IAP System Setup */
//PIOS_IAP_Init();
#if defined(PIOS_INCLUDE_COM)
#if defined(PIOS_INCLUDE_GPS)
uint32_t pios_usart_gps_id;
if (PIOS_USART_Init(&pios_usart_gps_id, &pios_usart_telem_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_GPS_RX_BUF_LEN);
PIOS_Assert(rx_buffer);
if (PIOS_COM_Init(&pios_com_gps_id, &pios_usart_com_driver, pios_usart_gps_id,
rx_buffer, PIOS_COM_GPS_RX_BUF_LEN,
NULL, 0)) {
PIOS_Assert(0);
}
#endif /* PIOS_INCLUDE_GPS */
#if defined(PIOS_INCLUDE_COM_AUX)
{
uint32_t pios_usart_aux_id;
if (PIOS_USART_Init(&pios_usart_aux_id, &pios_usart_aux_cfg)) {
PIOS_DEBUG_Assert(0);
}
const uint32_t BUF_SIZE = 512;
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(BUF_SIZE);
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(BUF_SIZE);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_aux_id, &pios_usart_com_driver, pios_usart_aux_id,
rx_buffer, BUF_SIZE,
tx_buffer, BUF_SIZE)) {
PIOS_DEBUG_Assert(0);
}
}
#else
pios_com_aux_id = 0;
#endif /* PIOS_INCLUDE_COM_AUX */
#if defined(PIOS_INCLUDE_COM_TELEM)
{ /* Eventually add switch for this port function */
uint32_t pios_usart_telem_rf_id;
if (PIOS_USART_Init(&pios_usart_telem_rf_id, &pios_usart_gps_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_RF_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_RF_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_rf_id, &pios_usart_com_driver, pios_usart_telem_rf_id,
rx_buffer, PIOS_COM_TELEM_RF_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_RF_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#else
pios_com_telem_rf_id = 0;
#endif /* PIOS_INCLUDE_COM_TELEM */
#endif /* PIOS_INCLUDE_COM */
// Set up spektrum receiver
enum pios_dsm_proto proto;
proto = PIOS_DSM_PROTO_DSM2;
uint32_t pios_usart_dsm_id;
if (PIOS_USART_Init(&pios_usart_dsm_id, &pios_usart_dsm_main_cfg)) {
PIOS_Assert(0);
}
uint32_t pios_dsm_id;
if (PIOS_DSM_Init(&pios_dsm_id,
&pios_dsm_main_cfg,
&pios_usart_com_driver,
pios_usart_dsm_id,
proto, 0)) {
PIOS_Assert(0);
}
uint32_t pios_dsm_rcvr_id;
if (PIOS_RCVR_Init(&pios_dsm_rcvr_id, &pios_dsm_rcvr_driver, pios_dsm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_DSMMAINPORT] = pios_dsm_rcvr_id;
#if defined(PIOS_INCLUDE_PWM) && defined(PIOS_INCLUDE_RCVR)
/* Set up the receiver port. Later this should be optional */
uint32_t pios_pwm_id;
PIOS_PWM_Init(&pios_pwm_id, &pios_pwm_cfg);
uint32_t pios_pwm_rcvr_id;
if (PIOS_RCVR_Init(&pios_pwm_rcvr_id, &pios_pwm_rcvr_driver, pios_pwm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PWM] = pios_pwm_rcvr_id;
#endif
/* Set up the servo outputs */
PIOS_Servo_Init(&pios_servo_cfg);
if (PIOS_I2C_Init(&pios_i2c_mag_adapter_id, &pios_i2c_mag_adapter_cfg)) {
PIOS_DEBUG_Assert(0);
}
if (PIOS_I2C_Init(&pios_i2c_pressure_adapter_id, &pios_i2c_pressure_adapter_cfg)) {
PIOS_DEBUG_Assert(0);
}
PIOS_DELAY_WaitmS(500);
#if defined(PIOS_INCLUDE_BMA180)
PIOS_BMA180_Init(pios_spi_accel_id, 0, &pios_bma180_cfg);
PIOS_Assert(PIOS_BMA180_Test() == 0);
#endif
#if defined(PIOS_INCLUDE_MPU6000)
PIOS_MPU6000_Attach(pios_spi_gyro_id);
PIOS_MPU6000_Init(&pios_mpu6000_cfg);
PIOS_Assert(PIOS_MPU6000_Test() == 0);
#elif defined(PIOS_INCLUDE_L3GD20)
PIOS_L3GD20_Init(pios_spi_gyro_id, 0, &pios_l3gd20_cfg);
PIOS_Assert(PIOS_L3GD20_Test() == 0);
#else
PIOS_Assert(0);
#endif
PIOS_HMC5883_Init(&pios_hmc5883_cfg);
PIOS_MS5611_Init(&pios_ms5611_cfg, pios_i2c_pressure_adapter_id);
}
/**
* @}
* @}
*/