rooty/LibrePilot
1
0
Fork 0
mirror of https://bitbucket.org/librepilot/librepilot.git synced 2024-12-02 10:24:11 +01:00
Code Issues Releases Activity
93bad2e8c2
LibrePilot/flight/targets/boards/revoproto/board_hw_defs.c
Richard Flay (Hyper) a2d8544931 OP-931: adds -Wextra compiler option for the flight code, and makes the bazillion code changes required 
to make the flight code compile again. Needs careful review, particularly all the fixes for the
signed vs unsigned comparisons.

+review OPReview-459
2013-05-05 16:32:24 +09:30

2044 lines
52 KiB
C
Raw Blame History

/**
******************************************************************************
* @file board_hw_defs.c
* @author The OpenPilot Team, http://www.openpilot.org Copyright (C) 2012.
* @author PhoenixPilot, http://github.com/PhoenixPilot, Copyright (C) 2012
* @addtogroup OpenPilotSystem OpenPilot System
* @{
* @addtogroup OpenPilotCore OpenPilot Core
* @{
* @brief Defines board specific static initializers for hardware for the Revolution board.
*****************************************************************************/
/*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#if defined(PIOS_INCLUDE_LED)
#include <pios_led_priv.h>
static const struct pios_led pios_leds[] = {
[PIOS_LED_HEARTBEAT] = {
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_2,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
},
[PIOS_LED_ALARM] = {
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_3,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
},
};
static const struct pios_led_cfg pios_led_cfg = {
.leds = pios_leds,
.num_leds = NELEMENTS(pios_leds),
};
const struct pios_led_cfg * PIOS_BOARD_HW_DEFS_GetLedCfg (__attribute__((unused)) uint32_t board_revision)
{
return &pios_led_cfg;
}
#endif /* PIOS_INCLUDE_LED */
#if defined(PIOS_INCLUDE_SPI)
#include <pios_spi_priv.h>
/* SPI1 Interface
* - Used for BMA180 accelerometer
*/
void PIOS_SPI_accel_irq_handler(void);
void DMA2_Stream0_IRQHandler(void) __attribute__((alias("PIOS_SPI_accel_irq_handler")));
void DMA2_Stream3_IRQHandler(void) __attribute__((alias("PIOS_SPI_accel_irq_handler")));
static const struct pios_spi_cfg pios_spi_accel_cfg = {
.regs = SPI1,
.remap = GPIO_AF_SPI1,
.init = {
.SPI_Mode = SPI_Mode_Master,
.SPI_Direction = SPI_Direction_2Lines_FullDuplex,
.SPI_DataSize = SPI_DataSize_8b,
.SPI_NSS = SPI_NSS_Soft,
.SPI_FirstBit = SPI_FirstBit_MSB,
.SPI_CRCPolynomial = 7,
.SPI_CPOL = SPI_CPOL_High,
.SPI_CPHA = SPI_CPHA_2Edge,
.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_16,
},
.use_crc = false,
.dma = {
.irq = {
.flags = (DMA_IT_TCIF0 | DMA_IT_TEIF0 | DMA_IT_HTIF0),
.init = {
.NVIC_IRQChannel = DMA2_Stream0_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.channel = DMA2_Stream0,
.init = {
.DMA_Channel = DMA_Channel_3,
.DMA_PeripheralBaseAddr = (uint32_t)&(SPI1->DR),
.DMA_DIR = DMA_DIR_PeripheralToMemory,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_FIFOMode = DMA_FIFOMode_Disable,
/* .DMA_FIFOThreshold */
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
.tx = {
.channel = DMA2_Stream3,
.init = {
.DMA_Channel = DMA_Channel_3,
.DMA_PeripheralBaseAddr = (uint32_t)&(SPI1->DR),
.DMA_DIR = DMA_DIR_MemoryToPeripheral,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_High,
.DMA_FIFOMode = DMA_FIFOMode_Disable,
/* .DMA_FIFOThreshold */
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
},
.sclk = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_5,
.GPIO_Speed = GPIO_Speed_100MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.miso = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.mosi = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.slave_count = 2,
.ssel = { {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_4,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
} },
{
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_5,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
} },
}
};
static uint32_t pios_spi_accel_id;
void PIOS_SPI_accel_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_SPI_IRQ_Handler(pios_spi_accel_id);
}
/* SPI2 Interface
* - Used for gyro communications
*/
void PIOS_SPI_GYRO_irq_handler(void);
void DMA1_Stream3_IRQHandler(void) __attribute__((alias("PIOS_SPI_gyro_irq_handler")));
void DMA1_Stream4_IRQHandler(void) __attribute__((alias("PIOS_SPI_gyro_irq_handler")));
static const struct pios_spi_cfg pios_spi_gyro_cfg = {
.regs = SPI2,
.remap = GPIO_AF_SPI2,
.init = {
.SPI_Mode = SPI_Mode_Master,
.SPI_Direction = SPI_Direction_2Lines_FullDuplex,
.SPI_DataSize = SPI_DataSize_8b,
.SPI_NSS = SPI_NSS_Soft,
.SPI_FirstBit = SPI_FirstBit_MSB,
.SPI_CRCPolynomial = 7,
.SPI_CPOL = SPI_CPOL_High,
.SPI_CPHA = SPI_CPHA_2Edge,
.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_8,
},
.use_crc = false,
.dma = {
.irq = {
// Note this is the stream ID that triggers interrupts (in this case RX)
.flags = (DMA_IT_TCIF3 | DMA_IT_TEIF3 | DMA_IT_HTIF3),
.init = {
.NVIC_IRQChannel = DMA1_Stream3_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.channel = DMA1_Stream3,
.init = {
.DMA_Channel = DMA_Channel_0,
.DMA_PeripheralBaseAddr = (uint32_t) & (SPI2->DR),
.DMA_DIR = DMA_DIR_PeripheralToMemory,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
//TODO: Enable FIFO
.DMA_FIFOMode = DMA_FIFOMode_Disable,
.DMA_FIFOThreshold = DMA_FIFOThreshold_Full,
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
.tx = {
.channel = DMA1_Stream4,
.init = {
.DMA_Channel = DMA_Channel_0,
.DMA_PeripheralBaseAddr = (uint32_t) & (SPI2->DR),
.DMA_DIR = DMA_DIR_MemoryToPeripheral,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_FIFOMode = DMA_FIFOMode_Disable,
.DMA_FIFOThreshold = DMA_FIFOThreshold_Full,
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
},
.sclk = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_13,
.GPIO_Speed = GPIO_Speed_100MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.miso = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_14,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.mosi = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_15,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.slave_count = 1,
.ssel = { {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_12,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
} },
};
uint32_t pios_spi_gyro_id;
void PIOS_SPI_gyro_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_SPI_IRQ_Handler(pios_spi_gyro_id);
}
#if !defined(PIOS_FLASH_ON_ACCEL)
/* SPI3 Interface
* - Used for flash communications
*/
void PIOS_SPI_flash_irq_handler(void);
void DMA1_Stream0_IRQHandler(void) __attribute__((alias("PIOS_SPI_flash_irq_handler")));
void DMA1_Stream5_IRQHandler(void) __attribute__((alias("PIOS_SPI_flash_irq_handler")));
static const struct pios_spi_cfg pios_spi_flash_cfg = {
.regs = SPI3,
.remap = GPIO_AF_SPI3,
.init = {
.SPI_Mode = SPI_Mode_Master,
.SPI_Direction = SPI_Direction_2Lines_FullDuplex,
.SPI_DataSize = SPI_DataSize_8b,
.SPI_NSS = SPI_NSS_Soft,
.SPI_FirstBit = SPI_FirstBit_MSB,
.SPI_CRCPolynomial = 7,
.SPI_CPOL = SPI_CPOL_High,
.SPI_CPHA = SPI_CPHA_2Edge,
.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_2,
},
.use_crc = false,
.dma = {
.irq = {
// Note this is the stream ID that triggers interrupts (in this case RX)
.flags = (DMA_IT_TCIF0 | DMA_IT_TEIF0 | DMA_IT_HTIF0),
.init = {
.NVIC_IRQChannel = DMA1_Stream0_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.channel = DMA1_Stream0,
.init = {
.DMA_Channel = DMA_Channel_0,
.DMA_PeripheralBaseAddr = (uint32_t) & (SPI3->DR),
.DMA_DIR = DMA_DIR_PeripheralToMemory,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
//TODO: Enable FIFO
.DMA_FIFOMode = DMA_FIFOMode_Disable,
.DMA_FIFOThreshold = DMA_FIFOThreshold_Full,
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
.tx = {
.channel = DMA1_Stream5,
.init = {
.DMA_Channel = DMA_Channel_0,
.DMA_PeripheralBaseAddr = (uint32_t) & (SPI3->DR),
.DMA_DIR = DMA_DIR_MemoryToPeripheral,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_FIFOMode = DMA_FIFOMode_Disable,
.DMA_FIFOThreshold = DMA_FIFOThreshold_Full,
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
},
.sclk = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Speed = GPIO_Speed_100MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.miso = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.mosi = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_12,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.slave_count = 1,
.ssel = { {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_2,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
} },
};
uint32_t pios_spi_flash_id;
void PIOS_SPI_flash_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_SPI_IRQ_Handler(pios_spi_flash_id);
}
#endif /* PIOS_FLASH_ON_ACCEL */
#endif /* PIOS_INCLUDE_SPI */
#if defined(PIOS_INCLUDE_FLASH)
#include "pios_flashfs_logfs_priv.h"
#include "pios_flash_jedec_priv.h"
static const struct flashfs_logfs_cfg flashfs_m25p_cfg = {
.fs_magic = 0x99abceef,
.total_fs_size = 0x00200000, /* 2M bytes (32 sectors = entire chip) */
.arena_size = 0x00010000, /* 256 * slot size */
.slot_size = 0x00000100, /* 256 bytes */
.start_offset = 0, /* start at the beginning of the chip */
.sector_size = 0x00010000, /* 64K bytes */
.page_size = 0x00000100, /* 256 bytes */
};
#endif /* PIOS_INCLUDE_FLASH */
#if defined(PIOS_OVERO_SPI)
/* SPI3 Interface
* - Used for flash communications
*/
#include <pios_overo_priv.h>
void PIOS_OVERO_irq_handler(void);
void DMA1_Stream7_IRQHandler(void) __attribute__((alias("PIOS_OVERO_irq_handler")));
static const struct pios_overo_cfg pios_overo_cfg = {
.regs = SPI3,
.remap = GPIO_AF_SPI3,
.init = {
.SPI_Mode = SPI_Mode_Slave,
.SPI_Direction = SPI_Direction_2Lines_FullDuplex,
.SPI_DataSize = SPI_DataSize_8b,
.SPI_NSS = SPI_NSS_Hard,
.SPI_FirstBit = SPI_FirstBit_MSB,
.SPI_CRCPolynomial = 7,
.SPI_CPOL = SPI_CPOL_High,
.SPI_CPHA = SPI_CPHA_2Edge,
.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_2,
},
.use_crc = false,
.dma = {
.irq = {
// Note this is the stream ID that triggers interrupts (in this case TX)
.flags = (DMA_IT_TCIF7),
.init = {
.NVIC_IRQChannel = DMA1_Stream7_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.channel = DMA1_Stream0,
.init = {
.DMA_Channel = DMA_Channel_0,
.DMA_PeripheralBaseAddr = (uint32_t) & (SPI3->DR),
.DMA_DIR = DMA_DIR_PeripheralToMemory,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Circular,
.DMA_Priority = DMA_Priority_Medium,
//TODO: Enable FIFO
.DMA_FIFOMode = DMA_FIFOMode_Disable,
.DMA_FIFOThreshold = DMA_FIFOThreshold_Full,
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
.tx = {
.channel = DMA1_Stream7,
.init = {
.DMA_Channel = DMA_Channel_0,
.DMA_PeripheralBaseAddr = (uint32_t) & (SPI3->DR),
.DMA_DIR = DMA_DIR_MemoryToPeripheral,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Circular,
.DMA_Priority = DMA_Priority_Medium,
.DMA_FIFOMode = DMA_FIFOMode_Disable,
.DMA_FIFOThreshold = DMA_FIFOThreshold_Full,
.DMA_MemoryBurst = DMA_MemoryBurst_Single,
.DMA_PeripheralBurst = DMA_PeripheralBurst_Single,
},
},
},
.sclk = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Speed = GPIO_Speed_100MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.miso = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.mosi = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_12,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
.slave_count = 1,
.ssel = { {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_15,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
} },
};
uint32_t pios_overo_id = 0;
void PIOS_OVERO_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_OVERO_DMA_irq_handler(pios_overo_id);
}
#else
#endif /* PIOS_OVERO_SPI */
#include <pios_usart_priv.h>
#ifdef PIOS_INCLUDE_COM_TELEM
/*
* Telemetry on main USART
*/
static const struct pios_usart_cfg pios_usart_telem_cfg = {
.regs = USART2,
.remap = GPIO_AF_USART2,
.init = {
.USART_BaudRate = 57600,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl =
USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx | USART_Mode_Tx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART2_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_5,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
#endif /* PIOS_COM_TELEM */
#ifdef PIOS_INCLUDE_GPS
/*
* GPS USART
*/
static const struct pios_usart_cfg pios_usart_gps_cfg = {
.regs = USART1,
.remap = GPIO_AF_USART1,
.init = {
.USART_BaudRate = 57600,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl =
USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx | USART_Mode_Tx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART1_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_9,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
#endif /* PIOS_INCLUDE_GPS */
#ifdef PIOS_INCLUDE_COM_AUX
/*
* AUX USART (UART label on rev2)
*/
static const struct pios_usart_cfg pios_usart_aux_cfg = {
.regs = USART6,
.remap = GPIO_AF_USART6,
.init = {
.USART_BaudRate = 57600,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl =
USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx | USART_Mode_Tx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART6_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
#endif /* PIOS_COM_AUX */
#ifdef PIOS_INCLUDE_COM_AUXSBUS
/*
* AUX USART SBUS ( UART/ S Bus label on rev2)
*/
static const struct pios_usart_cfg pios_usart_auxsbus_cfg = {
.regs = UART4,
.remap = GPIO_AF_UART4,
.init = {
.USART_BaudRate = 57600,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl =
USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx | USART_Mode_Tx,
},
.irq = {
.init = {
.NVIC_IRQChannel = UART4_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_1,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_0,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
#endif /* PIOS_INCLUDE_COM_AUXSBUS */
#ifdef PIOS_INCLUDE_COM_FLEXI
/*
* FLEXI PORT
*/
static const struct pios_usart_cfg pios_usart_flexi_cfg = {
.regs = USART3,
.remap = GPIO_AF_USART3,
.init = {
.USART_BaudRate = 57600,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl =
USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx | USART_Mode_Tx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART3_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
#endif /* PIOS_INCLUDE_COM_FLEXI */
#if defined(PIOS_INCLUDE_DSM)
/*
* Spektrum/JR DSM USART
*/
#include <pios_dsm_priv.h>
static const struct pios_usart_cfg pios_usart_dsm_aux_cfg = {
.regs = USART6,
.remap = GPIO_AF_USART6,
.init = {
.USART_BaudRate = 115200,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl = USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART6_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
static const struct pios_dsm_cfg pios_dsm_aux_cfg = {
.bind = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
};
static const struct pios_usart_cfg pios_usart_dsm_auxsbus_cfg = {
.regs = UART4,
.remap = GPIO_AF_UART4,
.init = {
.USART_BaudRate = 115200,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl = USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx,
},
.irq = {
.init = {
.NVIC_IRQChannel = UART4_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_1,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_0,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
static const struct pios_dsm_cfg pios_dsm_auxsbus_cfg = {
.bind = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_1,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
};
static const struct pios_usart_cfg pios_usart_dsm_flexi_cfg = {
.regs = USART3,
.remap = GPIO_AF_USART3,
.init = {
.USART_BaudRate = 115200,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl = USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART3_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
static const struct pios_dsm_cfg pios_dsm_flexi_cfg = {
.bind = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
};
#endif /* PIOS_INCLUDE_DSM */
#if defined(PIOS_INCLUDE_SBUS)
/*
* S.Bus USART
*/
#include <pios_sbus_priv.h>
static const struct pios_usart_cfg pios_usart_sbus_auxsbus_cfg = {
.regs = UART4,
.remap = GPIO_AF_UART4,
.init = {
.USART_BaudRate = 100000,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_Even,
.USART_StopBits = USART_StopBits_2,
.USART_HardwareFlowControl = USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx,
},
.irq = {
.init = {
.NVIC_IRQChannel = UART4_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_1,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_0,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_NOPULL
},
},
};
static const struct pios_sbus_cfg pios_sbus_cfg = {
/* Inverter configuration */
.inv = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_3,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_Speed = GPIO_Speed_2MHz,
},
},
.gpio_inv_enable = Bit_SET,
.gpio_inv_disable = Bit_RESET,
.gpio_clk_func = RCC_AHB1PeriphClockCmd,
.gpio_clk_periph = RCC_AHB1Periph_GPIOC,
};
#endif /* PIOS_INCLUDE_SBUS */
/*
* HK OSD
*/
static const struct pios_usart_cfg pios_usart_hkosd_auxsbus_cfg = {
.regs = UART4,
.remap = GPIO_AF_UART4,
.init = {
.USART_BaudRate = 57600,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl = USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx | USART_Mode_Tx,
},
.irq = {
.init = {
.NVIC_IRQChannel = UART4_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_1,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_0,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
static const struct pios_usart_cfg pios_usart_hkosd_aux_cfg = {
.regs = USART6,
.remap = GPIO_AF_USART6,
.init = {
.USART_BaudRate = 57600,
.USART_WordLength = USART_WordLength_8b,
.USART_Parity = USART_Parity_No,
.USART_StopBits = USART_StopBits_1,
.USART_HardwareFlowControl = USART_HardwareFlowControl_None,
.USART_Mode = USART_Mode_Rx | USART_Mode_Tx,
},
.irq = {
.init = {
.NVIC_IRQChannel = USART6_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
.tx = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
},
};
#if defined(PIOS_INCLUDE_COM)
#include <pios_com_priv.h>
#endif /* PIOS_INCLUDE_COM */
#if defined(PIOS_INCLUDE_I2C)
#include <pios_i2c_priv.h>
/*
* I2C Adapters
*/
void PIOS_I2C_mag_adapter_ev_irq_handler(void);
void PIOS_I2C_mag_adapter_er_irq_handler(void);
void I2C1_EV_IRQHandler()
__attribute__ ((alias("PIOS_I2C_mag_adapter_ev_irq_handler")));
void I2C1_ER_IRQHandler()
__attribute__ ((alias("PIOS_I2C_mag_adapter_er_irq_handler")));
static const struct pios_i2c_adapter_cfg pios_i2c_mag_adapter_cfg = {
.regs = I2C1,
.remap = GPIO_AF_I2C1,
.init = {
.I2C_Mode = I2C_Mode_I2C,
.I2C_OwnAddress1 = 0,
.I2C_Ack = I2C_Ack_Enable,
.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit,
.I2C_DutyCycle = I2C_DutyCycle_2,
.I2C_ClockSpeed = 400000, /* bits/s */
},
.transfer_timeout_ms = 50,
.scl = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.sda = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.event = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C1_EV_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.error = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C1_ER_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
uint32_t pios_i2c_mag_adapter_id;
void PIOS_I2C_mag_adapter_ev_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_EV_IRQ_Handler(pios_i2c_mag_adapter_id);
}
void PIOS_I2C_mag_adapter_er_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_ER_IRQ_Handler(pios_i2c_mag_adapter_id);
}
void PIOS_I2C_flexiport_adapter_ev_irq_handler(void);
void PIOS_I2C_flexiport_adapter_er_irq_handler(void);
void I2C2_EV_IRQHandler() __attribute__ ((alias ("PIOS_I2C_flexiport_adapter_ev_irq_handler")));
void I2C2_ER_IRQHandler() __attribute__ ((alias ("PIOS_I2C_flexiport_adapter_er_irq_handler")));
static const struct pios_i2c_adapter_cfg pios_i2c_flexiport_adapter_cfg = {
.regs = I2C2,
.remap = GPIO_AF_I2C2,
.init = {
.I2C_Mode = I2C_Mode_I2C,
.I2C_OwnAddress1 = 0,
.I2C_Ack = I2C_Ack_Enable,
.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit,
.I2C_DutyCycle = I2C_DutyCycle_2,
.I2C_ClockSpeed = 400000, /* bits/s */
},
.transfer_timeout_ms = 50,
.scl = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.sda = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.event = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C2_EV_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.error = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C2_ER_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
uint32_t pios_i2c_flexiport_adapter_id;
void PIOS_I2C_flexiport_adapter_ev_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_EV_IRQ_Handler(pios_i2c_flexiport_adapter_id);
}
void PIOS_I2C_flexiport_adapter_er_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_ER_IRQ_Handler(pios_i2c_flexiport_adapter_id);
}
void PIOS_I2C_pressure_adapter_ev_irq_handler(void);
void PIOS_I2C_pressure_adapter_er_irq_handler(void);
void I2C3_EV_IRQHandler() __attribute__ ((alias ("PIOS_I2C_pressure_adapter_ev_irq_handler")));
void I2C3_ER_IRQHandler() __attribute__ ((alias ("PIOS_I2C_pressure_adapter_er_irq_handler")));
static const struct pios_i2c_adapter_cfg pios_i2c_pressure_adapter_cfg = {
.regs = I2C3,
.remap = GPIO_AF_I2C3,
.init = {
.I2C_Mode = I2C_Mode_I2C,
.I2C_OwnAddress1 = 0,
.I2C_Ack = I2C_Ack_Enable,
.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit,
.I2C_DutyCycle = I2C_DutyCycle_2,
.I2C_ClockSpeed = 400000, /* bits/s */
},
.transfer_timeout_ms = 50,
.scl = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_8,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.sda = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_9,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_OType = GPIO_OType_OD,
.GPIO_PuPd = GPIO_PuPd_NOPULL,
},
},
.event = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C3_EV_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.error = {
.flags = 0, /* FIXME: check this */
.init = {
.NVIC_IRQChannel = I2C3_ER_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGHEST,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
uint32_t pios_i2c_pressure_adapter_id;
void PIOS_I2C_pressure_adapter_ev_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_EV_IRQ_Handler(pios_i2c_pressure_adapter_id);
}
void PIOS_I2C_pressure_adapter_er_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_I2C_ER_IRQ_Handler(pios_i2c_pressure_adapter_id);
}
#endif /* PIOS_INCLUDE_I2C */
#if defined(PIOS_INCLUDE_RTC)
/*
* Realtime Clock (RTC)
*/
#include <pios_rtc_priv.h>
void PIOS_RTC_IRQ_Handler (void);
void RTC_WKUP_IRQHandler() __attribute__ ((alias ("PIOS_RTC_IRQ_Handler")));
static const struct pios_rtc_cfg pios_rtc_main_cfg = {
.clksrc = RCC_RTCCLKSource_HSE_Div16, // Divide 8 Mhz crystal down to 1
// For some reason it's acting like crystal is 16 Mhz. This clock is then divided
// by another 16 to give a nominal 62.5 khz clock
.prescaler = 100, // Every 100 cycles gives 625 Hz
.irq = {
.init = {
.NVIC_IRQChannel = RTC_WKUP_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
void PIOS_RTC_IRQ_Handler (void)
{
PIOS_RTC_irq_handler ();
}
#endif
#include "pios_tim_priv.h"
static const TIM_TimeBaseInitTypeDef tim_2_3_5_time_base = {
.TIM_Prescaler = (PIOS_PERIPHERAL_APB1_CLOCK / 1000000) - 1,
.TIM_ClockDivision = TIM_CKD_DIV1,
.TIM_CounterMode = TIM_CounterMode_Up,
.TIM_Period = ((1000000 / PIOS_SERVO_UPDATE_HZ) - 1),
.TIM_RepetitionCounter = 0x0000,
};
static const TIM_TimeBaseInitTypeDef tim_9_10_11_time_base = {
.TIM_Prescaler = (PIOS_PERIPHERAL_APB2_CLOCK / 1000000) - 1,
.TIM_ClockDivision = TIM_CKD_DIV1,
.TIM_CounterMode = TIM_CounterMode_Up,
.TIM_Period = ((1000000 / PIOS_SERVO_UPDATE_HZ) - 1),
.TIM_RepetitionCounter = 0x0000,
};
// Set up timers that only have inputs on APB2
static const TIM_TimeBaseInitTypeDef tim_1_time_base = {
.TIM_Prescaler = (PIOS_PERIPHERAL_APB2_CLOCK / 1000000) - 1,
.TIM_ClockDivision = TIM_CKD_DIV1,
.TIM_CounterMode = TIM_CounterMode_Up,
.TIM_Period = 0xFFFF,
.TIM_RepetitionCounter = 0x0000,
};
static const TIM_TimeBaseInitTypeDef tim_8_time_base = {
.TIM_Prescaler = (PIOS_PERIPHERAL_APB2_CLOCK / 1000000) - 1,
.TIM_ClockDivision = TIM_CKD_DIV1,
.TIM_CounterMode = TIM_CounterMode_Up,
.TIM_Period = 0xFFFF,
.TIM_RepetitionCounter = 0x0000,
};
// Set up timers that only have inputs on APB1
static const TIM_TimeBaseInitTypeDef tim_4_time_base = {
.TIM_Prescaler = (PIOS_PERIPHERAL_APB1_CLOCK / 1000000) - 1,
.TIM_ClockDivision = TIM_CKD_DIV1,
.TIM_CounterMode = TIM_CounterMode_Up,
.TIM_Period = 0xFFFF,
.TIM_RepetitionCounter = 0x0000,
};
static const struct pios_tim_clock_cfg tim_2_cfg = {
.timer = TIM2,
.time_base_init = &tim_2_3_5_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM2_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_3_cfg = {
.timer = TIM3,
.time_base_init = &tim_2_3_5_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM3_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_5_cfg = {
.timer = TIM5,
.time_base_init = &tim_2_3_5_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM5_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_8_cfg = {
.timer = TIM8,
.time_base_init = &tim_8_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM8_CC_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_9_cfg = {
.timer = TIM9,
.time_base_init = &tim_9_10_11_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM1_BRK_TIM9_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_10_cfg = {
.timer = TIM10,
.time_base_init = &tim_9_10_11_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM1_UP_TIM10_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_11_cfg = {
.timer = TIM11,
.time_base_init = &tim_9_10_11_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM1_TRG_COM_TIM11_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_1_cfg = {
.timer = TIM1,
.time_base_init = &tim_1_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM1_CC_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
static const struct pios_tim_clock_cfg tim_4_cfg = {
.timer = TIM4,
.time_base_init = &tim_4_time_base,
.irq = {
.init = {
.NVIC_IRQChannel = TIM4_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_MID,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
};
/**
* Pios servo configuration structures
*/
#include <pios_servo_priv.h>
static const struct pios_tim_channel pios_tim_servoport_all_pins[] = {
{
.timer = TIM9,
.timer_chan = TIM_Channel_1,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_5,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource5,
},
.remap = GPIO_AF_TIM9,
},
{
.timer = TIM9,
.timer_chan = TIM_Channel_2,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource6,
},
.remap = GPIO_AF_TIM9,
},
{
.timer = TIM11,
.timer_chan = TIM_Channel_1,
.pin = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_9,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource9,
},
.remap = GPIO_AF_TIM11,
},
{
.timer = TIM10,
.timer_chan = TIM_Channel_1,
.pin = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_8,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource8,
},
.remap = GPIO_AF_TIM10,
},
{
.timer = TIM5,
.timer_chan = TIM_Channel_3,
.pin = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_2,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource2,
},
.remap = GPIO_AF_TIM5,
},
{
.timer = TIM5,
.timer_chan = TIM_Channel_4,
.pin = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_3,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource3,
},
.remap = GPIO_AF_TIM5,
},
{
.timer = TIM3,
.timer_chan = TIM_Channel_3,
.pin = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_0,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource0,
},
.remap = GPIO_AF_TIM3,
},
{
.timer = TIM3,
.timer_chan = TIM_Channel_4,
.pin = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_1,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource1,
},
.remap = GPIO_AF_TIM3,
},
// PB3 - TIM2 CH2 LED1
{
.timer = TIM2,
.timer_chan = TIM_Channel_2,
.pin = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_3,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource3,
},
.remap = GPIO_AF_TIM2,
},
// PB4 - TIM3 CH1 LED2
{
.timer = TIM3,
.timer_chan = TIM_Channel_1,
.pin = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_4,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource4,
},
.remap = GPIO_AF_TIM3,
},
};
const struct pios_servo_cfg pios_servo_cfg = {
.tim_oc_init = {
.TIM_OCMode = TIM_OCMode_PWM1,
.TIM_OutputState = TIM_OutputState_Enable,
.TIM_OutputNState = TIM_OutputNState_Disable,
.TIM_Pulse = PIOS_SERVOS_INITIAL_POSITION,
.TIM_OCPolarity = TIM_OCPolarity_High,
.TIM_OCNPolarity = TIM_OCPolarity_High,
.TIM_OCIdleState = TIM_OCIdleState_Reset,
.TIM_OCNIdleState = TIM_OCNIdleState_Reset,
},
.channels = pios_tim_servoport_all_pins,
.num_channels = NELEMENTS(pios_tim_servoport_all_pins),
};
/*
* PWM Inputs
*/
#if defined(PIOS_INCLUDE_PWM) || defined(PIOS_INCLUDE_PPM)
#include <pios_pwm_priv.h>
static const struct pios_tim_channel pios_tim_rcvrport_all_channels[] = {
{
.timer = TIM4,
.timer_chan = TIM_Channel_4,
.pin = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_15,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource15,
},
.remap = GPIO_AF_TIM4,
},
{
.timer = TIM4,
.timer_chan = TIM_Channel_3,
.pin = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_14,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource14,
},
.remap = GPIO_AF_TIM4,
},
{
.timer = TIM4,
.timer_chan = TIM_Channel_2,
.pin = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_13,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource13,
},
.remap = GPIO_AF_TIM4,
},
{
.timer = TIM4,
.timer_chan = TIM_Channel_1,
.pin = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_12,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource12,
},
.remap = GPIO_AF_TIM4,
},
{
.timer = TIM1,
.timer_chan = TIM_Channel_4,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_14,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource14,
},
.remap = GPIO_AF_TIM1,
},
{
.timer = TIM1,
.timer_chan = TIM_Channel_3,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_13,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource13,
},
.remap = GPIO_AF_TIM1,
},
{
.timer = TIM1,
.timer_chan = TIM_Channel_2,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource11,
},
.remap = GPIO_AF_TIM1,
},
{
.timer = TIM1,
.timer_chan = TIM_Channel_1,
.pin = {
.gpio = GPIOE,
.init = {
.GPIO_Pin = GPIO_Pin_9,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP
},
.pin_source = GPIO_PinSource9,
},
.remap = GPIO_AF_TIM1,
},
};
const struct pios_pwm_cfg pios_pwm_cfg = {
.tim_ic_init = {
.TIM_ICPolarity = TIM_ICPolarity_Rising,
.TIM_ICSelection = TIM_ICSelection_DirectTI,
.TIM_ICPrescaler = TIM_ICPSC_DIV1,
.TIM_ICFilter = 0x0,
},
.channels = pios_tim_rcvrport_all_channels,
.num_channels = NELEMENTS(pios_tim_rcvrport_all_channels),
};
#endif
/*
* PPM Input
*/
#if defined(PIOS_INCLUDE_PPM)
#include <pios_ppm_priv.h>
static const struct pios_ppm_cfg pios_ppm_cfg = {
.tim_ic_init = {
.TIM_ICPolarity = TIM_ICPolarity_Rising,
.TIM_ICSelection = TIM_ICSelection_DirectTI,
.TIM_ICPrescaler = TIM_ICPSC_DIV1,
.TIM_ICFilter = 0x0,
.TIM_Channel = TIM_Channel_2,
},
/* Use only the first channel for ppm */
.channels = &pios_tim_rcvrport_all_channels[0],
.num_channels = 1,
};
#endif //PPM
#if defined(PIOS_INCLUDE_GCSRCVR)
#include "pios_gcsrcvr_priv.h"
#endif /* PIOS_INCLUDE_GCSRCVR */
#if defined(PIOS_INCLUDE_RCVR)
#include "pios_rcvr_priv.h"
#endif /* PIOS_INCLUDE_RCVR */
/*
* SONAR Inputs
*/
#if defined(PIOS_INCLUDE_HCSR04)
#include <pios_hcsr04_priv.h>
static const struct pios_tim_channel pios_tim_hcsr04_port_all_channels[] = {
{
.timer = TIM8,
.timer_chan = TIM_Channel_3,
.pin = {
.gpio = GPIOC,
.init = {
.GPIO_Pin = GPIO_Pin_8,
.GPIO_Mode = GPIO_Mode_AF,
.GPIO_Speed = GPIO_Speed_2MHz,
.GPIO_PuPd = GPIO_PuPd_DOWN
},
.pin_source = GPIO_PinSource8,
},
.remap = GPIO_AF_TIM8,
},
};
const struct pios_hcsr04_cfg pios_hcsr04_cfg = {
.tim_ic_init = {
.TIM_ICPolarity = TIM_ICPolarity_Rising,
.TIM_ICSelection = TIM_ICSelection_DirectTI,
.TIM_ICPrescaler = TIM_ICPSC_DIV1,
.TIM_ICFilter = 0x0,
},
.channels = pios_tim_hcsr04_port_all_channels,
.num_channels = NELEMENTS(pios_tim_hcsr04_port_all_channels),
.trigger = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_10,
.GPIO_Mode = GPIO_Mode_OUT,
.GPIO_OType = GPIO_OType_PP,
.GPIO_PuPd = GPIO_PuPd_UP,
.GPIO_Speed = GPIO_Speed_2MHz,
},
},
};
#endif
#if defined(PIOS_INCLUDE_USB)
#include "pios_usb_priv.h"
static const struct pios_usb_cfg pios_usb_main_cfg = {
.irq = {
.init = {
.NVIC_IRQChannel = OTG_FS_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_LOW,
.NVIC_IRQChannelSubPriority = 3,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.vsense = {
.gpio = GPIOD,
.init = {
.GPIO_Pin = GPIO_Pin_11,
.GPIO_Speed = GPIO_Speed_25MHz,
.GPIO_Mode = GPIO_Mode_IN,
.GPIO_OType = GPIO_OType_OD,
},
}
};
#include "pios_usb_board_data_priv.h"
#include "pios_usb_desc_hid_cdc_priv.h"
#include "pios_usb_desc_hid_only_priv.h"
#include "pios_usbhook.h"
#endif /* PIOS_INCLUDE_USB */
#if defined(PIOS_INCLUDE_COM_MSG)
#include <pios_com_msg_priv.h>
#endif /* PIOS_INCLUDE_COM_MSG */
#if defined(PIOS_INCLUDE_USB_HID)
#include <pios_usb_hid_priv.h>
const struct pios_usb_hid_cfg pios_usb_hid_cfg = {
.data_if = 0,
.data_rx_ep = 1,
.data_tx_ep = 1,
};
#endif /* PIOS_INCLUDE_USB_HID */
#if defined(PIOS_INCLUDE_USB_CDC)
#include <pios_usb_cdc_priv.h>
const struct pios_usb_cdc_cfg pios_usb_cdc_cfg = {
.ctrl_if = 1,
.ctrl_tx_ep = 2,
.data_if = 2,
.data_rx_ep = 3,
.data_tx_ep = 3,
};
#endif /* PIOS_INCLUDE_USB_CDC */
Reference in New Issue View Git Blame Copy Permalink