BL images now always use hid-only.
FW images can use hid-only or hid+vcp but this is selected
ONLY at compile time based on whether PIOS_INCLUDE_USB_CDC
is defined.
CC uses HID+VCP by default now.
Now that we have a USB descriptor for HID+VCP that works
on Ubuntu 11.10, MacOS 10.7.3, Win7-SP1-32bit,
WinXP-SP3-32bit, Win7-SP1-64bit.
VCP is known to not work on WinXP without service pack 3.
The bootloader has been enabling pull-ups on all GPIO
pins during early init. These pull-ups are disabled
immediately before jumping to the firmware. This transition
results in all servos seeing a wide pulse as the board
resets making them jerk sideways aggresively and then snap
back to neutral.
All channels at max when using the FrSKY 4ch D4FR in PPM
mode results in the frame pulse shrinking well below our
threshold of 3800us and we lose frame.
With all 8 channels at max, the frame pulse becomes
indistinguishable from the other channels. Using all 8
channels with the FrSKY in PPM mode is NOT recommended
even after this change.
Recommend using at most 7 active channels in this mode so
we can still find the frame pulse.
The CC and PipX bootloader updater (BU) builds don't currently
work due to some recent changes in how LEDs are handled.
Remove them from the default BU targets so that the all_flight
target can build clean again.
Also fix a linker warning in OP build.
HID driver was incorrectly giving back the HID interface
descriptor when asked for the HID descriptor. This should
let OP boards interact better with generic HID layer drivers
and also gives us nicer output in lsusb once the HID descriptor
is read.
These new build targets will construct a flash image that
includes both a bootloader as well as a firmware image all
in one. Examples:
make ef_coptercontrol
make ef_revolution
This also adds support for a new target for writing this EF
image to boards that support a DFU interface (only F4-based
boards). This can be done by running:
make dfuutil_install
# Boot board with SBL asserted to activate STM32 DFU ROM
# Attach USB cable
make ef_revolution_dfu
Bootloader images are also now padded out to occupy the full
BL flash region.
for sensing and then load different config for CC and CC3D. Updated the
bootloader as well. Also changed the PIOS_USB_CheckAvailability function to
only return the sense signal and not the transfer_possible flag as this is not
set in time for the bootloader on CC3D for some reason.
The exti layer now allows drivers to register interrupt callbacks
during board initialization. All details of the driver using a
particular EXTI pin have been removed from the EXTI layer so it
can now be used on any board without board-specific modification.
This includes some nice refinements provided by Mike Smith during
initial review. His original commits have been squashed into this
one.
The main purpose of this new COM implementation is that it is
much simpler, and requires less code space. This takes a bit
of the pressure off of the CC bootloader which was right at
the limit of available code space in the bootloader partition.
This is not intended to ever be used by the application.
This driver also formalizes the assumptions in the bootloader's
usage of the COM layer. All messages are assumed to arrive
in atomic chunks from the HID layer.
These files do not contain content from the ID in the header.
This name seems to have been cut/pasted all over throughout
the openpilot source tree and should be removed from any files
that should not rightfully be attributed to this person.
Summary of changes:
* USB CDC and HID drivers are completely split apart.
* This will allow different max buffer sizes for HID and CDC.
* USB descriptors have been overhauled:
* Proper structs/macros/enums declared for USB (see pios_usb_defs.h)
* Two common descriptor definitions. One for HID+CDC another for HID only.
See pios_usb_desc_{hid_cdc,hid_only}.c for details.
* Long standing bugs in OP USB descriptors became much more obvious with the
new struct definitions.
* Board specific USB initialization is now in pios_usb_board_data.h in each build target.
* Definition of USB descriptors is now entirely indpendent of STM32 libs.
Glue into STM32 libs is provided by pios_usbhook.c.
* Removed a lot of stale/irrelevant USB #defines throughout the tree.
* Improved naming consistency throughout USB code:
* PIOS_USB_HID_* now refers to the HID endpoint code.
* PIOS_USB_CDC_* now refers to the CDC endpoint code.
* PIOS_USB_* now refers to the low-level USB code.
* PIOS_USB_BOARD_* now refers to board-specific USB data
* PIOS_USBHOOK_* is glue between PIOS and STM32 USB libs.
* struct usb_* and enum usb_* and USB_* and HID_* are all types from the USB spec.
* Shrunk the buffer size on the CDC call mgmt endpoint to save some RAM.
* Made a few more USB related variables static to save some RAM.
Reduced scope of many variables since they were being
exposed unnecessarily.
Renamed pios_usb_hid_prop code to pios_usbhook to reflect
the fact that it implements all of the callout functions
that are hooked into the stm32 usb library.
No code changes, just file, variable and define names are changed.
First, it better describes the serial protocol used by DSMx satellite
receivers. Second, many people using Spektrum radio, assume Spektrum
protocol. This is the attempt to address those inaccuracies.
