1
0
mirror of https://bitbucket.org/librepilot/librepilot.git synced 2024-12-05 13:24:11 +01:00
LibrePilot/flight/targets/boards/revolution/firmware/inc/FreeRTOSConfig.h
2014-03-09 16:08:27 +01:00

105 lines
4.4 KiB
C

#ifndef FREERTOS_CONFIG_H
#define FREERTOS_CONFIG_H
/*-----------------------------------------------------------
* Application specific definitions.
*
* These definitions should be adjusted for your particular hardware and
* application requirements.
*
* THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE
* FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE.
*
* See http://www.freertos.org/a00110.html.
*----------------------------------------------------------*/
/**
* @addtogroup PIOS PIOS
* @{
* @addtogroup FreeRTOS FreeRTOS
* @{
*/
/* Notes: We use 5 task priorities */
#define configCPU_CLOCK_HZ (SYSCLK_FREQ) // really the NVIC clock ...
#define configTICK_RATE_HZ ((portTickType)1000)
#define configMAX_PRIORITIES ((unsigned portBASE_TYPE)5)
#define configMINIMAL_STACK_SIZE ((unsigned short)512)
#define configTOTAL_HEAP_SIZE ((size_t)(180 * 1024)) // this is minimum, not total
#define configMAX_TASK_NAME_LEN (16)
#define configUSE_PREEMPTION 1
#define configUSE_IDLE_HOOK 1
#define configUSE_TICK_HOOK 0
#define configUSE_TRACE_FACILITY 0
#define configUSE_16_BIT_TICKS 0
#define configIDLE_SHOULD_YIELD 0
#define configUSE_MUTEXES 1
#define configUSE_RECURSIVE_MUTEXES 1
#define configUSE_COUNTING_SEMAPHORES 0
#define configUSE_ALTERNATIVE_API 0
#define configCHECK_FOR_STACK_OVERFLOW 2
#define configQUEUE_REGISTRY_SIZE 10
#define configUSE_TIMERS 1
#define configTIMER_TASK_PRIORITY (configMAX_PRIORITIES - 1) /* run timers at max priority */
#define configTIMER_QUEUE_LENGTH 10
#define configTIMER_TASK_STACK_DEPTH configMINIMAL_STACK_SIZE
/* Co-routine definitions. */
#define configUSE_CO_ROUTINES 0
#define configMAX_CO_ROUTINE_PRIORITIES (2)
/* Set the following definitions to 1 to include the API function, or zero
to exclude the API function. */
#define INCLUDE_vTaskPrioritySet 1
#define INCLUDE_uxTaskPriorityGet 1
#define INCLUDE_vTaskDelete 1
#define INCLUDE_vTaskCleanUpResources 1
#define INCLUDE_vTaskSuspend 1
#define INCLUDE_vTaskDelayUntil 1
#define INCLUDE_vTaskDelay 1
#define INCLUDE_xTaskGetSchedulerState 1
#define INCLUDE_xTaskGetCurrentTaskHandle 1
#define INCLUDE_uxTaskGetStackHighWaterMark 1
#define INCLUDE_xTaskGetIdleTaskHandle 1
/* This is the raw value as per the Cortex-M3 NVIC. Values can be 255
(lowest) to 1 (highest maskable) to 0 (highest non-maskable). */
#define configKERNEL_INTERRUPT_PRIORITY 15 << 4 /* equivalent to NVIC priority 15 */
#define configMAX_SYSCALL_INTERRUPT_PRIORITY 3 << 4 /* equivalent to NVIC priority 3 */
/* This is the value being used as per the ST library which permits 16
priority values, 0 to 15. This must correspond to the
configKERNEL_INTERRUPT_PRIORITY setting. Here 15 corresponds to the lowest
NVIC value of 255. */
#define configLIBRARY_KERNEL_INTERRUPT_PRIORITY 15
/* Enable run time stats collection */
#define configGENERATE_RUN_TIME_STATS 1
#define INCLUDE_uxTaskGetRunTime 1
/*
* Once we move to CMSIS2 we can at least use:
*
* CoreDebug->DEMCR |= CoreDebug_DEMCR_TRCENA_Msk;
*
* (still nothing for the DWT registers, surprisingly)
*/
#define portCONFIGURE_TIMER_FOR_RUN_TIME_STATS() \
do { \
(*(unsigned long *)0xe000edfc) |= (1 << 24); /* DEMCR |= DEMCR_TRCENA */ \
(*(unsigned long *)0xe0001000) |= 1; /* DWT_CTRL |= DWT_CYCCNT_ENA */ \
} \
while (0)
#define portGET_RUN_TIME_COUNTER_VALUE() (*(unsigned long *)0xe0001004) /* DWT_CYCCNT */
/**
* @}
*/
#endif /* FREERTOS_CONFIG_H */