1
0
mirror of https://bitbucket.org/librepilot/librepilot.git synced 2024-11-30 08:24:11 +01:00
LibrePilot/flight/OpenPilot/System/pios_board.c
stac 8d015a57d0 pios spi: support both master and slave configs
Added support for SPI slave configurations to the pios SPI layer.

Converted the board specific configuration for the PIOS SPI layer to
use const static initializers rather than #defines (see pios_board.c).

SPI interface between the OP board and the AHRS is now operational at
a basic level, capable of moving simple single byte messages between
boards.  Multi-byte, CRC protected messages will be added on top of this.

git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@759 ebee16cc-31ac-478f-84a7-5cbb03baadba
2010-06-13 04:23:44 +00:00

246 lines
7.4 KiB
C

/**
******************************************************************************
*
* @file pios_board.c
* @author The OpenPilot Team, http://www.openpilot.org Copyright (C) 2010.
* @brief Defines board specific static initializers for hardware for the OpenPilot board.
* @see The GNU Public License (GPL) Version 3
*
*****************************************************************************/
/*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <pios.h>
#include <pios_spi_priv.h>
/* MicroSD Interface
*
* NOTE: Leave this declared as const static data so that it ends up in the
* .rodata section (ie. Flash) rather than in the .bss section (RAM).
*/
void PIOS_SPI_sdcard_irq_handler(void);
const struct pios_spi_cfg pios_spi_sdcard_cfg = {
.regs = SPI1,
.init = {
.SPI_Mode = SPI_Mode_Master,
.SPI_Direction = SPI_Direction_2Lines_FullDuplex,
.SPI_DataSize = SPI_DataSize_8b,
.SPI_NSS = SPI_NSS_Soft,
.SPI_FirstBit = SPI_FirstBit_MSB,
.SPI_CRCPolynomial = 7,
.SPI_CPOL = SPI_CPOL_High,
.SPI_CPHA = SPI_CPHA_2Edge,
.SPI_BaudRatePrescaler = 7 << 3, /* Maximum divider (ie. slowest clock rate) */
},
.dma = {
.ahb_clk = RCC_AHBPeriph_DMA1,
.irq = {
.handler = PIOS_SPI_sdcard_irq_handler,
.flags = (DMA1_FLAG_TC2 | DMA1_FLAG_TE2 | DMA1_FLAG_HT2 | DMA1_FLAG_GL2),
.init = {
.NVIC_IRQChannel = DMA1_Channel2_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.channel = DMA1_Channel2,
.init = {
.DMA_PeripheralBaseAddr = (uint32_t)&(SPI1->DR),
.DMA_DIR = DMA_DIR_PeripheralSRC,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_M2M = DMA_M2M_Disable,
},
},
.tx = {
.channel = DMA1_Channel3,
.init = {
.DMA_PeripheralBaseAddr = (uint32_t)&(SPI1->DR),
.DMA_DIR = DMA_DIR_PeripheralDST,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_M2M = DMA_M2M_Disable,
},
},
},
.ssel = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_4,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_Out_PP,
},
},
.sclk = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_5,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF_PP,
},
},
.miso = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_6,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_IPU,
},
},
.mosi = {
.gpio = GPIOA,
.init = {
.GPIO_Pin = GPIO_Pin_7,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF_PP,
},
},
};
/* AHRS Interface
*
* NOTE: Leave this declared as const static data so that it ends up in the
* .rodata section (ie. Flash) rather than in the .bss section (RAM).
*/
void PIOS_SPI_ahrs_irq_handler(void);
const struct pios_spi_cfg pios_spi_ahrs_cfg = {
.regs = SPI2,
.init = {
.SPI_Mode = SPI_Mode_Master,
.SPI_Direction = SPI_Direction_2Lines_FullDuplex,
.SPI_DataSize = SPI_DataSize_8b,
.SPI_NSS = SPI_NSS_Soft,
.SPI_FirstBit = SPI_FirstBit_MSB,
.SPI_CRCPolynomial = 7,
.SPI_CPOL = SPI_CPOL_High,
.SPI_CPHA = SPI_CPHA_2Edge,
.SPI_BaudRatePrescaler = 7 << 3, /* Maximum divider (ie. slowest clock rate) */
},
.dma = {
.ahb_clk = RCC_AHBPeriph_DMA1,
.irq = {
.handler = PIOS_SPI_ahrs_irq_handler,
.flags = (DMA1_FLAG_TC4 | DMA1_FLAG_TE4 | DMA1_FLAG_HT4 | DMA1_FLAG_GL4),
.init = {
.NVIC_IRQChannel = DMA1_Channel4_IRQn,
.NVIC_IRQChannelPreemptionPriority = PIOS_IRQ_PRIO_HIGH,
.NVIC_IRQChannelSubPriority = 0,
.NVIC_IRQChannelCmd = ENABLE,
},
},
.rx = {
.channel = DMA1_Channel4,
.init = {
.DMA_PeripheralBaseAddr = (uint32_t)&(SPI2->DR),
.DMA_DIR = DMA_DIR_PeripheralSRC,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_M2M = DMA_M2M_Disable,
},
},
.tx = {
.channel = DMA1_Channel5,
.init = {
.DMA_PeripheralBaseAddr = (uint32_t)&(SPI2->DR),
.DMA_DIR = DMA_DIR_PeripheralDST,
.DMA_PeripheralInc = DMA_PeripheralInc_Disable,
.DMA_MemoryInc = DMA_MemoryInc_Enable,
.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte,
.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte,
.DMA_Mode = DMA_Mode_Normal,
.DMA_Priority = DMA_Priority_Medium,
.DMA_M2M = DMA_M2M_Disable,
},
},
},
.ssel = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_12,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_Out_PP,
},
},
.sclk = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_13,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF_PP,
},
},
.miso = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_14,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_IPU,
},
},
.mosi = {
.gpio = GPIOB,
.init = {
.GPIO_Pin = GPIO_Pin_15,
.GPIO_Speed = GPIO_Speed_50MHz,
.GPIO_Mode = GPIO_Mode_AF_PP,
},
},
};
/*
* Board specific number of devices.
*/
struct pios_spi_dev pios_spi_devs[] = {
{
.cfg = &pios_spi_sdcard_cfg,
},
{
.cfg = &pios_spi_ahrs_cfg,
},
};
uint8_t pios_spi_num_devices = NELEMENTS(pios_spi_devs);
void PIOS_SPI_sdcard_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_SPI_IRQ_Handler(PIOS_SDCARD_SPI);
}
void PIOS_SPI_ahrs_irq_handler(void)
{
/* Call into the generic code to handle the IRQ for this specific device */
PIOS_SPI_IRQ_Handler(PIOS_OPAHRS_SPI);
}