Both EVents and ERrors were mistakenly being mapped to the
EVent IRQ channel.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@659 ebee16cc-31ac-478f-84a7-5cbb03baadba
This commit fixes all existing warnings.
All basic compiler warnings will now be treated as errors.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@658 ebee16cc-31ac-478f-84a7-5cbb03baadba
This fixes the COM interface over USB HID to the point where
it can establish and maintain solid communications with the UAVObject
Browser in the GCS.
Tested only on Linux. The USB HID interface is still disabled for now
until it is tested successfully by a wider group.
Edit telemetry.c and set ALLOW_HID_TELEMETRY to 1 to enable telemetry
over the USB HID interface and report your results in the forum.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@656 ebee16cc-31ac-478f-84a7-5cbb03baadba
- New Attitude module for AHRS (skeleton)
- New AttitudeSettings UAVobject
- New AttitudeActual UAVobject
- Regenerated UAVobjects
- Added new UAVobjects to OpenPilot and GCS builds
- New PiOS driver for OpenPilot AHRS (stubs only)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@655 ebee16cc-31ac-478f-84a7-5cbb03baadba
This module reads from the BMP085 pressure sensor. It periodically
updates the pressure (kPa) and temperature (C) as well as the
calculated altitude (m).
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@640 ebee16cc-31ac-478f-84a7-5cbb03baadba
FreeRTOS has a strict requirement that even interrupt-safe API calls (ie.
those ending in "FromISR") can only be called from ISRs that are at lesser
or equal priorities to configMAX_SYSCALL_INTERRUPT_PRIORITY. See the
"configKERNEL_INTERRUPT_PRIORITY and configMAX_SYSCALL_INTERRUPT_PRIORITY"
section at:
http://www.freertos.org/a00110.html
The interrupt numbers used on the Cortex-M3 CPU has a somewhat backward
representation of the interrupt numbers so 255 = lowest priority and
0 = highest priority.
The calculation is further complicated by the STM32 implementation only using
the upper 4 bits of the priority value. Only 0x00, 0x10, 0x20, ..., 0xE0, 0xF0
represent useful interrupt priorities.
FreeRTOS requires that MAX_SYSCALL and KERNEL interrupt priorities are expressed
as raw unshifted 8-bit values to be programmed directly into the BASEPRI register.
The priority values passed to the NVIC initialization, however, are expected
to be 4-bit values and are shifted up by 4 within NVIC_Init() for you.
The end result is that we need this arrangement:
[highest priority]
NVIC_0 (Non-maskable-interrupt)
NVIC_1
NVIC_2
[Must NOT call FreeRTOS APIs above here]
configMAX_SYSCALL_INTERRUPT_PRIORITY (now at 48 = 0x30 = NVIC_3)
PIOS_IRQ_PRIO_HIGHEST (cur. NVIC_4)
PIOS_IRQ_PRIO_HIGH (cur. NVIC_5)
PIOS_IRQ_PRIO_MID (cur. NVIC_8)
PIOS_IRQ_PRIO_LOW (cur. NVIC_12)
configKERNEL_INTERRUPT_PRIORITY (240 = 0xF0 = NVIC_15)
[lowest priority]
The previous config had configMAX_SYSCALL_INTERRUPT_PRIORITY set at
191 (0xBF) which is effectively NVIC_11. This was allowing all of
the MID, HIGH and HIGHEST interrupt handlers to preempt the OS in
its critical sections. Since some of these ISRs were calling
FreeRTOS APIs, this would result in corrupting internal data structures
within the OS.
It should be ok to move the configKERNEL_INTERRUPT_PRIORITY to a higher
priority as long as it is less than configMAX_SYSCALL_INTERRUPT_PRIORITY.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@637 ebee16cc-31ac-478f-84a7-5cbb03baadba
Commit @583 uncomments the HIDTest task creation. HIDTest task is configured to run at
priority 4 (== tskIDLE_PRIORITY + 4) which is higher priority than the "System" task at
priority 3 (== tskIDLE_PRIORITY + 3).
The HIDTest task never blocks so it prevents the system task (and any other task of priority
less than 4) from ever running.
This commit does not fix the root problem of HIDTest never blocking, but rather lowers
its priority to be equal to the system task so that they share the CPU. This is a
temporary workaround.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@586 ebee16cc-31ac-478f-84a7-5cbb03baadba
