Bootloader updaters were all broken due to recent
changes in LED configuration handling. Removing
LED support from the BU loads allows them to build
again, but they provide no feedback about when they're
finished writing flash.
The code in RCC_GetClocksFreq() uses HSE_VALUE to determine
the tick rate of the SYSCLK. This in turn is used by the
code in PIOS_DELAY_* to compute delays.
ST Library defaults this to 25MHz for the F4. Our board
actually has an 8MHz oscillator so delays were way off.
Mostly affects the bootloaders since most FW code uses RTOS
delays rather than busy-waiting using PIOS_DELAY_*.
Removes hard-coding of JTAG interface config in the
<board>_program make macros.
This allows the use of STLINKv2 for F4 boards while
continuing to use the FOSS JTAG revB on F1 boards.
for sensing and then load different config for CC and CC3D. Updated the
bootloader as well. Also changed the PIOS_USB_CheckAvailability function to
only return the sense signal and not the transfer_possible flag as this is not
set in time for the bootloader on CC3D for some reason.
Board specific HW configuration is now collected in a single .c
file for each board. This HW configuration is #include'd into
the FW, BL and BU builds for each board.
These new .c files are found in:
flight/board_hw_defs/<board_name>/board_hw_defs.c
Parts of this information were previously duplicated between
the BL and FW builds. This commit cleans up the duplication.
Using a #include on a .c file is a bit ugly but it allows us
to ensure that all of the symbols in the board_hw_defs.c file
are *ONLY* used in the PIOS_Board_Init() function for each
software build.
The main purpose of this new COM implementation is that it is
much simpler, and requires less code space. This takes a bit
of the pressure off of the CC bootloader which was right at
the limit of available code space in the bootloader partition.
This is not intended to ever be used by the application.
This driver also formalizes the assumptions in the bootloader's
usage of the COM layer. All messages are assumed to arrive
in atomic chunks from the HID layer.
This can be used by the GCS firmware uploader widget to boot
the firmware with a (temporarily) defaulted hwsettings uavo
so that a user can easily recover from a bad/incompatible
hwsettings configuration without wiping all settings.
This uses the same mechanism that the BootFault auto-recovery
code already uses in the CC firmware. The auto-recovery is
triggered by setting the failed-boot counter to a maximum
value forcing recovery on the next FW init.
The PIOS_COM_ReceiveBufferUsed() function call is no longer
necessary since the same semantics can be achieved using calls
to PIOS_COM_ReceiveBuffer().
Summary of changes:
* USB CDC and HID drivers are completely split apart.
* This will allow different max buffer sizes for HID and CDC.
* USB descriptors have been overhauled:
* Proper structs/macros/enums declared for USB (see pios_usb_defs.h)
* Two common descriptor definitions. One for HID+CDC another for HID only.
See pios_usb_desc_{hid_cdc,hid_only}.c for details.
* Long standing bugs in OP USB descriptors became much more obvious with the
new struct definitions.
* Board specific USB initialization is now in pios_usb_board_data.h in each build target.
* Definition of USB descriptors is now entirely indpendent of STM32 libs.
Glue into STM32 libs is provided by pios_usbhook.c.
* Removed a lot of stale/irrelevant USB #defines throughout the tree.
* Improved naming consistency throughout USB code:
* PIOS_USB_HID_* now refers to the HID endpoint code.
* PIOS_USB_CDC_* now refers to the CDC endpoint code.
* PIOS_USB_* now refers to the low-level USB code.
* PIOS_USB_BOARD_* now refers to board-specific USB data
* PIOS_USBHOOK_* is glue between PIOS and STM32 USB libs.
* struct usb_* and enum usb_* and USB_* and HID_* are all types from the USB spec.
* Shrunk the buffer size on the CDC call mgmt endpoint to save some RAM.
* Made a few more USB related variables static to save some RAM.
Reduced scope of many variables since they were being
exposed unnecessarily.
Renamed pios_usb_hid_prop code to pios_usbhook to reflect
the fact that it implements all of the callout functions
that are hooked into the stm32 usb library.
