This patch is based on work of Crubier (LPF) and Cossacs (AxisLock mode).
I've just reworked it a bit by adding a dynamic memory allocation for
static module data.
This module and its associated settings uavo can be used
to test various fault conditions during initialization.
To enable the module, add the TEST_FAULTS=YES to your make
command line:
make fw_coptercontrol TEST_FAULTS=YES
Once this module is part of your firmware load, you can
enable it in the hwsettings uavo and then select the
type of fault to insert by editing the faultsettings uavo.
On the next reset, the configured fault will be inserted
into the init sequence to allow you to test the boot fault
recovery code.
With a fault inserted, you should see 3 failed boot attempts
followed by a successful (recovery) boot. You will see the
BootFault alarm set to Critical, and the RAM version of your
hwsettings will be reset to defaults. Since the defaults have
all optional modules disabled, the fault module will be out of
the way during the recovery boot.
You can then "Load" the flash version of the hwsettings uavo
in the object browser, disable the Fault module and then "Save"
the hwsettings module back to the board. The next reset will
boot normally without the fault inserted.
After 3 failed warm start attempts, the init sequence
will force the RAM version of the HWSettings object
to its defaults. This should allow a user to regain
connectivity to a board that is continually faulting
during init.
This is accomplished by:
- Incrementing a boot counter that is stored in the
STM32 BKP registers. These registers survive a
warm start but are cleared on a cold start (ie. powerup).
- On multiple failures, force hwsettings to defaults
and raise the (new) BootFault alarm to prevent arming.
- Resetting the boot counter whenever the system manages
to successfully run the System Module task.
NOTE: This does not actually change the hwsettings object in
flash. That's up to the user.
This is intended to catch ONLY faults during early initialization.
It should not be used to recover from faults after the application
is up and running.
This allows the HID and VCP functions to be configured
separately so that additional functions can be more easily
bound to the VCP port.
This change also provides a safety net that forces either
the HID or VCP to be configured for USB Telemetry. This
safety net may vanish in the future once the GCS can check
it. Disabling USB Telemetry entirely would save more than
400 bytes of RAM.
- both CC serial ports are now disabled by default (no telemetry);
- serial ports now have DSM2, DSMX (10bit) and DSMX (11bit) options;
- ReceiverGroups now have DSM (MainPort) and DSM (FlexiPort) options.
For DSM2 protocol there is an explicit resolution bit in the stream, so
the DSM2 should be selected. For DSMX there is no such bit, and user
should choose the resolution from the list configuring the spektrum port.
ReceiverGroups have single DSM option which is handled by the same driver.
Downside: this implementation saves received frame first, unrolls by the
end of frame. This should be ok, but may be improved by unrolling channels
on the fly in the rx callback.
Another minor difference is that a ChannelGroup is now bound to port:
DSM (MainPort) or DSM (FlexiPort). This was considered as acceptable
solution in order to not have 6 DSM options for each ChannelGroup and
even more in case of new DSM protocol variations.
Known problem: it is not possible to choose same protocols like
DSM2/DSM2 for two ports. It can be enabled by adding an exception to
common rule, though.
The DSMX throttle channel misbehavior (zero value) is not treated
specially yet. It should trigger the failsafe being out of bounds.
More info and data dumps are required to handle this properly.
PPM. This saves resources. Good suggestion Os. In this configuration we
could allow 12 channels of output but for now I'll leave it capped at 10 to
lessen resources on the mixer table.
With spektrum and camera stab enabled there was
1632 bytes heap remaining
180 bytes irq stack remaining
TelemetrySettings object removed (saved 200+ bytes of RAM). Telemetry
port speed moved to the HwSettings object. Added GPS port speed setting.
GCS code updated to reflect changes and support both fields.
