1
0
mirror of https://bitbucket.org/librepilot/librepilot.git synced 2024-12-11 19:24:10 +01:00
Commit Graph

47 Commits

Author SHA1 Message Date
James Cotton
836e34a483 Change revo sensors to update at 500 Hz and make sure in all cases it waits for
the relevant queue to provide data.  Also disable the quaternion stabilization
flag.
2012-05-12 13:12:56 -05:00
James Cotton
6c0dc80978 Shuffle more stack sizes around 2012-05-05 11:33:47 -05:00
James Cotton
85852df00b Make simulation produce data asynchronously for testing and add random accel
bias
2012-04-15 11:51:42 -05:00
James Cotton
9a2e0b071c Revert "Allow simulated quadcopter to include GyroBias in the artificial sensor data."
This reverts commit 212a10bcd4.
2012-04-14 17:20:01 -05:00
James Cotton
212a10bcd4 Allow simulated quadcopter to include GyroBias in the artificial sensor data. 2012-04-14 14:52:56 -05:00
James Cotton
a86e75bc99 Merge branch 'revolution' into sim 2012-04-14 14:12:03 -05:00
James Cotton
b7c3b1fdd1 Make the simulation provide GPSVelocity object since this is critical for EKF
now
2012-04-14 14:01:42 -05:00
James Cotton
b0ef456ccb Kickstart MPU6000 if there is no data 2012-04-13 20:29:41 -05:00
James Cotton
a0d1b00ade Cover an edge condition for the MPU6000 IRQ not firing 2012-04-13 19:37:30 -05:00
James Cotton
3071f77d59 Add Baro offset to the simulation 2012-04-03 10:58:48 -05:00
James Cotton
c988685293 Simulate GPS noise drift 2012-04-03 09:17:55 -05:00
James Cotton
5d0e513678 Fix small deg/rad issue in generating gps data 2012-04-03 09:17:55 -05:00
James Cotton
df6bc4deff Enable guidance on simulation and add wind model 2012-04-03 09:16:31 -05:00
James Cotton
ca535c2632 Fix bugs in simulated sensor data. Now works well with INSGPS. 2012-04-03 09:16:31 -05:00
James Cotton
84040d25b4 Add attitudesimulated object to capture the simulated state 2012-04-03 09:16:30 -05:00
James Cotton
543500ed78 Improve the simulated sensors to produce (I think) consistent data now 2012-04-03 09:16:30 -05:00
James Cotton
fbd8695d7d Check in WIP for osx simulation 2012-04-03 09:16:30 -05:00
James Cotton
28cab678ce Simulate a more complete QC model. 2012-04-03 09:16:28 -05:00
James Cotton
f1aa3b658e Add a new sensor simulation mode that essentially has a gyro rate that is rate
desired and the accel based on the current attitude.
2012-04-03 09:16:28 -05:00
James Cotton
6adc74f6f9 Check in the fake sensor data module 2012-04-03 09:16:27 -05:00
James Cotton
e82323af32 Make revolution work with the FreeRTOS queue based MPU6000 driver 2012-04-03 03:41:52 -05:00
Corvus Corax
0742c88a98 enabled optional rtation of Revolution board 2012-03-26 05:25:52 +02:00
Corvus Corax
d32dd0ccd4 Fixed fmod() versus fmodf() usage in flight/... 2012-03-26 04:16:54 +02:00
James Cotton
2f8049e20a Update the bootloader hw version for the mpu6000 board and make the sensor code
and initialization respond appropriately.  Enable hte L3GD20 and BMA180.
Let the board type determine which is used.
2012-03-22 00:41:37 -05:00
James Cotton
a77a859e5c Using some config switches to get this board up and running 2012-03-21 00:48:31 -05:00
James Cotton
7961aba83c Clean up a few more compiler warnings
Conflicts:

	flight/PiOS/Common/pios_ms5611.c
2012-03-03 13:32:56 -06:00
James Cotton
91a226fc12 Sometimes the mag stops updating so kickstart it 2012-03-03 13:31:46 -06:00
James Cotton
a778c45d6f For L3GD20 sensor task run at the sensor speed 2012-01-28 10:11:30 -06:00
James Cotton
13447ac907 Fix the MPU6000 implementation 2012-01-28 00:21:58 -06:00
James Cotton
b4435d0b35 For L3GD20 sensor task on revo update gyro once per physical sample 2012-01-26 23:29:12 -06:00
James Cotton
e4df3202e0 L3GD20: Update sensor task for revo to use the new queue 2012-01-25 22:50:19 -06:00
James Cotton
205aabe895 L3GD20: Make this sensor push data onto a FreeRTOS queue so that the sensor
reading task can block according.  Also now the gyro data is sent to
stabilization multiple times per update of the attitude loop.
2012-01-25 01:20:07 -06:00
James Cotton
f8e59443b8 If the BMA180 isn't read when an IRQ fires (because the flash chip has claimed
the bus) then it won't fire another interrupt until read.  For now this is
dealt with in the sensor loop by forcing a read when the fifo is empty.
2012-01-21 10:13:46 -06:00
James Cotton
6d72678086 Add timeout in the sensor task for reading sensors to stop the watchdog firing.
All sensors should later be converted to use FreeRTOS queues.
2012-01-21 08:32:41 -06:00
James Cotton
ce2d0fcbb1 L3GD20 data now running through IRQ -> FIFO 2012-01-17 19:36:32 -06:00
James Cotton
35025303cd Getting data from gyro. 2012-01-17 19:29:38 -06:00
James Cotton
cc47520baa Checking ID on ST gyro works 2012-01-04 23:23:42 -06:00
James Cotton
0fbcf7723d Code to disable all gyros. All modules now running. 2012-01-04 22:37:15 -06:00
James Cotton
0cc18e7dcf Add files for new L3DG20 sensor 2012-01-04 20:33:54 -06:00
James Cotton
25dfb5463e Add option to switch to using the MPU6000 accel instead of BMA180. Disabled by
default.
2011-12-29 02:08:13 -06:00
James Cotton
bf98630851 Add streaming the sensor data out of the serial port 2011-12-26 17:52:45 -06:00
James Cotton
9bf06bbd3e Force the loading of the sensor gains and biases at the beginning 2011-12-24 16:14:28 -06:00
James Cotton
1092ac3184 Use the scale and bias terms for hte mag and accel 2011-12-24 15:58:12 -06:00
James Cotton
dd89d232ba Add a magnetometer bias term although currently hardcoded to my board 2011-12-15 00:57:19 -06:00
James Cotton
2240ad924a Fix the orientation of the magnetometer 2011-12-15 00:46:43 -06:00
James Cotton
9148bb2c65 Make sure the sensors module grabs the sesor biases initially. 2011-12-14 10:38:43 -06:00
James Cotton
a37a17a4fb Created a separate Sensor module and Attitude module for revolution 2011-12-12 21:40:39 -06:00