Also reduce heap has it does not fit in SRAM anymore (not with current compiler).
(that's ok since if there is more space available, it will be reclaimed).
Merge branch 'master' into OP-423_Mathieu_Change_Init_To_Reduce_Memory_Footprint
Conflicts:
flight/CopterControl/System/inc/pios_config.h
flight/Modules/ManualControl/manualcontrol.c
This is a port of a work-in-progress by Sambas onto
the new driver infrastructure needed for boot-time
configuration.
PPM and PWM still don't coexist in a build but this
is closer.
The initial baud rates of each interface are now forced in the
board init code.
Any modules using USARTs should have fields added to
their settings object to allow the user to change the
baud rate from the default by using the COM layer APIs.
Developers requiring custom baud rates before the settings
objects are in place should locally edit the cfg structs
to specify the desired baud rates.
Tested this heap2 at runtime with CC and new compiler since old one (current) triggers strict alliasing error.
That's ok since strict aliasing is disabled on OP, and CC only use heap1.
This should mark an end to the compile-time selection of HW
configurations.
Minor changes in board initialization for all platforms:
- Most config structs are marked static to prevent badly written
drivers from directly referring to config data.
- Adapt to changes in .irq fields in config data.
- Adapt to changes in USART IRQ handling.
Major changes in board initialization for CC:
- Use HwSettings UAVObj to decide which drivers to attach to
the "main" port and the flexi port, and select the appropriate
device configuration data.
- HwSettings allows choosing between Disabled, Telemetry, SBUS,
Spektrum,GPS, and I2C for each of the two ports.
- Use ManualControlSettings.InputMode to init/configure the
appropriate receiver module, and register its available rx channels
with the PIOS_RCVR layer. Can choose between PWM, Spektrum and PPM
at board init time. PPM driver is broken, and SBUS will work once
it is added to this UAVObj as an option.
- CC build now includes code for SBUS, Spektrum and PWM receivers in
every firmware image.
PIOS_USART driver:
- Now handles its own low-level IRQs internally
- If NULL upper-level IRQ handler is bound in at board init time
then rx/tx is satisfied by internal PIOS_USART buffered IO routines
which are (typically) attached to the COM layer.
- If an alternate upper-level IRQ handler is bound in at board init
then that handler is called and expected to clear down the USART
IRQ sources. This is used by Spektrum and SBUS drivers.
PIOS_SBUS and PIOS_SPEKTRUM drivers:
- Improved data/API hiding
- No longer assume they know where their config data is stored which
allows for boot-time alternate configurations for the driver.
- Now registers an upper-level IRQ handlerwith the USART layer to
decouple the driver from which USART it is actually attached to.
This separates the RTC device and interrupt handling
from the devices that rely on the tick notifications.
Drivers can now register tick notification functions
that will be called on each RTC tick event.
All receivers now fall under the same driver API provided
by pios_rcvr.c.
This is part of a larger sequence of commits that will
switch the receiver selection over to boot time dynamic
configuration via UAVObjects.
The FreeRTOS IDLE task was using 512 bytes of stack.
The UAVObject Event task was also using 512 bytes of stack.
Both have been reduced, recovering 400+ bytes of heap.
Also implement some ordering (quite ugly still) in the module init and task creation order so we can decide which module to start/init first
and which module to start/init last.
This will be replaced/adapter with the uavobject list later (once it's implemented).
reserving some space for module init and task create parameters to customize module/task creation (this will be usefull once we get the list and customization from customer).
Changes have been made for OP and CC. Tested comped with CC,OP, sim_posix.
Only ran on bench with CC for couple of minutes (code increase expected but no dropping of stack which is good).
This gives task creation at the time wherethe all heap is available.
For CopterControl the following make options are available:
USE_TELEMETRY=[YES|NO|1|3] (default is YES, USART1)
USE_GPS=[YES|NO|1|3] (default is NO, USART3)
USE_SPEKTRUM=[YES|NO|1|3] (default is NO, USART3)
USE_SBUS=[YES|NO|1] (default is NO, USART1 only)
heap reamining is low (about 500) but stacks can be ajusted (specially the 200 bytes from system) to give the level close to 1Ko if needed.
Merge branch 'master' into OP-423_Mathieu_Change_Init_To_Reduce_Memory_Footprint
Conflicts:
flight/CopterControl/System/inc/FreeRTOSConfig.h
flight/CopterControl/System/inc/pios_config.h
- create linker section for those <module>Initialize()
- later this list will incorporate parameters as well. (this probably will be more a OP feature to swap/remove/delete module on the fly.
- this is not done at compile time anymore by Makefile.
- this will allow us to have control on the module start at run-time (not implemented but build the ground for it).
- this simplify the startup (Part of code re-org).
- this change does not affect sim_posix and win32 (since they don't need that)
- ensure it's compiling for PiOS.posix
- port to PiOS.win32 but not tested (not compiled)
- tested on CC
- compile on OP.
- this free ~200 bytes.
- current avalable bytes (is we keep the same remaining bytes on the stack than before) is easily passed the 1.2Ko mark on CC with new gcc (4.5.2)
- this does not include init-reorg for each module (I still think more can be freed)
It was tested being merged with OP-472_CorvusCorax_CopterControl-Guidance_v3
branch, Spektrum on USART3 and GPS on USART1 and seems to work.
Currently defaults mimic original behavior, that is, if USE_SPEKTRUM
is not defined - define USE_PWM and USE_GPS. Thsi should be refactored
later to make it configurable from the Makefile.
Also it was not ported to the OP MB: it currently does not support the
S.Bus hardware and still has original behavior with the patch. But this
is one more step to dynamic configuration of ports.
TODO: This should be dynamic in the future.
But for now define any compatile combination of:
USE_I2C (shared with USART3)
USE_TELEMETRY
USE_GPS
USE_SPEKTRUM
USE_SBUS (USART1 only, it needs an invertor)
and optionally define PIOS_PORT_* to USART port numbers
Defaults are:
#define PIOS_PORT_TELEMETRY 1
#define PIOS_PORT_GPS 3
#define PIOS_PORT_SPEKTRUM 3
#define PIOS_PORT_SBUS 1
#define USE_TELEMETRY
#define USE_GPS
Telemetry, GPS and PWM input are enabled by default.
