Issues were related to missing usb detection and broken communication while updloading fw.
They are now skipped in NON FreeRTOS mode (aka bootloader).
+review OPReview
The ST USB code will automatically receive on any
endpoint that is opened but not in the NAK state.
Make sure we set OUT endpoints to NAK initially.
It also happily writes via a NULL pointer in ep->xfer_buff
which writes to address 0x0000_0000. Since address
0x0 is aliased onto the internal flash by the BOOT0/1 pins
and the internal flash is (normally) in the LOCKED state,
this write puts the internal flash into an errored state.
This errored state means that writes to internal flash
are no longer allowed and all further writes fail.
The ST USB code will automatically receive on any
endpoint that is opened but not in the NAK state.
Make sure we set OUT endpoints to NAK initially.
It also happily writes via a NULL pointer in ep->xfer_buff
which writes to address 0x0000_0000. Since address
0x0 is aliased onto the internal flash by the BOOT0/1 pins
and the internal flash is (normally) in the LOCKED state,
this write puts the internal flash into an errored state.
This errored state means that writes to internal flash
are no longer allowed and all further writes fail.
USB CDC uses BULK endpoints to send/receive data. Typically,
a USB host will enqueue large buffers on its IN (device-to-host)
URBs. These buffers are larger than the max packet size for the
bulk endpoint.
The USB standard requires that an IN transfer ends when one of
these is true:
* a short packet (ie. less than max packet size) is sent by the
device
* a zero length packet (ZLP)
* enough packets that the entire host buffer is filled
Our device implementation never sends ZLPs. We sometimes send
packets that are exactly max-packet-size bytes long. This would
result in partially filling a host buffer without signalling (via
ZLP) that the transmission had finished. The host would then wait
until the next transfer had taken place before processing the first
data, thus delaying the first data.
This change simply forces all of our transfers to be short packets
and avoids the need to worry about zero length packets. This is
at the cost of some efficiency on the host side since its large
buffers will only ever be partially filled.
Conflicts:
flight/PiOS/STM32F30x/pios_usb_cdc.c
This code was previously passing a pointer to stack
data into PIOS_USBHOOK_CtrlTx() which may be sending
this data asynchronously. Now pass a pointer to
static data so that the asynchronous send doesn't
tx random stack contents.
This code was mistakenly tracking the IN (device-to-host)
requests with data stages. It should have been tracking
the OUT (host-to-device) requests with data stages.
This tracking data is important now that CDC is supported.
CDC actually uses OUT requests with data stages whereas HID
does not. This bug only triggered once CDC was enabled.
CDC and USART device drivers were not all clearing their
device structs before using them.
This specifically caused crashes in the case where the upper
COM layer was binding only a Tx path. The Rx path callback
in the lower driver was uninitialized random data and would
result in the lower driver faulting when it tried to call the
callback.
Conflicts:
flight/PiOS/STM32F30x/pios_usart.c
flight/PiOS/STM32F30x/pios_usb_cdc.c
flight/PiOS/STM32F30x/pios_usb_hid.c
The CDC layer on F1, F3 and F4 now always acts like an
infinte data sink whenever *either* there is no DTE present
(ie. no terminal program listening) *or* the USB cable is
disconnected.
F1 and F4 were previously checking the cable but not the DTE.
F3 didn't check anything. The COM layer didn't even ask the
lower layers.
All of this used to mean that any time a caller did a blocking
send to a CDC device without a DTE, it would eventually block
for up to a 5s timeout waiting for space in the Tx buffer.
Conflicts:
flight/PiOS/STM32F30x/pios_usb_cdc.c
The req parameter is passed to the OUT stage as a convenience.
Since the OUT callback is called *after* the transfer has occurred,
modifying the req would have absolutely no effect. Marking this
as const makes this expectation clear.
***** PLEASE NOTE ***** From this revision all F4 based boards (Revolution/OSD) needs bootloader version 5 to boot properly
Conflicts:
flight/pios/stm32f4xx/libraries/CMSIS2/Device/ST/STM32F4xx/Source/osd/system_stm32f4xx.c
flight/targets/boards/osd/board-info.mk
make/boot-defs.mk
make/common-defs.mk
This move and rework also breaks the dependency of the task monitor on the UAVO subsystem,
and pushes the responsibility for updating the TaskInfo UAVO into the System module.
+review OPReview
Also fixes warnings (and bugs) in F4 STM32_USB_OTG_Driver code, allowing -Werror to be enabled for all flight code.
Fixes all other compiler warnings that would otherwise cause the flight code to not compile with -Werror enabled.
Along the way, this also adds some uses of isnan() to various places rather than questionable tests for x != x and
x == x to check for NaNs.
+review OPReview
-Fixed casing for PIOS_BL_HELPER_FLASH_ERASE_BOOTLOADER
-fixed wrong condition in f1 bl_helper
-other cosmetic changes and use of stdbool in f1 pios_bl_helper
-remove now unused macros
+review OPReview-456
