HID driver was incorrectly giving back the HID interface
descriptor when asked for the HID descriptor. This should
let OP boards interact better with generic HID layer drivers
and also gives us nicer output in lsusb once the HID descriptor
is read.
for sensing and then load different config for CC and CC3D. Updated the
bootloader as well. Also changed the PIOS_USB_CheckAvailability function to
only return the sense signal and not the transfer_possible flag as this is not
set in time for the bootloader on CC3D for some reason.
The exti layer now allows drivers to register interrupt callbacks
during board initialization. All details of the driver using a
particular EXTI pin have been removed from the EXTI layer so it
can now be used on any board without board-specific modification.
This includes some nice refinements provided by Mike Smith during
initial review. His original commits have been squashed into this
one.
The main purpose of this new COM implementation is that it is
much simpler, and requires less code space. This takes a bit
of the pressure off of the CC bootloader which was right at
the limit of available code space in the bootloader partition.
This is not intended to ever be used by the application.
This driver also formalizes the assumptions in the bootloader's
usage of the COM layer. All messages are assumed to arrive
in atomic chunks from the HID layer.
These files do not contain content from the ID in the header.
This name seems to have been cut/pasted all over throughout
the openpilot source tree and should be removed from any files
that should not rightfully be attributed to this person.
The PIOS_COM_ReceiveBufferUsed() function call is no longer
necessary since the same semantics can be achieved using calls
to PIOS_COM_ReceiveBuffer().
Summary of changes:
* USB CDC and HID drivers are completely split apart.
* This will allow different max buffer sizes for HID and CDC.
* USB descriptors have been overhauled:
* Proper structs/macros/enums declared for USB (see pios_usb_defs.h)
* Two common descriptor definitions. One for HID+CDC another for HID only.
See pios_usb_desc_{hid_cdc,hid_only}.c for details.
* Long standing bugs in OP USB descriptors became much more obvious with the
new struct definitions.
* Board specific USB initialization is now in pios_usb_board_data.h in each build target.
* Definition of USB descriptors is now entirely indpendent of STM32 libs.
Glue into STM32 libs is provided by pios_usbhook.c.
* Removed a lot of stale/irrelevant USB #defines throughout the tree.
* Improved naming consistency throughout USB code:
* PIOS_USB_HID_* now refers to the HID endpoint code.
* PIOS_USB_CDC_* now refers to the CDC endpoint code.
* PIOS_USB_* now refers to the low-level USB code.
* PIOS_USB_BOARD_* now refers to board-specific USB data
* PIOS_USBHOOK_* is glue between PIOS and STM32 USB libs.
* struct usb_* and enum usb_* and USB_* and HID_* are all types from the USB spec.
* Shrunk the buffer size on the CDC call mgmt endpoint to save some RAM.
* Made a few more USB related variables static to save some RAM.
Reduced scope of many variables since they were being
exposed unnecessarily.
Renamed pios_usb_hid_prop code to pios_usbhook to reflect
the fact that it implements all of the callout functions
that are hooked into the stm32 usb library.
No code changes, just file, variable and define names are changed.
First, it better describes the serial protocol used by DSMx satellite
receivers. Second, many people using Spektrum radio, assume Spektrum
protocol. This is the attempt to address those inaccuracies.
- both CC serial ports are now disabled by default (no telemetry);
- serial ports now have DSM2, DSMX (10bit) and DSMX (11bit) options;
- ReceiverGroups now have DSM (MainPort) and DSM (FlexiPort) options.
For DSM2 protocol there is an explicit resolution bit in the stream, so
the DSM2 should be selected. For DSMX there is no such bit, and user
should choose the resolution from the list configuring the spektrum port.
ReceiverGroups have single DSM option which is handled by the same driver.
Downside: this implementation saves received frame first, unrolls by the
end of frame. This should be ok, but may be improved by unrolling channels
on the fly in the rx callback.
Another minor difference is that a ChannelGroup is now bound to port:
DSM (MainPort) or DSM (FlexiPort). This was considered as acceptable
solution in order to not have 6 DSM options for each ChannelGroup and
even more in case of new DSM protocol variations.
Known problem: it is not possible to choose same protocols like
DSM2/DSM2 for two ports. It can be enabled by adding an exception to
common rule, though.
The DSMX throttle channel misbehavior (zero value) is not treated
specially yet. It should trigger the failsafe being out of bounds.
More info and data dumps are required to handle this properly.
In the previous version the decoder could in rare cases get synced from
the middle of data stream in case of data byte equal to the S.Bus start
of frame (SOF) byte (wrong data will be rejected but it was not perfect).
Now it waits for the real start of frame and then checks the SOF byte.
- does not glitch when used in 2-frame mode (DM9, 9503, etc)
- does NOT provides yet DSMX stream decoding - do NOT merge
- uses a bit more time in the interrupt, but frees 16 bytes of RAM.
This is done to help decoding the weird DSMX stream which does not
contain explicit resolution/frame/lost frames info and needs special
processing (to be done yet).
them symbolic constants.
- A timeout is 0
- A missing driver is 65534
- An invalid channel is 65535
ManualControl: Make it deal with the values explicitly. A timed out value
should not be treated like a minimum duration signal. Instead it does not
updated the scaled value but marks the data window as invalid to trigger the
failsafe.
PWM and PPM can now coexist in the same load and be
selected at boot time via the hwsettings UAVObject.
This is basically a complete restructuring of the
way the drivers interact with the TIM peripheral in
the STM32.
As a side effect, the PWM and PPM drivers are now
ready to support multiple instances of each.
This also provides the first step toward being able
to reassign some of the PWM input pins to be servo
output pins. Still more work required, but this is
a good start.
transfers from IRQ. Also catch the double 0x70084 event which was locking up
the FSM with -Os enabled. I did this in a cheating way (filtering the event
based on state) but it's the cleanest I can see. Hopefully a DMA version of
I2C will fix this.
needed by users because if too much changes I change the FS magic and trigger a
wipe.
Possibly the erase should require a particular "magic" object id value to
execute? This would make it harder to do manually through UAVOs though.
This allows the GCS to emulate a receiver device via the
telemetry link.
Select "GCS" as your input type in the manualcontrol config
screen and calibrate it as normal.
Note: The expected values for the channels are in microseconds
just like a PWM or PPM input device. The channel values
are validated against minimum/maximum pulse lengths just
like normal receivers.
The small bootloaders (CC and PipX) are out of flash space
so their stopwatch implementation has been swapped out for
one based on the DELAY clock that takes about 500 bytes less
of code space.
Identical functionality is preserved.
This allows the spektrum and sbus receiver drivers to bind
directly to the usart layer using a properly exported API
rather than overriding the interrupt handler.
Bytes are now pushed directly from the usart layer into the
com layer without any buffering. The com layer performs all
of the buffering.
A further benefit from this approach is that we can put all
blocking/non-blocking behaviour into the COM layer and not
in the underlying drivers.
Misc related changes:
- Remove obsolete .handler field from irq configs
- Adapt all users of PIOS_COM_* functions to new API
- Fixup callers of PIOS_USB_HID_Init()
Update to use 32-bit microsecond values.
Remove PIOS_DELAY_DiffuS per consensus (caller can do it easily themselves).
Update the core delay logic per Stac's suggestion to a version that is
resistant to various overflows.
Each channel was previously tracking a separate driver.
Now, channels are grouped within a channel group to save
RAM used for tracking and to better reflect how channels
are actually mapped.
Also reduce heap has it does not fit in SRAM anymore (not with current compiler).
(that's ok since if there is more space available, it will be reclaimed).
Merge branch 'master' into OP-423_Mathieu_Change_Init_To_Reduce_Memory_Footprint
Conflicts:
flight/CopterControl/System/inc/pios_config.h
flight/Modules/ManualControl/manualcontrol.c
This is a port of a work-in-progress by Sambas onto
the new driver infrastructure needed for boot-time
configuration.
PPM and PWM still don't coexist in a build but this
is closer.
This should mark an end to the compile-time selection of HW
configurations.
Minor changes in board initialization for all platforms:
- Most config structs are marked static to prevent badly written
drivers from directly referring to config data.
- Adapt to changes in .irq fields in config data.
- Adapt to changes in USART IRQ handling.
Major changes in board initialization for CC:
- Use HwSettings UAVObj to decide which drivers to attach to
the "main" port and the flexi port, and select the appropriate
device configuration data.
- HwSettings allows choosing between Disabled, Telemetry, SBUS,
Spektrum,GPS, and I2C for each of the two ports.
- Use ManualControlSettings.InputMode to init/configure the
appropriate receiver module, and register its available rx channels
with the PIOS_RCVR layer. Can choose between PWM, Spektrum and PPM
at board init time. PPM driver is broken, and SBUS will work once
it is added to this UAVObj as an option.
- CC build now includes code for SBUS, Spektrum and PWM receivers in
every firmware image.
PIOS_USART driver:
- Now handles its own low-level IRQs internally
- If NULL upper-level IRQ handler is bound in at board init time
then rx/tx is satisfied by internal PIOS_USART buffered IO routines
which are (typically) attached to the COM layer.
- If an alternate upper-level IRQ handler is bound in at board init
then that handler is called and expected to clear down the USART
IRQ sources. This is used by Spektrum and SBUS drivers.
PIOS_SBUS and PIOS_SPEKTRUM drivers:
- Improved data/API hiding
- No longer assume they know where their config data is stored which
allows for boot-time alternate configurations for the driver.
- Now registers an upper-level IRQ handlerwith the USART layer to
decouple the driver from which USART it is actually attached to.
This separates the RTC device and interrupt handling
from the devices that rely on the tick notifications.
Drivers can now register tick notification functions
that will be called on each RTC tick event.
All receivers now fall under the same driver API provided
by pios_rcvr.c.
This is part of a larger sequence of commits that will
switch the receiver selection over to boot time dynamic
configuration via UAVObjects.