Summary of changes:
* USB CDC and HID drivers are completely split apart.
* This will allow different max buffer sizes for HID and CDC.
* USB descriptors have been overhauled:
* Proper structs/macros/enums declared for USB (see pios_usb_defs.h)
* Two common descriptor definitions. One for HID+CDC another for HID only.
See pios_usb_desc_{hid_cdc,hid_only}.c for details.
* Long standing bugs in OP USB descriptors became much more obvious with the
new struct definitions.
* Board specific USB initialization is now in pios_usb_board_data.h in each build target.
* Definition of USB descriptors is now entirely indpendent of STM32 libs.
Glue into STM32 libs is provided by pios_usbhook.c.
* Removed a lot of stale/irrelevant USB #defines throughout the tree.
* Improved naming consistency throughout USB code:
* PIOS_USB_HID_* now refers to the HID endpoint code.
* PIOS_USB_CDC_* now refers to the CDC endpoint code.
* PIOS_USB_* now refers to the low-level USB code.
* PIOS_USB_BOARD_* now refers to board-specific USB data
* PIOS_USBHOOK_* is glue between PIOS and STM32 USB libs.
* struct usb_* and enum usb_* and USB_* and HID_* are all types from the USB spec.
* Shrunk the buffer size on the CDC call mgmt endpoint to save some RAM.
* Made a few more USB related variables static to save some RAM.
No code changes, just file, variable and define names are changed.
First, it better describes the serial protocol used by DSMx satellite
receivers. Second, many people using Spektrum radio, assume Spektrum
protocol. This is the attempt to address those inaccuracies.
PWM and PPM can now coexist in the same load and be
selected at boot time via the hwsettings UAVObject.
This is basically a complete restructuring of the
way the drivers interact with the TIM peripheral in
the STM32.
As a side effect, the PWM and PPM drivers are now
ready to support multiple instances of each.
This also provides the first step toward being able
to reassign some of the PWM input pins to be servo
output pins. Still more work required, but this is
a good start.
Also reduce heap has it does not fit in SRAM anymore (not with current compiler).
(that's ok since if there is more space available, it will be reclaimed).
Merge branch 'master' into OP-423_Mathieu_Change_Init_To_Reduce_Memory_Footprint
Conflicts:
flight/CopterControl/System/inc/pios_config.h
flight/Modules/ManualControl/manualcontrol.c
This should mark an end to the compile-time selection of HW
configurations.
Minor changes in board initialization for all platforms:
- Most config structs are marked static to prevent badly written
drivers from directly referring to config data.
- Adapt to changes in .irq fields in config data.
- Adapt to changes in USART IRQ handling.
Major changes in board initialization for CC:
- Use HwSettings UAVObj to decide which drivers to attach to
the "main" port and the flexi port, and select the appropriate
device configuration data.
- HwSettings allows choosing between Disabled, Telemetry, SBUS,
Spektrum,GPS, and I2C for each of the two ports.
- Use ManualControlSettings.InputMode to init/configure the
appropriate receiver module, and register its available rx channels
with the PIOS_RCVR layer. Can choose between PWM, Spektrum and PPM
at board init time. PPM driver is broken, and SBUS will work once
it is added to this UAVObj as an option.
- CC build now includes code for SBUS, Spektrum and PWM receivers in
every firmware image.
PIOS_USART driver:
- Now handles its own low-level IRQs internally
- If NULL upper-level IRQ handler is bound in at board init time
then rx/tx is satisfied by internal PIOS_USART buffered IO routines
which are (typically) attached to the COM layer.
- If an alternate upper-level IRQ handler is bound in at board init
then that handler is called and expected to clear down the USART
IRQ sources. This is used by Spektrum and SBUS drivers.
PIOS_SBUS and PIOS_SPEKTRUM drivers:
- Improved data/API hiding
- No longer assume they know where their config data is stored which
allows for boot-time alternate configurations for the driver.
- Now registers an upper-level IRQ handlerwith the USART layer to
decouple the driver from which USART it is actually attached to.
All receivers now fall under the same driver API provided
by pios_rcvr.c.
This is part of a larger sequence of commits that will
switch the receiver selection over to boot time dynamic
configuration via UAVObjects.
ActuatorSettings although for PWM aircrafts it should be done exactly as before
Actuator: Store the update times and maximum update time
OP-14 I2C: Start tracking short history of events and states in driver for
logging
OP-237 Flight/Actuator: Support for I2C based ESCs
OP-237 MK_ESC: Send all four motors as one atomic transfer
OP-237 Flight/Actuator: Allow channels to be mapped to MK I2C interface. Currently
mixer channels are either PWM or MK but in the future this will change to
support more than 8 channels.
OP-16 PiOS/I2C: Further work to try and make I2C more stable, mstly special case
handline in IRQ
OP-237 I2C ESC: Support for Astect 4 channel ESCs
OP-237: When the I2C Actuator write update fails track this
OP-237 Actuator Settings: Change the way motor types are selected to keep that
information more appropriately within ActuatorSettings instead of MixerSettings
Also make motors stay at or above neutral when armed and throttle > 0
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2366 ebee16cc-31ac-478f-84a7-5cbb03baadba
tasks directly update a flag for each module (which they register) and when all
flags set clear the watchdog then.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2365 ebee16cc-31ac-478f-84a7-5cbb03baadba
- New Attitude module for AHRS (skeleton)
- New AttitudeSettings UAVobject
- New AttitudeActual UAVobject
- Regenerated UAVobjects
- Added new UAVobjects to OpenPilot and GCS builds
- New PiOS driver for OpenPilot AHRS (stubs only)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@655 ebee16cc-31ac-478f-84a7-5cbb03baadba
