1
0
mirror of https://bitbucket.org/librepilot/librepilot.git synced 2024-12-04 12:24:11 +01:00
Commit Graph

220 Commits

Author SHA1 Message Date
Stacey Sheldon
075eb65603 bootfault: fail initialization if no telemetry link is configured
This detects a locked out state and fails the init.  The new
bootfault detection code will automatically drop to default
hwsettings after 3 consecutive boot failures.  That will put
the board back into an unlocked state where the user can now
enable a telemetry link using the GCS and everything will be
OK.

NOTE: Any configured telemetry link will be considered enough
      to boot up.  If you only configure a serial telemetry
      link but don't know how to hook anything up to it, this
      will not save you.

As the ultimate recovery, you can always load firmware on the
board that wipes the settings entirely and start over.
2011-12-31 13:08:30 -05:00
Stacey Sheldon
e7053c77f0 usb config: remove unused macro for number of endpoints
This is no longer referenced and is confusing.
2011-12-31 13:02:43 -05:00
Stacey Sheldon
f886af186d bootfault: add support for recovery from init failures
After 3 failed warm start attempts, the init sequence
will force the RAM version of the HWSettings object
to its defaults.  This should allow a user to regain
connectivity to a board that is continually faulting
during init.

This is accomplished by:
 - Incrementing a boot counter that is stored in the
   STM32 BKP registers.  These registers survive a
   warm start but are cleared on a cold start (ie. powerup).
 - On multiple failures, force hwsettings to defaults
   and raise the (new) BootFault alarm to prevent arming.
 - Resetting the boot counter whenever the system manages
   to successfully run the System Module task.

NOTE: This does not actually change the hwsettings object in
      flash.  That's up to the user.

This is intended to catch ONLY faults during early initialization.
It should not be used to recover from faults after the application
is up and running.
2011-12-30 23:05:38 -05:00
Stacey Sheldon
1543a6dbd3 hwsettings: allow disabling of USB telemetry entirely
The GCS hwsettings config widget now disallows any
configuration that disables both HID and VCP telemetry
over the USB port.

The firmware will allow it if the UAVObj is set manually.

This allows a mechanism to reduce RAM usage by another
500 more bytes if USB telemetry can be sacrificed in
certain configurations.
2011-12-30 23:05:38 -05:00
Stacey Sheldon
45615b5812 com: reduce buffer sizes on com interfaces on CC
Now that the COM layer fragments to the underlying
buffer sizes, the COM layer buffers can shrink below
single message sizes.
2011-12-30 23:05:38 -05:00
Stacey Sheldon
7c03875013 diag-tasks: make taskinfo diagnostics a separate enable
This allows task stack analysis without turning on all
of the other diagnostics.
2011-12-30 23:05:37 -05:00
Stacey Sheldon
56c4ff8f40 com-bridge: add support for bridging to flexiport 2011-12-30 23:05:37 -05:00
Stacey Sheldon
60969b57d8 usb-hid: split apart hwsettings for HID and VCP ports
This allows the HID and VCP functions to be configured
separately so that additional functions can be more easily
bound to the VCP port.

This change also provides a safety net that forces either
the HID or VCP to be configured for USB Telemetry.  This
safety net may vanish in the future once the GCS can check
it.  Disabling USB Telemetry entirely would save more than
400 bytes of RAM.
2011-12-30 23:05:37 -05:00
Stacey Sheldon
5b3227d1ff com: reduce buffer sizes for com layer
This saves a few hundred bytes of RAM in a typical
configuration.
2011-12-30 23:05:36 -05:00
Stacey Sheldon
64f498e48a com-bridge: add usart to usb vcp bridge 2011-12-30 23:05:34 -05:00
Stacey Sheldon
504cf3417f init: collapse usart definitions for generic usage
Telemetry and GPS usarts are generic users of the uart
devices.  This collapses the duplicated usart configuration
structs into a single generic one.
2011-12-30 23:05:34 -05:00
Stacey Sheldon
eebdda6276 usb cdc: make HID/CDC configurable in hwsettings 2011-12-30 23:05:34 -05:00
Stacey Sheldon
e6ead85857 usb cdc: fix device descriptor to work on Mac
Apple is very particular about requiring the bDeviceClass
to be set to 2 (Commmunication Device) even for composite
devices which seems wrong.

Device is enumerated without error on Mac now.  Not sure if it
works though.
2011-12-30 23:05:34 -05:00
Stacey Sheldon
c0259dc616 usb cdc: USB composite device with HID + VCP 2011-12-30 23:05:33 -05:00
Oleg Semyonov
10287e3e29 CC: rename ReceiverPort PPM+Servo (Servo) options to PPM+Outputs (Outputs) 2011-12-11 22:52:51 +02:00
Oleg Semyonov
1f60f80053 Bring back the ERASE_FLASH option support for SettingsEraseFirmware 2011-11-26 22:57:33 +02:00
Corvus Corax
aa69027cb2 Merge branch 'next' into CC_GPS 2011-11-11 11:44:11 +01:00
Corvus Corax
e03e3c2ed8 removed "special code" to start optional modules 2011-11-11 11:22:54 +01:00
Oleg Semyonov
f5e82b8242 spektrum: rename Spektrum to DSM (DSM2/DSMJ/DSMX used by Spektrum and JR radios)
No code changes, just file, variable and define names are changed.

First, it better describes the serial protocol used by DSMx satellite
receivers. Second, many people using Spektrum radio, assume Spektrum
protocol. This is the attempt to address those inaccuracies.
2011-11-04 21:40:34 +02:00
Oleg Semyonov
481bff2578 spektrum: code style fixes accoring to OPReview-122 2011-11-01 18:48:07 +02:00
Oleg Semyonov
0116e6a007 spektrum: rework DSM2/DSMJ/DSMX driver for explicit DSMX resolution support
- both CC serial ports are now disabled by default (no telemetry);
- serial ports now have DSM2, DSMX (10bit) and DSMX (11bit) options;
- ReceiverGroups now have DSM (MainPort) and DSM (FlexiPort) options.

For DSM2 protocol there is an explicit resolution bit in the stream, so
the DSM2 should be selected. For DSMX there is no such bit, and user
should choose the resolution from the list configuring the spektrum port.
ReceiverGroups have single DSM option which is handled by the same driver.

Downside: this implementation saves received frame first, unrolls by the
end of frame. This should be ok, but may be improved by unrolling channels
on the fly in the rx callback.

Another minor difference is that a ChannelGroup is now bound to port:
DSM (MainPort) or DSM (FlexiPort). This was considered as acceptable
solution in order to not have 6 DSM options for each ChannelGroup and
even more in case of new DSM protocol variations.

Known problem: it is not possible to choose same protocols like
DSM2/DSM2 for two ports. It can be enabled by adding an exception to
common rule, though.

The DSMX throttle channel misbehavior (zero value) is not treated
specially yet. It should trigger the failsafe being out of bounds.
More info and data dumps are required to handle this properly.
2011-10-30 19:29:03 +02:00
Oleg Semyonov
a19bbba858 Merge branch 'next' into os/alternative_spektrum_driver 2011-10-25 11:55:05 +03:00
James Cotton
27bf2b383e Merge remote-tracking branch 'origin/james/remap_outputs' into next 2011-10-23 18:35:25 -05:00
Oleg Semyonov
4ed23dd891 Output Remapping: renamed PPM_SERVO option to PPM+Servo 2011-10-24 00:34:01 +03:00
James Cotton
24d6ae731b Output Remapping: Added option to just use servo outputs on input lines but not
PPM.  This saves resources.  Good suggestion Os.  In this configuration we
could allow 12 channels of output but for now I'll leave it capped at 10 to
lessen resources on the mixer table.

With spektrum and camera stab enabled there was
1632 bytes heap remaining
180 bytes irq stack remaining
2011-10-23 15:21:40 -05:00
Oleg Semyonov
58d0812309 sbus: better frame syncronization, some cosmetic changes
In the previous version the decoder could in rare cases get synced from
the middle of data stream in case of data byte equal to the S.Bus start
of frame (SOF) byte (wrong data will be rejected but it was not perfect).
Now it waits for the real start of frame and then checks the SOF byte.
2011-10-22 00:44:09 +03:00
Oleg Semyonov
62bca651d5 spektrum: alternative DSMx (DSM2/DSMJ/DSMX) driver
- does not glitch when used in 2-frame mode (DM9, 9503, etc)
- does NOT provides yet DSMX stream decoding - do NOT merge
- uses a bit more time in the interrupt, but frees 16 bytes of RAM.
  This is done to help decoding the weird DSMX stream which does not
  contain explicit resolution/frame/lost frames info and needs special
  processing (to be done yet).
2011-10-21 23:35:17 +03:00
James Cotton
e0cc289de0 Remapping inputs to outputs: Drop S2 so there are ten outputs
Output 7 = S3 input
Output 8 = S4 input
Output 9 = S5 input
Output 10 = S6 input

Also fix bug that prevented them outputting signal
2011-10-20 06:28:07 -05:00
James Cotton
ce7f424131 CC: When receiver port is set to PPM_SERVO use the spare pins as outputs 2011-10-15 16:59:42 -05:00
James Cotton
19c9528d80 CopterControl: Create structures to supply more output channels 2011-10-15 16:59:42 -05:00
Oleg Semyonov
469feecb13 pios: remove some unused #defines 2011-09-28 23:40:12 +03:00
Oleg Semyonov
ed8cf89888 Initcall: fix compilation errors for firmware which does not use Initcalls 2011-09-28 22:57:18 +03:00
Oleg Semyonov
53c098dd08 Merge branch 'next' into os/GPS-on-CopterControl_next_v2
Conflicts:
	flight/OpenPilot/System/pios_board.c
	flight/OpenPilot/UAVObjects.inc
	shared/uavobjectdefinition/hwsettings.xml
2011-09-28 22:02:02 +03:00
James Cotton
6457276438 Merge branch 'input_configuration' into next 2011-09-11 18:52:35 -05:00
Oleg Semyonov
7b3056d10f Input Configuration: fix S.Bus receiver in multi-receiver code 2011-09-12 02:06:48 +03:00
James Cotton
01cd2ded57 Mainboard config: The rcvr port is used for PPM/PWM/Spektrum so make these one
setting that is mutually exclusive.
2011-09-10 14:20:51 -05:00
James Cotton
eb191d869a Mainboard: Get spektrum working again. 2011-09-10 14:19:54 -05:00
Stacey Sheldon
2f86e4dd4f Make PWM/PPM and Servo drivers play nicely together
PWM and PPM can now coexist in the same load and be
selected at boot time via the hwsettings UAVObject.

This is basically a complete restructuring of the
way the drivers interact with the TIM peripheral in
the STM32.

As a side effect, the PWM and PPM drivers are now
ready to support multiple instances of each.

This also provides the first step toward being able
to reassign some of the PWM input pins to be servo
output pins.  Still more work required, but this is
a good start.
2011-08-27 21:39:56 -04:00
James Cotton
c5746335c6 Initialize GCSReceiver object if it is being used 2011-08-27 15:57:09 -05:00
James Cotton
dc340596f5 Merge branch 'next' into GCS_ChangesToUI-RuntimeCFG
Conflicts:
	flight/CopterControl/Makefile
	flight/OpenPilot/System/pios_board.c
	flight/OpenPilot/UAVObjects.inc
	flight/PiOS/STM32F10x/pios_spektrum.c
	ground/openpilotgcs/src/plugins/config/config.pro
	ground/openpilotgcs/src/plugins/config/configgadget.qrc
	ground/openpilotgcs/src/plugins/uavobjects/uavobjects.pro
	shared/uavobjectdefinition/hwsettings.xml
2011-08-27 15:26:05 -05:00
James Cotton
274333a9bf Merge branch 'next' into stac/use-malloc-failed-hook 2011-08-27 00:12:45 -05:00
Corvus Corax
8173c7b7c6 Refactor GPS_PURISTIC into GPS_MINIMAL 2011-08-25 15:44:49 +02:00
Corvus Corax
c63a10d05e CopterControl: Fix GPS buffer sizes 2011-08-25 15:37:38 +02:00
Corvus Corax
4bd72923e5 Merge branch 'CorvusCorax_unidirectional-GPS-com' into CC_GPS
Conflicts:
	flight/Modules/GPS/GPS.c
	flight/Modules/GPS/GTOP_BIN.c
	flight/Modules/GPS/NMEA.c
	shared/uavobjectdefinition/hwsettings.xml
2011-08-25 15:33:23 +02:00
James Cotton
5f7a9b513a Merge branch 'sambas/dsmx_stuff' of ssh://git.openpilot.org/OpenPilot into next
Conflicts:
	shared/uavobjectdefinition/hwsettings.xml
2011-08-24 11:37:30 -05:00
Stacey Sheldon
edc0caf521 heap: set memory critical alarm on malloc failures
Activate the FreeRTOS malloc failed hook and use it
to set the memory critical alarm.
2011-08-21 23:14:32 -04:00
Corvus Corax
53d0732fc6 Enable GPS module as "optional module" in CooterControl 2011-08-20 01:25:49 +02:00
Corvus Corax
dfd301571a HWSettings: Allow late Initialization and Start of Modules as defined in Makefile(available modules) and UAVObject(actually started modules) 2011-08-20 01:24:06 +02:00
James Cotton
86b652bbab Merge branch 'next' into camera_stabilization 2011-08-14 18:07:57 -05:00
zedamota
e736b17cc4 Merge remote-tracking branch 'remotes/origin/next' into GCS_ChangesToUI-RuntimeCFG
Conflicts:
	ground/openpilotgcs/src/plugins/config/config_cc_hw_widget.cpp
	ground/openpilotgcs/src/plugins/config/configgadgetwidget.h
	ground/openpilotgcs/src/plugins/config/configstabilizationwidget.cpp
2011-08-14 15:48:16 +01:00
James Cotton
f766ba47aa Increase the size of the eventdispatcher task and lower the maximum queue size. 2011-08-13 19:21:58 -05:00
sambas
1e67b5e3b5 DSMx_binder, hw setting 0 disabled, 1-10 bind pulses. Manual disable after successful bind. Only for flexiport. 2011-08-06 22:16:47 +03:00
James Cotton
a592e7d398 ManualControlSettings must be also initialized in pios_board.c 2011-08-04 07:47:50 -05:00
Stacey Sheldon
06cdeb7b61 rcvr: support multiple simultaneous receivers
Now also supports multiple instances of the Spektrum driver.
These are configured as Spektrum1 and Spektrum2.
2011-08-02 01:22:04 -04:00
Stacey Sheldon
829b8b83f6 rcvr: Add GCS receiver driver for rcvr via telemetry
This allows the GCS to emulate a receiver device via the
telemetry link.

Select "GCS" as your input type in the manualcontrol config
screen and calibrate it as normal.

Note: The expected values for the channels are in microseconds
      just like a PWM or PPM input device.  The channel values
      are validated against minimum/maximum pulse lengths just
      like normal receivers.
2011-08-02 01:22:04 -04:00
James Cotton
035b4103c4 Need to initialize the HwSettings before using them. 2011-07-31 09:42:15 +09:00
James Cotton
3df730c64f Merge branch 'stac/refactor-usart-com' into camera_stabilization 2011-07-30 13:38:43 +09:00
James Cotton
387a22398e Make it possible to optionally enable the CameraStab module 2011-07-30 12:08:47 +09:00
Stacey Sheldon
8c0b60099f rcvr: don't init spektrum and sbus rcvrs twice 2011-07-29 22:59:50 -04:00
James Cotton
ae67c51632 Register some missing objects with their modules 2011-07-30 11:28:21 +09:00
James Cotton
2e5a36a4db Merge branch 'stac/refactor-usart-com' into camera_stabilization 2011-07-30 10:55:16 +09:00
James Cotton
b2d2114ede Disable auto registration of all objects. Later the uavobj_init linker scripts
should be deleted to not carry around old code.
2011-07-30 10:24:46 +09:00
James Cotton
23e9b56839 Dos2unix flight/CopterControl/System/coptercontrol.c 2011-07-30 10:06:35 +09:00
James Cotton
96c2d24253 Merge branch 'next' into camera_stabilization
Conflicts:
	flight/CopterControl/Makefile
	flight/CopterControl/System/coptercontrol.c
	flight/Modules/Actuator/actuator.c
	flight/Modules/GPS/GPS.c
	flight/Modules/ManualControl/manualcontrol.c
	flight/Modules/Stabilization/stabilization.c
	flight/Modules/System/systemmod.c
	shared/uavobjectdefinition/manualcontrolsettings.xml
	shared/uavobjectdefinition/stabilizationdesired.xml
2011-07-30 10:06:10 +09:00
Stacey Sheldon
c2fb0d8b43 com: allow run-time allocation of buffers 2011-07-29 15:33:14 -04:00
Stacey Sheldon
5f8760a55c com: Move buffering out of USART/HID layer and into COM layer
This allows the spektrum and sbus receiver drivers to bind
directly to the usart layer using a properly exported API
rather than overriding the interrupt handler.

Bytes are now pushed directly from the usart layer into the
com layer without any buffering.  The com layer performs all
of the buffering.

A further benefit from this approach is that we can put all
blocking/non-blocking behaviour into the COM layer and not
in the underlying drivers.

Misc related changes:
 - Remove obsolete .handler field from irq configs
 - Adapt all users of PIOS_COM_* functions to new API
 - Fixup callers of PIOS_USB_HID_Init()
2011-07-27 19:45:38 -04:00
Stacey Sheldon
8dbace5ee2 Merge branch 'rcvr_mem_reduction'
Conflicts:
	flight/PiOS/STM32F10x/link_STM32103CB_CC_Rev1_sections.ld
2011-07-17 17:14:40 -04:00
James Cotton
d41260d54c Make the stabilization settings query correctly now by increasing the TX buffer
on the CC side to 256 bytes instead of 128 to support large objects (max object
size is 256 bytes)
2011-07-15 10:40:21 -05:00
Stacey Sheldon
6580462916 rcvr: specify drivers for groups of channels
Each channel was previously tracking a separate driver.
Now, channels are grouped within a channel group to save
RAM used for tracking and to better reflect how channels
are actually mapped.
2011-07-14 23:22:42 -04:00
sambas
18a5465246 Bugfix: CC flexiport spektrum config
Working spektrum bind routine, depending your TX try BIND_PULSES 3,5,7,9 (5 works with DX7)
Boot process takes too long on MB so bind command misses the window (20-140ms).
2011-07-14 14:43:26 +03:00
James Cotton
2fe7ee40b1 Merge branch 'OP-423_Mathieu_Change_Init_To_Reduce_Memory_Footprint' 2011-07-12 12:44:59 -05:00
James Cotton
15a2b85729 For OpenPilot use the minimal stack size (512 words) for eventdispatcher as
this is necessary for object saving.  Creating a new define to override this
for CopterControl down to 96.
2011-07-12 12:34:40 -05:00
Mathieu Rondonneau
d38f6167e3 OP-423:
Also reduce heap has it does not fit in SRAM anymore (not with current compiler).
(that's ok since if there is more space available, it will be reclaimed).

Merge branch 'master' into OP-423_Mathieu_Change_Init_To_Reduce_Memory_Footprint

Conflicts:
	flight/CopterControl/System/inc/pios_config.h
	flight/Modules/ManualControl/manualcontrol.c
2011-07-08 06:29:34 -07:00
Stacey Sheldon
b86ef4de82 bootcfg: fix incorrect bounds checking on rcvr registration
This was preventing any receivers from registering their
channels.
2011-07-07 23:59:12 -04:00
Stacey Sheldon
1f004ee896 ppm: port PPM driver onto new CC driver layers
This is a port of a work-in-progress by Sambas onto
the new driver infrastructure needed for boot-time
configuration.

PPM and PWM still don't coexist in a build but this
is closer.
2011-07-07 22:27:57 -04:00
Stacey Sheldon
226f095a2e bootcfg: remove baudrate #defines for USARTs
The initial baud rates of each interface are now forced in the
board init code.

Any modules using USARTs should have fields added to
their settings object to allow the user to change the
baud rate from the default by using the COM layer APIs.

Developers requiring custom baud rates before the settings
objects are in place should locally edit the cfg structs
to specify the desired baud rates.
2011-07-06 23:03:54 -04:00
Stacey Sheldon
a8787ee015 bootcfg: Add support for selecting S.Bus receivers in inputtype 2011-07-06 22:38:23 -04:00
Stacey Sheldon
e82539c654 bootcfg: additional validation during board init 2011-07-06 22:34:59 -04:00
Stacey Sheldon
dbf7574946 bootcfg: use UAVobj to control boot-time HW config
This should mark an end to the compile-time selection of HW
configurations.

Minor changes in board initialization for all platforms:
 - Most config structs are marked static to prevent badly written
   drivers from directly referring to config data.
 - Adapt to changes in .irq fields in config data.
 - Adapt to changes in USART IRQ handling.

Major changes in board initialization for CC:
 - Use HwSettings UAVObj to decide which drivers to attach to
   the "main" port and the flexi port, and select the appropriate
   device configuration data.
 - HwSettings allows choosing between Disabled, Telemetry, SBUS,
   Spektrum,GPS, and I2C for each of the two ports.
 - Use ManualControlSettings.InputMode to init/configure the
   appropriate receiver module, and register its available rx channels
   with the PIOS_RCVR layer.  Can choose between PWM, Spektrum and PPM
   at board init time.  PPM driver is broken, and SBUS will work once
   it is added to this UAVObj as an option.
 - CC build now includes code for SBUS, Spektrum and PWM receivers in
   every firmware image.

PIOS_USART driver:
 - Now handles its own low-level IRQs internally
 - If NULL upper-level IRQ handler is bound in at board init time
   then rx/tx is satisfied by internal PIOS_USART buffered IO routines
   which are (typically) attached to the COM layer.
 - If an alternate upper-level IRQ handler is bound in at board init
   then that handler is called and expected to clear down the USART
   IRQ sources.  This is used by Spektrum and SBUS drivers.

PIOS_SBUS and PIOS_SPEKTRUM drivers:
 - Improved data/API hiding
 - No longer assume they know where their config data is stored which
   allows for boot-time alternate configurations for the driver.
 - Now registers an upper-level IRQ handlerwith the USART layer to
   decouple the driver from which USART it is actually attached to.
2011-07-05 22:03:25 -04:00
Stacey Sheldon
6415fc84a5 rtc: allow registration of callbacks on RTC tick
This separates the RTC device and interrupt handling
from the devices that rely on the tick notifications.

Drivers can now register tick notification functions
that will be called on each RTC tick event.
2011-07-05 22:03:25 -04:00
Stacey Sheldon
740b5f1584 rcvr: convert PWM, PPM, SBUS and Spektrum to use PIOS_RCVR
All receivers now fall under the same driver API provided
by pios_rcvr.c.

This is part of a larger sequence of commits that will
switch the receiver selection over to boot time dynamic
configuration via UAVObjects.
2011-07-05 22:03:25 -04:00
Stacey Sheldon
0c4facac46 heap: reduce stack size on IDLE and Event tasks
The FreeRTOS IDLE task was using 512 bytes of stack.
The UAVObject Event task was also using 512 bytes of stack.

Both have been reduced, recovering 400+ bytes of heap.
2011-07-05 20:13:00 -04:00
Mathieu Rondonneau
b3740ec025 OP-423: Clean startup and add weak function call for stack swap. 2011-07-03 12:43:38 -07:00
Corvus Corax
fc62f6e522 Module initialisation rework ported to PiOS.posix 2011-06-26 00:25:06 +02:00
Mathieu Rondonneau
6683ce8570 OP-423: Make it more obvious that MODULE_TASKCREATE_ALL and MODULE_INITIALIZE_ALL are macro (for now):
- remove the ;
  - also encapsulate the macro by {} in his own scope.
2011-06-25 11:40:01 -07:00
Mathieu Rondonneau
dcd2774103 OP-423 Fix some comment from code review:
- update example module
- use module init macro for POSIX and WIN to make code cleaner.
2011-06-24 06:59:51 -07:00
Mathieu Rondonneau
703919daf4 OP-423 Reduce IRQ stack limits (CC onlyt) 2011-06-22 06:32:27 -07:00
Mathieu Rondonneau
0ff5e9a46f Merge branch 'master' into OP-423_Mathieu_Change_Init_To_Reduce_Memory_Footprint 2011-06-21 22:02:13 -07:00
James Cotton
8976d22fad Merge remote-tracking branch 'origin/OP-159_os_sbus' 2011-06-21 17:51:22 -05:00
Oleg Semyonov
fba201c8b3 usart: move default port numbers from pios_config.h to pios_board.c 2011-06-22 01:32:18 +03:00
Mathieu Rondonneau
fc1e3f574c OP-423: Split task create and module init in order to postpone task creation once the full heap is available.
Also implement some ordering (quite ugly still) in the module init and task creation order so we can decide which module to start/init first
and which module to start/init last.
This will be replaced/adapter with the uavobject list later (once it's implemented).
reserving some space for module init and task create parameters to customize module/task creation (this will be usefull once we get the list and customization from customer).

Changes have been made for OP and CC. Tested comped with CC,OP, sim_posix.
Only ran on bench with CC for couple of minutes (code increase expected but no dropping of stack which is good).

This gives task creation at the time wherethe all heap is available.
2011-06-19 22:35:40 -07:00
Oleg Semyonov
6272210df7 sbus: some code cleanup (no functional changes) 2011-06-19 14:30:13 +03:00
Mathieu Rondonneau
2b11395a67 OP-423 just move stack from systemmod back to heap (200 bytes) that are not needed anymore. 2011-06-18 17:31:29 -07:00
Mathieu Rondonneau
5e3e7cc4e3 OP-423 Fix issue with init not properly started in the right order endup up object thinking other where not init. 2011-06-18 17:28:37 -07:00
Oleg Semyonov
311902f1f2 sbus: implemented S.Bus stream decoding 2011-06-18 23:19:57 +03:00
James Cotton
724016ffb0 When erasing flash at the end start flashing LED to indicate it is done 2011-06-18 14:32:09 -05:00
James Cotton
5044ea36de Start initializing objects in the modules that consume them. Shouldn't affect
OP yet but not tested.
2011-06-18 14:20:51 -05:00
Mathieu Rondonneau
b67a38661e OP-423: merge master into that branch, resolve conflicts and test with CC and bl_CC
heap reamining is low (about 500) but stacks can be ajusted (specially the 200 bytes from system) to give the level close to 1Ko if needed.

Merge branch 'master' into OP-423_Mathieu_Change_Init_To_Reduce_Memory_Footprint

Conflicts:
	flight/CopterControl/System/inc/FreeRTOSConfig.h
	flight/CopterControl/System/inc/pios_config.h
2011-06-17 19:04:09 -07:00
James Cotton
9720a8444f Make a few things optional if they are mostly for diagnostics to keep memory
down
2011-06-17 21:00:21 -05:00
Mathieu Rondonneau
65cf467ca4 OP-423: move the module initialize funtion into a specific section for OP and CC.
- create linker section for those <module>Initialize()
- later this list will incorporate parameters as well. (this probably will be more a OP feature to swap/remove/delete module on the fly.
- this is not done at compile time anymore by Makefile.
- this will allow us to have control on the module start at run-time (not implemented but build the ground for it).
- this simplify the startup (Part of code re-org).
- this change does not affect sim_posix and win32 (since they don't need that)
- ensure it's compiling for PiOS.posix
- port to PiOS.win32 but not tested (not compiled)
- tested on CC
- compile on OP.
- this free ~200 bytes.
- current avalable bytes (is we keep the same remaining bytes on the stack than before) is easily passed the 1.2Ko mark on CC with new gcc (4.5.2)
- this does not include init-reorg for each module (I still think more can be freed)
2011-06-16 22:13:19 -07:00