priority preempts) and adjusting the priorities around to be more sensible.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2355 ebee16cc-31ac-478f-84a7-5cbb03baadba
but not having telemetry causes a reset. If the buffer got full enough it
would never start to transmit again.
Note: also making Telemetry non-blocking
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2346 ebee16cc-31ac-478f-84a7-5cbb03baadba
(which is good) but that stops the comms polling. This makes it happen
ocassionally but not too much.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2335 ebee16cc-31ac-478f-84a7-5cbb03baadba
range of NaN. This would reflect a race condition probably from the SPI
interaction.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2334 ebee16cc-31ac-478f-84a7-5cbb03baadba
to only transmitting one object per transmission too to keep size down.
Also move to using the driver structure so the paramter is in a clear place.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2333 ebee16cc-31ac-478f-84a7-5cbb03baadba
Battery module for Power Sensor version 2
This is the first checkin of code for the new sensor board.
This has been tested for Voltage calibration bit not Current yet.
This will set and clear system alarms appropriately.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2323 ebee16cc-31ac-478f-84a7-5cbb03baadba
As this changes UAVObjects both flight and GCS software will need to be recompiled to stay in sync.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2303 ebee16cc-31ac-478f-84a7-5cbb03baadba
As this changes UAVObjects both flight and GCS software will need to be recompiled to stay in sync.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2302 ebee16cc-31ac-478f-84a7-5cbb03baadba
This allows the UAVObjectGenerator generated code to set the default values.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2301 ebee16cc-31ac-478f-84a7-5cbb03baadba
Error when GPS disconnected
OK when >=7 satellites and PDOP <3.5
Warning when only 3Dfix
Critical otherwise
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2297 ebee16cc-31ac-478f-84a7-5cbb03baadba
This means that any defined alarms that don't have their flight module compiled in will show uninitialised rather than OK
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2295 ebee16cc-31ac-478f-84a7-5cbb03baadba
Added:
Battery
Flight Time
I2C
GPS
Also added new alarm state of "Uninitialised"
no code to set these alarms yet.
As this changes UAVObjects both flight and GCS software will need to be recompiled to stay in sync.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2294 ebee16cc-31ac-478f-84a7-5cbb03baadba
error message for embedded stuff.
Note: this was only tested on PC although I'm fairly confident about it.
Please let me know about any errors.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2285 ebee16cc-31ac-478f-84a7-5cbb03baadba
will run slower but greatly reduce the memory footprint (360 floats less).
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2284 ebee16cc-31ac-478f-84a7-5cbb03baadba
settings but only be used when home location is valid. Also discard any mag
data that is all zeros although we shouldn't see this.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2283 ebee16cc-31ac-478f-84a7-5cbb03baadba
little aggressive. Also increased the drift rate of the gyro bias per Sambas'
testing (thanks) although not to the levels required for flying through 40 deg
C transitions.
Made the dump_ekf function handle both numbers of states
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2282 ebee16cc-31ac-478f-84a7-5cbb03baadba
before because if transmission got NAK then sending would stop. Now the next
time data is added to the buffer a new send will be attempted.
fifoBuf: in clearData just set the read pointer to the write pointer. This is
safer for multiple people accessing it assuming the reader will be clearing it.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2279 ebee16cc-31ac-478f-84a7-5cbb03baadba
what they would be on a real board. Also fixed a typo in stabilization.c which made me lose time when trying to understand the code...
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2260 ebee16cc-31ac-478f-84a7-5cbb03baadba
FirmwareIAP to get me back for breaking Sys_Reset. You got me! :)
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2246 ebee16cc-31ac-478f-84a7-5cbb03baadba
required for longer sequences, Need to deal with when it happens
inappropriately better.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2245 ebee16cc-31ac-478f-84a7-5cbb03baadba
sometimes thrown, and made errors not lock it up by default. It works for me,
but since this has historically been associated with lots of lock ups please
check your systems carefully.
PiOS/I2C: Make the bus by default try to recover from errors instead of locking
up
PiOS/I2C: After a bus error and clocking all previous data create a STOP
condition to make sure bus is released (note, this also requires creating a
START condition first)
PiOS/I2C: If the same event hits the I2C bus twice in a row then disregard
second one, there is no situation where we should get the same event multiple
times that matters and this gets us out really quickly to catch the real
events. I was seeing this with repeated 0x70084 which means byte transmitted.
This is related to STM32 bugs in the IRQ timings I believe.
PiOS/I2C: 1) Mask out some bits we don't care about in the event flags
2) Don't lock up if the give semaphore fails, although why it does is strange
3) Recover from bus failure through the "auto" state path instead of just
coding state
PiOS/I2C: Change the reset bus code to follow
http://www.analog.com/static/imported-files/application_notes/54305147357414AN686_0.pdf
(thanks for the reference Neontangerine). Although this may actually NOT clear
the bus the first time through, subsequent bus errors should eventually clock
it out. The up side is it is less likely to clock a bunch of 1s into an ESC
and make it run up.
PiOS/I2C: Some cleaned up code for getting a snippet of the history when
something strange happens
PiOS/I2C: Export logging information from I2C through a UAV object
PiOS/I2C: Improve the diagnostic information
PiOS/I2C: Need to handle the event 0x30084. This seems to happen between a
byte transmitted and new byte started
PiOS/I2C: Handle the NACK condition by simply going to the stopping state.
PiOS/I2C: Add a new NACK state to handle sending the STOP signal after a NACK
following the STM documentation. Other error conditions still are not dealt
with.
PiOS/I2C: Should handle the NACK condition from all the write cases. Need to
think about read cases
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2239 ebee16cc-31ac-478f-84a7-5cbb03baadba
and starting transmission again. This should address the bootloader locking up
on verify.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2235 ebee16cc-31ac-478f-84a7-5cbb03baadba
BEWARE: I have not flown my quad with this code, so please be careful, test, and report!
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2234 ebee16cc-31ac-478f-84a7-5cbb03baadba
bias as gravity vector facing down (bad for planes) which is diabled by
default.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2232 ebee16cc-31ac-478f-84a7-5cbb03baadba
configuration structures are const which keeps them in flash instead of ram.
However the library needs to declare them const for the compiler to work.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2231 ebee16cc-31ac-478f-84a7-5cbb03baadba
Implements RS232(Telemetry) uploads using Kokomo's protocol.
This is a test version, the code will never timeout and jump to user space code.
If USB is connected on Power Up it will be used, if not RS232 will be used instead.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2211 ebee16cc-31ac-478f-84a7-5cbb03baadba
than the ekf runs and also be more tolerant of timing jitter
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2191 ebee16cc-31ac-478f-84a7-5cbb03baadba
from the AHRS code (which will facilitate code integration with new INS) and
also will help set up a fifo queue for the downsampled data to allow gyro data
output from AHRS faster than EKF output. Also decreased ADC interrupt priority
so the SPI comms don't drop out.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2190 ebee16cc-31ac-478f-84a7-5cbb03baadba
bias correction. This is useful for stabilization to get rid of the gyro bias.
Making it an option is important for calibration.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2189 ebee16cc-31ac-478f-84a7-5cbb03baadba
bounded. Velocity variance still comes from AHRSCalibration.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2186 ebee16cc-31ac-478f-84a7-5cbb03baadba
ManualControlSettings so that planes can disable the timeout
feature for gliding (holding roll on a plane not so good).
Note: This will require you to reconfigure your ManualControlSettings
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2185 ebee16cc-31ac-478f-84a7-5cbb03baadba
Three files added to AHRS which add accelerometer biases (16 states) to the INS/GPS. Added for evaluation (give it a try James).
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2182 ebee16cc-31ac-478f-84a7-5cbb03baadba
will automatically disarm after 30 seconds without motor. This behavior will
need to be parameterized for planes which might idle for a while.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2181 ebee16cc-31ac-478f-84a7-5cbb03baadba
velocity to help stabilize attitude. In principle the mag should be fine but
in practice I need this.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2160 ebee16cc-31ac-478f-84a7-5cbb03baadba
indoor from the name since it's used for both indoor and outdoor mode now.
Increased default value to 0.4 to better reflect the GPS accuracy.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2156 ebee16cc-31ac-478f-84a7-5cbb03baadba
how various sensors are used in the INS update. Also added slow filter to
track offset between GPS and baro in outdoor mode.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2154 ebee16cc-31ac-478f-84a7-5cbb03baadba
Changes in ahrs.c for new initialization and to fix issues with outdoor algorithm. The changes in ahrs.c are pretty messy, but committed mostly to get the code to Peabody for more extensive restructuring of ahrs.c.
git-svn-id: svn://svn.openpilot.org/OpenPilot/trunk@2150 ebee16cc-31ac-478f-84a7-5cbb03baadba
